3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM392P
Texas Instruments · Special Purpose Amplifiers · PDIP-8
LM392P from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUTPUT A (Comparator) | output | Comparator output that sinks 6 mA minimum (VO ≥ 1.5 V) with 250 mV typical saturation voltage at 4 mA and is compatible with TTL and CMOS logic. |
| 2 | INVERTING INPUT A | input | Comparator inverting input with common-mode range of 0 V to V+ - 1.5 V, which should not go below -0.3 V and can go up to 32 V without damage. |
| 3 | NONINVERTING INPUT A | input | Comparator noninverting input with common-mode range of 0 V to V+ - 1.5 V, which should not go below -0.3 V and can go up to 32 V without damage. |
| 4 | GND | power_in | Ground, or the negative supply when operating from split supplies (dual supply ±1.5 V to ±16 V). |
| 5 | NONINVERTING INPUT B | input | Operational amplifier noninverting input with common-mode range of 0 V to V+ - 1.5 V that must not exceed the power-supply level or go below -0.3 V. |
| 6 | INVERTING INPUT B | input | Operational amplifier inverting input with common-mode range of 0 V to V+ - 1.5 V that must not exceed the power-supply level or go below -0.3 V. |
| 7 | OUTPUT B (Operational Amplifier) | output | Operational amplifier output with a swing of 0 V to V+ - 1.5 V (RL = 2 kΩ) and short-circuit current of about 40 mA to ground. |
| 8 | V+ | power_in | Positive supply, 3 V to 32 V single supply (absolute maximum 32 V), with about 600 µA supply current essentially independent of supply voltage. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| V+ supply voltage, single supply (recommended operating) | V+ | 3 | 32 | V | Single supply | 3 | |
| V+ supply voltage, dual supply (recommended operating, magnitude) | V+ | 1.5 | 16 | V | Dual supply, printed as ±1.5 V min and ±16 V max | 3 | |
| Operating free-air temperature | TA | 0 | 70 | °C | 3 | ||
| V+ supply voltage, single supply (absolute maximum) | V+ | 32 | V | Single supply | 3 | ||
| V+ supply voltage, dual supply (absolute maximum, magnitude) | V+ | 16 | V | Dual supply, printed as ±16 V | 3 | ||
| Differential input voltage (absolute maximum) | VID | 32 | V | 3 | |||
| Input voltage range (absolute maximum) | VIN | -0.3 | 32 | V | 3 | ||
| Input current (absolute maximum) | II | 50 | mA | VIN < -0.3 V | 3 | ||
| Lead temperature during soldering | Tlead | 260 | °C | 10 s maximum | 3 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 3 | ||
| Input offset voltage (max V+, 1.5 V is not numeric, max left null) | VIO | -5 | 2 | 5 | mV | At output switch point, VO ≈ 1.4 V; RS = 0 Ω; V+ = 5 V to 30 V; VCM = 0 V to (V+, 1.5 V); 25°C | 4 |
| Input offset voltage | VIO | -7 | 7 | mV | At output switch point, VO ≈ 1.4 V; RS = 0 Ω; V+ = 5 V to 30 V; VCM = 0 V to (V+, 1.5 V); 0°C to 70°C | 4 | |
| Input bias current | IIB | 50 | 205 | nA | IN(+) or IN(-), VCM = 0 V; 25°C | 4 | |
| Input bias current | IIB | 400 | nA | IN(+) or IN(-), VCM = 0 V; 0°C to 70°C | 4 | ||
| Input offset current | IIO | -50 | 5 | 50 | nA | IN(+), IN(-); 25°C | 4 |
| Input offset current | IIO | 150 | nA | IN(+), IN(-); 0°C to 70°C | 4 | ||
| Input common-mode voltage (max V+, 1.5 V, not numeric, max left null) | VCM | 0 | V | V+ = 30 V; 25°C | 4 | ||
| Input common-mode voltage (max V+, 2 V, not numeric, max left null) | VCM | 0 | V | V+ = 30 V; 0°C to 70°C | 4 | ||
| Supply current | I+ | 1 | 2 | mA | RL = ∞; V+ = 30 V; 0°C to 70°C | 4 | |
| Supply current | I+ | 0.5 | 1 | mA | RL = ∞; V+ = 5 V; 0°C to 70°C | 4 | |
| Differential input voltage | VDI | 32 | V | All VIN ≥ 0 V (or V-, if used); 0°C to 70°C | 4 | ||
| Large signal voltage gain | AVD | 25 | 100 | V/mV | V+ = 15 V, VO swing = 1 V to 11 V, RL = 2 kΩ; 25°C | 4 | |
| Output voltage swing (max V+, 1.5 V, not numeric, max left null) | VOS | 0 | V | RL = 2 kΩ; 25°C | 4 | ||
| Common-mode rejection ratio | CMRR | 65 | 70 | dB | VCM = 0 V to (V+, 1.5 V); 25°C | 4 | |
| Power-supply rejection ratio | kSVR | 65 | 100 | dB | 25°C | 4 | |
| Output source current | Isource | 20 | 40 | mA | VIN(+) = 1 V, VIN(-) = 0 V, V+ = 15 V, VO = 2 V; 25°C | 4 | |
| Output sink current | Isink | 10 | 20 | mA | VIN(-) = 1 V, VIN(+) = 0 V, VO = 2 V; 25°C | 4 | |
| Output sink current | Isink | 12 | 50 | µA | VIN(+) = 0 V, V+ = 15 V, VO = 200 mV; 25°C | 4 | |
| Voltage gain | VG | 50 | 200 | V/mV | RL ≥ 15 kΩ, V+ = 15 V; 25°C | 5 | |
| Output sink current | Isink | 6 | 16 | mA | VIN(-) = 1 V, VIN(+) = 0 V, VO ≥ 1.5 V; 25°C | 5 | |
| Saturation voltage | VS | 250 | 400 | mV | VIN(-) ≥ 1 V, VIN(+) = 0, ISINK ≤ 4 mA; 25°C | 5 | |
| Saturation voltage | VS | 700 | mV | VIN(-) ≥ 1 V, VIN(+) = 0, ISINK ≤ 4 mA; 0°C to 70°C | 5 | ||
| Output leakage current | ILO | 1 | µA | VIN(-) = 0, VIN(+) ≥ 1 V, VO = 30 V; 0°C to 70°C | 5 | ||
| Input offset voltage drift | αVIO | 7 | µV/°C | RS = 0 Ω; 0°C to 70°C | 4 | ||
| Input offset current drift | αIIO | 10 | pA/°C | RS = 0 Ω; 0°C to 70°C | 4 | ||
| Amplifier-to-amplifier coupling | -100 | dB | f = 1 kHz to 20 kHz, input referred; 25°C | 4 | |||
| Large signal response time | tLSR | 300 | ns | VIN = TTL logic swing, VREF = 1.4 V, VRL = 5 V, RL = 5.1 kΩ; 25°C | 5 | ||
| Response time | tR | 1.3 | µs | VRL = 5 V, RL = 5.1 kΩ; 25°C | 5 | ||
| Output leakage current | ILO | 0.1 | nA | VIN(-) = 0, VIN(+) ≥ 1 V, VO = 5 V; 25°C | 5 | ||
| Package thermal impedance, junction to free air (P package) | θJA | 84 | °C/W | P package; JESD 51-7 | 3 |
CAD (KiCad official)
- Symbol:
LM392P - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: PDIP-8 (KiCad packages3D, STEP)
- 3D model files:
lm392p-etched.step/lm392p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm392p.step/lm392p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (18 pp, sha256
1e05b6151689bd49, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).