Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM43600AQPWPRQ1

Texas Instruments · DC-DC Converters · HTSSOP-16-EP

LM43600AQPWPRQ1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW passive Switching output of the regulator, internally connected to both power MOSFETs; connect to the power inductor.
2 SW passive Switching output of the regulator, internally connected to both power MOSFETs; connect to the power inductor.
3 CBOOT passive Bootstrap capacitor connection for the high-side driver; connect a high-quality 470-nF capacitor from CBOOT to SW.
4 VCC power_in Internal bias supply output for bypassing; connect a bypass capacitor to AGND, do not connect an external load, and never short to ground during operation.
5 BIAS power_in Optional internal LDO supply input; tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V or to an external 3.3 V or 5 V rail, with a 1 to 10 µF bypass capacitor, and tie to ground when not in use (do not float).
6 SYNC input Clock input to synchronize switching to an external clock; connect to ground if not used and do not float.
7 RT passive Connect a resistor RT to AGND to program the switching frequency; leave floating for the 500 kHz default.
8 PGOOD output Open-drain power-good flag output; use a 10-kΩ to 100-kΩ pullup to a logic rail or DC voltage no higher than 12 V.
9 FB input Feedback sense input connected to the midpoint of the feedback divider to set VOUT; do not short to ground during operation.
10 AGND power_in Analog ground, reference for internal references and logic; connect to system ground.
11 SS/TRK input Soft-start control pin; leave floating for internal soft-start, connect a capacitor to extend soft-start time or an external voltage ramp for tracking.
12 EN input Enable input (high = ON, low = OFF); connect to VIN, to VIN through a resistor divider, or to an external voltage or logic source, and do not float.
13 VIN power_in Supply input to the internal LDO and high-side power FET (3.5 V to 36 V recommended); connect to the supply and CIN bypass capacitors with a very short path.
14 VIN power_in Supply input to the internal LDO and high-side power FET (3.5 V to 36 V recommended); connect to the supply and CIN bypass capacitors with a very short path.
15 PGND power_in Power ground connected internally to the low-side power FET; connect to system ground, PAD, AGND, and CIN and COUT grounds.
16 PGND power_in Power ground connected internally to the low-side power FET; connect to system ground, PAD, AGND, and CIN and COUT grounds.
17 PAD passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Shutdown quiescent current ISHDN 1.1 3.1 µA VEN = 0 V 5
Operating quiescent current (non-switching) from VIN IQ-NONSW 6 11 µA VEN = 3.3 V, VFB = 1.5 V, VBIAS = 3.4 V external 5
Operating quiescent current (non-switching) from external VBIAS IBIAS-NONSW 85 140 µA VEN = 3.3 V, VFB = 1.5 V, VBIAS = 3.4 V external 5
Minimum input voltage for start-up VIN-MIN-ST 3.8 V 5
Precision enable level for switching and regulator output VEN-VOUT-H 2 2.1 2.42 V VENABLE high level 5
Enable input leakage current ILKG-EN 0.8 1.75 µA VEN = 3.3 V 5
VBIAS changeover threshold VBIAS-ON 2.96 3.2 V VBIAS rising threshold 5
Feedback voltage VFB 1.009 1.016 1.023 V TJ = 25°C 6
Feedback voltage VFB 0.999 1.016 1.031 V TJ = -40°C to 85°C 6
Feedback voltage VFB 0.999 1.016 1.039 V TJ = -40°C to 125°C 6
FB input leakage current ILKG-FB 0.2 65 nA FB = 1.011 V 6
Peak inductor current limit IHS-LIMIT 1.04 1.33 1.56 A 6
Inductor current valley limit ILS-LIMIT 0.46 0.6 0.75 A 6
Soft-start charge current ISSC 1.17 2.2 2.85 µA 6
Power-good overvoltage tripping threshold VPGOOD-HIGH 110 113 % % of FB voltage 6
Power-good undervoltage tripping threshold VPGOOD-LOW 83 90 % % of FB voltage 6
PGOOD pulldown resistance when power bad RPGOOD 69 150 Ω LM43600A-Q1: VEN = 3.3 V 6
PGOOD pulldown resistance when power bad RPGOOD 150 350 Ω LM43600A-Q1: VEN = 0 V 6
Minimum high side MOSFET ON time tON-MIN 125 165 ns 7
Minimum high side MOSFET OFF time tOFF-MIN 200 250 ns 7
Oscillator default frequency FOSC-DEFAULT 445 500 570 kHz RT pin open circuit 7
Frequency adjust accuracy FADJ 10 % With 1% resistors at RT pin 7
VIN to PGND (abs max) VIN -0.3 42 V 4
EN to PGND (abs max) EN -0.3 V max VIN + 0.3 V 4
FB, RT, SS/TRK to AGND (abs max) -0.3 3.6 V 4
PGOOD to AGND (abs max) -0.3 15 V 4
SYNC to AGND (abs max) -0.3 5.5 V 4
BIAS to AGND (abs max) -0.3 30 V 4
AGND to PGND (abs max) -0.3 0.3 V 4
SW to PGND less than 10-ns transients -3.5 42 V 4
CBOOT to SW (abs max) -0.3 5.5 V 4
VCC to AGND (abs max) -0.3 3.6 V 4
Storage temperature Tstg -65 150 °C 4
ESD HBM V(ESD) -2000 2000 V HBM per AEC Q100-002 4
ESD CDM V(ESD) -750 750 V CDM per AEC Q100-011 4
Input voltage VIN to PGND VIN 3.5 36 V 4
EN voltage EN -0.3 V max VIN 4
FB voltage FB -0.3 1.1 V 4
PGOOD voltage PGOOD -0.3 12 V 4
BIAS input not used BIAS -0.3 0.3 V 4
BIAS input used BIAS 3.3 28 V max VIN or 28 V, whichever is lower 4
AGND to PGND -0.1 0.1 V 4
Output voltage VOUT 1 28 V 4
Output current IOUT 0 0.5 A 4
Operating junction temperature TJ -40 125 °C 4
Junction-to-ambient thermal resistance RθJA 39.9 °C/W PWP 16 pins 5
Junction-to-case (top) thermal resistance RθJC(top) 26.9 °C/W 5
Junction-to-board thermal resistance RθJB 21.7 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 2.3 °C/W 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper The SW pin connecting to the inductor should be as short as possible, and just wide enough to carry the load current without excessive heating. Short, thick traces or copper pours (shapes) should be u 43

CAD (KiCad official)

  • Symbol: LM43600AQPWPRQ1
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lm43600aqpwprq1-etched.step / lm43600aqpwprq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm43600aqpwprq1.step / lm43600aqpwprq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (54 pp, sha256 af73d69576790700, retrieved 2026-11-02, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF