Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM43601PWPR

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

LM43601PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output Switching output of the regulator, internally connected to both power MOSFETs; connect to power inductor.
2 SW output Switching output of the regulator, internally connected to both power MOSFETs; connect to power inductor.
3 CBOOT power_out Bootstrap capacitor connection for high-side driver; connect a high-quality 470-nF capacitor from CBOOT to SW.
4 VCC power_out Internal bias supply output for bypassing; connect bypass capacitor from this pin to AGND, do not connect external load or short to ground during operation.
5 BIAS input Optional internal LDO supply input; tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V or external 3.3 V/5 V rail, place bypass capacitor 1 to 10 µF to ground, tie to ground when not in use.
6 SYNC input Clock input to synchronize switching action to external clock from 200 kHz to 2.2 MHz with high-speed termination; connect to ground if not used.
7 RT input Connect resistor RT from this pin to AGND to program switching frequency; leave floating for 500 kHz default switching frequency.
8 PGOOD output Open-drain output for power-good flag; use 10 kΩ to 100 kΩ pullup resistor to logic rail no higher than 12 V.
9 FB input Feedback sense input pin connected to midpoint of feedback divider to set VOUT; do not short this pin to ground during operation.
10 AGND power_in Analog ground pin providing ground reference for internal references and logic; connect to system ground.
11 SS/TRK input Soft-start control pin; leave floating for internal soft-start slew rate or connect capacitor to extend soft-start time or external voltage ramp for tracking.
12 EN input Enable input to LM43601 with high = ON and low = OFF; connect to VIN or through resistor divider or external voltage/logic source, do not float.
13 VIN power_in Supply input pin to internal LDO and high-side power FET operating range 3.5 V to 36 V; connect to power supply and bypass capacitors CIN with shortest path.
14 VIN power_in Supply input pin to internal LDO and high-side power FET operating range 3.5 V to 36 V; connect to power supply and bypass capacitors CIN with shortest path.
15 PGND power_in Power ground pin connected internally to low-side power FET; connect to system ground, PAD, AGND, and ground pins of CIN and COUT with shortest path to CIN.
16 PGND power_in Power ground pin connected internally to low-side power FET; connect to system ground, PAD, AGND, and ground pins of CIN and COUT with shortest path to CIN.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN to PGND -0.3 42 V 4
EN to PGND -0.3 V 4
FB, RT, SS/TRK to AGND -0.3 3.6 V 4
PGOOD to AGND -0.3 15 V 4
SYNC to AGND -0.3 5.5 V 4
BIAS to AGND -0.3 30 V 4
AGND to PGND -0.3 0.3 V 4
SW to PGND -0.3 V 4
SW to PGND less than 10-ns transients -3.5 42 V less than 10-ns transients 4
CBOOT to SW -0.3 5.5 V 4
VCC to AGND -0.3 3.6 V 4
Storage temperature Tstg -65 150 °C 4
VIN to PGND 3.5 36 V 4
EN -0.3 V 4
FB -0.3 1.1 V 4
PGOOD -0.3 12 V 4
BIAS input not used -0.3 0.3 V BIAS input not used 4
BIAS input used 3.3 V BIAS input used 4
AGND to PGND -0.1 0.1 V 4
Output voltage VOUT 1 28 V 4
Output current IOUT 0 1 A 4
Operating junction temperature range TJ -40 125 °C 4
Shutdown quiescent current ISHDN 1.1 3.1 µA VEN = 0 V 5
Operating quiescent current (non-switching) from VIN IQ-NONSW 6 11 µA VEN = 3.3 V, VFB = 1.5 V, VBIAS = 3.4 V external 5
Operating quiescent current (non-switching) from external VBIAS IBIAS-NONSW 85 140 µA VEN = 3.3 V, VFB = 1.5 V, VBIAS = 3.4 V external 5
Precision enable level for switching and regulator output VOUT (rising) VEN-VOUT-H 2 2.1 2.42 V VENABLE high level 5
Enable input leakage current ILKG-EN 0.8 1.75 µA VEN = 3.3 V 5
Feedback voltage VFB 1.009 1.016 1.023 V TJ = 25°C 6
Feedback voltage VFB 0.999 1.016 1.031 V TJ = –40°C to 85°C 6
Feedback voltage VFB 0.999 1.016 1.039 V TJ = –40°C to 125°C 6
Input leakage current at FB pin ILKG-FB 0.2 65 nA FB = 1.016 V 6
Peak inductor current limit IHS-LIMIT 2.07 2.45 2.71 A 6
Valley inductor current limit ILS-LIMIT 0.94 1.1 1.25 A 6
Soft-start charge current ISSC 1.17 2.2 2.85 µA 6
Power-good flag overvoltage tripping threshold (% of FB voltage) VPGOOD-HIGH 110 113 % 6
Power-good flag undervoltage tripping threshold (% of FB voltage) VPGOOD-LOW 83 90 % 6
PGOOD pin pulldown resistance when power bad RPGOOD 40 125 Ω VEN = 3.3 V 6
PGOOD pin pulldown resistance when power bad RPGOOD 60 150 Ω VEN = 0 V 6
Internal LDO input change-over threshold to BIAS (VBIAS rising) VBIAS-ON 2.96 3.2 V VBIAS rising threshold 5
Minimum input voltage for startup VIN-MIN-ST 3.8 V 5
Minimum high side MOSFET ON-time tON-MIN 125 165 ns Specified by design 7
Minimum high side MOSFET OFF-time tOFF-MIN 200 250 ns Specified by design 7
Oscillator default frequency FOSC-DEFAULT 445 500 570 kHz RT pin open circuit 7
Minimum adjustable frequency FADJ 200 kHz With 1% resistors at RT pin 7
Maximum adjustable frequency 2200 kHz 7
Sync clock maximum duty cycle DSYNC-MAX 90 % 7
Sync clock minimum duty cycle DSYNC-MIN 10 % 7
Minimum sync clock ON- and OFF-time TSYNC-MIN 80 ns 7
Junction-to-ambient thermal resistance RθJA 39.9 °C/W JESD 51-7, 4-layer board, 1 W power dissipation 5
Junction-to-case (top) thermal resistance RθJC(top) 26.9 °C/W 5
Junction-to-board thermal resistance RθJB 21.7 °C/W 5
Junction-to-top characterization parameter ψJT 0.8 °C/W 5
Junction-to-board characterization parameter ψJB 21.5 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 2.3 °C/W 5

CAD (KiCad official)

  • Symbol: LM43601PWPR
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm43601pwpr-etched.step / lm43601pwpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm43601pwpr.step / lm43601pwpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (56 pp, sha256 84f11e12b19d28c7, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF