main
Ray
Publish 0.1.0
cd3894f
LM3492HCQMHX
Texas Instruments · LED Drivers · HTSSOP-20-EP
LM3492HCQMHX from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input with an internal pullup that must be connected to a voltage higher than 1.63 V to provide precision enable. |
| 2 | VIN | power_in | Input supply voltage pin with an input voltage range from 4.5 V to 65 V. |
| 3 | SW | output | Switch node internally connected to the drain of the integrated MOSFET. |
| 4 | SW | output | Switch node internally connected to the drain of the integrated MOSFET. |
| 5 | VOUT | input | Output voltage sense pin that senses the output voltage for nearly constant switching frequency control. |
| 6 | RT | input | Frequency control pin where an external resistor from the VOUT pin to this pin sets the switching frequency. |
| 7 | FB | input | Output voltage feedback pin connected through a feedback resistor divider, with the voltage of this pin from 1.05 V to 2.5 V. |
| 8 | GND | power_in | Analog signal ground that must be connected to the exposed pad directly beneath the device. |
| 9 | IOUT2 | input | Current regulator input for channel 2 whose regulated current is programmable via the IREF pin. |
| 10 | IOUT1 | input | Current regulator input for channel 1 whose regulated current is programmable via the IREF pin. |
| 11 | CDHC | input | Dynamic headroom control pin where an external capacitor sets DHC sensitivity and a 12-µA internal source charges it for soft-start. |
| 12 | IREF | input | Current setting pin where an external resistor to ground programs the regulated current of channels 1 and 2. |
| 13 | COMM | bidirectional | Open-drain bidirectional logic communication pin used for indications and command sending with an external MCU. |
| 14 | LGND | power_in | Current regulator ground that must be connected to the GND pin and exposed pad, and is not internally connected to GND. |
| 15 | DIM1/CLK | bidirectional | Dimming control of channel 1 that is internally pulled low by 5 µA and also serves as the clock for latching COMM input and output data. |
| 16 | DIM2 | input | Dimming control of channel 2 that controls the on and off of the current regulator of channel 2 and is internally pulled low by 5 µA. |
| 17 | PGND | power_in | Integrated MOSFET ground that must be connected to the GND pin and exposed pad for normal operation and is not internally connected to GND. |
| 18 | PGND | power_in | Integrated MOSFET ground that must be connected to the GND pin and exposed pad for normal operation and is not internally connected to GND. |
| 19 | VCC | power_out | Internal LED regulator output nominally regulated to 5.5 V that requires a capacitor of 0.47 µF or larger between VCC and GND. |
| 20 | ILIM | input | Peak current limit adjust pin where a resistor from ILIM to VCC reduces the limit and connecting ILIM to ground gives the maximum limit. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN, RT, VOUT to GND, SW to GND | -0.3 | 67 | V | 4 | |||
| SW to GND transient | -2 | V | transient <100 ns | 4 | |||
| ILIM to GND | -0.3 | 1 | V | 4 | |||
| FB to GND | -0.3 | 5 | V | 4 | |||
| COMM, DIM1, DIM2 to GND | -0.3 | 6 | V | 4 | |||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Supply input voltage | VIN | 4.5 | 65 | V | 4 | ||
| Junction temperature operating | TJ | -40 | 125 | °C | 4 | ||
| VCC output voltage | VVCC | 4.7 | 5.5 | 6.3 | V | CVCC = 0.47 µF, no load | 5 |
| VCC pin undervoltage lockout threshold | VCC_UVLO | 3.56 | 3.78 | 4 | V | VVCC increasing, TA = TJ = 25°C | 5 |
| IIN operating current | IIN | 3.6 | 5.2 | mA | No switching, VFB = 0 V | 5 | |
| VCC pin current limit | IVCC | 30 | mA | VVCC = 0 V | 5 | ||
| VCC pin output voltage when supplied by VOUT | VCC-VOUT | 3.5 | 4.1 | 4.7 | V | VIN = Open, IVCC = 1 mA, VOUT = 18 V | 5 |
| EN pin input threshold | VEN | 1.55 | 1.63 | 1.71 | V | VEN rising | 5 |
| EN pin threshold hysteresis | VEN-HYS | 194 | mV | VEN falling | 5 | ||
| IREF pin voltage | VIREF | 1.231 | 1.256 | 1.281 | V | 4.5 V ≤ VIN ≤ 65 V | 5 |
| VIOUT under DHC | VDHC50 | 0.16 | 0.225 | 0.29 | V | IOUT = 50 mA, RIREF = 25 kΩ | 5 |
| VIOUT under DHC | VDHC100 | 0.38 | 0.48 | 0.58 | V | IOUT = 100 mA, RIREF = 12.5 kΩ | 5 |
| VIOUT under DHC | VDHC200 | 0.81 | 0.99 | 1.17 | V | IOUT = 200 mA, RIREF = 6.25 kΩ | 5 |
| VIOUT under DHC | VDHC250 | 0.81 | 1.21 | 1.44 | V | IOUT = 250 mA, RIREF = 5 kΩ | 5 |
| Current output under DHC | IOUT50 | 47.5 | 50 | 52.5 | mA | VIOUT = VDHC50, RIREF = 25 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT50 | 46.5 | 50 | 53.5 | mA | VIOUT = VDHC50, RIREF = 25 kΩ | 6 |
| Current output under DHC | IOUT100 | 97 | 100 | 103 | mA | VIOUT = VDHC100, RIREF = 12.5 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT100 | 96 | 100 | 104 | mA | VIOUT = VDHC100, RIREF = 12.5 kΩ | 6 |
| Current output under DHC | IOUT200 | 194 | 200 | 206 | mA | VIOUT = VDHC200, RIREF = 6.25 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT200 | 192 | 200 | 208 | mA | VIOUT = VDHC200, RIREF = 6.25 kΩ | 6 |
| Current output under DHC | IOUT250 | 241.3 | 250 | 258.8 | mA | VIOUT = VDHC250, RIREF = 5 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT250 | 238 | 250 | 262 | mA | VIOUT = VDHC250, RIREF = 5 kΩ | 6 |
| Leakage at maximum work voltage | IOUTOFF | 5 | µA | VDIM = 0, VIOUT = 65 V | 6 | ||
| Minimum work voltage | VIOUT50-MIN | 0.1 | 0.15 | V | IOUT = 50 mA, RIREF = 25 kΩ, IOUT = 0.98 × IOUT50, TA = TJ = 25°C | 6 | |
| Minimum work voltage | VIOUT100-MIN | 0.2 | 0.35 | V | IOUT = 100 mA, RIREF = 12.5 kΩ, IOUT = 0.98 × IOUT100, TA = TJ = 25°C | 6 | |
| Minimum work voltage | VIOUT200-MIN | 0.4 | 0.65 | V | IOUT = 200 mA, RIREF = 6.25 kΩ, IOUT = 0.98 × IOUT200, TA = TJ = 25°C | 6 | |
| Minimum work voltage | VIOUT250-MIN | 0.5 | 0.82 | V | IOUT = 250 mA, RIREF = 5 kΩ, IOUT = 0.98 × IOUT250, TA = TJ = 25°C | 6 | |
| DIM voltage HIGH | VDIM-HIGH | 1.17 | V | 6 | |||
| DIM voltage LOW | VDIM-LOW | 0.7 | V | 6 | |||
| CDHC pin pullup current | ICDHC-PULLUP | 10 | 200 | 500 | nA | DIM = Low, VCDHC = 2.3 V, VFB = 3 V | 6 |
| Integrated MOSFET peak current limit threshold | ICL-MAX | 3.3 | 3.9 | 4.5 | A | 6 | |
| Integrated MOSFET On-resistance | RDS(on) | 0.19 | 0.43 | Ω | ISW = 500 mA | 6 | |
| FB pin overvoltage protection threshold | VFB-OVP | 2.64 | 2.76 | 2.88 | V | VFB rising, VCDHC = 4 V | 6 |
| FB pin OVP hysteresis | VFB-OVP | 0.1 | 0.215 | 0.323 | V | VFB falling | 6 |
| COMM pin IOUT overvoltage threshold | VIOUT-OV | 5.6 | 6.7 | 7.8 | V | COMM goes LOW during VIOUT rising, other VIOUT = 1.2 V | 7 |
| COMM pin at LOW | VCOMM-LOW | 0.7 | V | 5 mA into COMM | 7 | ||
| COMM pin open leakage | ILEAK-FAULT | 5 | µA | VCOMM = 5 V | 7 | ||
| Thermal shutdown temperature | TSD | 165 | °C | TJ rising | 7 | ||
| Overtemperature indication | TOTM | 135 | °C | TJ rising | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 36.8 | °C/W | PWP package | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 21.8 | °C/W | PWP package | 5 | ||
| Junction-to-board thermal resistance | RθJB | 18.3 | °C/W | PWP package | 5 | ||
| VCC pin UVLO hysteresis | VCC_UVLO-HYS | 310 | mV | VVCC decreasing, TA = TJ = 25°C | 5 | ||
| IIN operating current, device shutdown | IIN-SD | 30 | 95 | µA | VEN = 0 V | 5 | |
| Enable pullup current at shutdown | IEN-SHUT | 2 | µA | VEN = 0 V | 5 | ||
| Enable pullup current during operation | IEN-OPER | 40 | µA | VEN = 2 V | 5 | ||
| CDHC pin source current | ICDHC-SRC | 60 | µA | VCDHC = 1.6 V, VFB = 3 V, VIOUT = 0 V, DIM = High | 6 | ||
| CDHC pin sink current | ICDHC-SINK | 56 | µA | VCDHC = 1.6 V, VFB = 3 V, VIOUT = 3 V, DIM = High | 6 | ||
| Power-Good FB pin threshold | VFBTH-PWRGD | 2.25 | V | 6 | |||
| Feedback pin input current | IFB | 1 | µA | VFB = 3 V | 6 | ||
| ON timer pulse width | tON | 1460 | ns | VIN = 12 V, VOUT = 65 V, RRT = 300 kΩ | 6 | ||
| ON timer pulse width | tON | 800 | ns | VIN = 24 V, VOUT = 32.5 V, RRT = 300 kΩ | 6 | ||
| ON timer pulse width | tON | 550 | ns | VIN = 12 V, VOUT = 65 V, RRT = 100 kΩ | 6 | ||
| ON timer pulse width | tON | 350 | ns | VIN = 24 V, VOUT = 32.5 V, RRT = 100 kΩ | 6 | ||
| OFF timer pulse width | tOFF | 145 | 350 | ns | 6 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | capacitor COUT. The ground plane connecting the GND, PGND, and LGND pins and the exposed pad of the device and the ground connection of the CIN and COUT should be placed on the same copper layer. | 22 |
CAD (KiCad official)
- Symbol:
LM3492HCQMHX - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP (KiCad packages3D, STEP)
- 3D model files:
lm3492hcqmhx-etched.step/lm3492hcqmhx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm3492hcqmhx.step/lm3492hcqmhx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (32 pp, sha256
b811134d80539a7d, retrieved 2026-11-21) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM3492HCQMHX
**Texas Instruments** · LED Drivers · HTSSOP-20-EP
LM3492HCQMHX from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input with an internal pullup that must be connected to a voltage higher than 1.63 V to provide precision enable. |
| 2 | VIN | power_in | Input supply voltage pin with an input voltage range from 4.5 V to 65 V. |
| 3 | SW | output | Switch node internally connected to the drain of the integrated MOSFET. |
| 4 | SW | output | Switch node internally connected to the drain of the integrated MOSFET. |
| 5 | VOUT | input | Output voltage sense pin that senses the output voltage for nearly constant switching frequency control. |
| 6 | RT | input | Frequency control pin where an external resistor from the VOUT pin to this pin sets the switching frequency. |
| 7 | FB | input | Output voltage feedback pin connected through a feedback resistor divider, with the voltage of this pin from 1.05 V to 2.5 V. |
| 8 | GND | power_in | Analog signal ground that must be connected to the exposed pad directly beneath the device. |
| 9 | IOUT2 | input | Current regulator input for channel 2 whose regulated current is programmable via the IREF pin. |
| 10 | IOUT1 | input | Current regulator input for channel 1 whose regulated current is programmable via the IREF pin. |
| 11 | CDHC | input | Dynamic headroom control pin where an external capacitor sets DHC sensitivity and a 12-µA internal source charges it for soft-start. |
| 12 | IREF | input | Current setting pin where an external resistor to ground programs the regulated current of channels 1 and 2. |
| 13 | COMM | bidirectional | Open-drain bidirectional logic communication pin used for indications and command sending with an external MCU. |
| 14 | LGND | power_in | Current regulator ground that must be connected to the GND pin and exposed pad, and is not internally connected to GND. |
| 15 | DIM1/CLK | bidirectional | Dimming control of channel 1 that is internally pulled low by 5 µA and also serves as the clock for latching COMM input and output data. |
| 16 | DIM2 | input | Dimming control of channel 2 that controls the on and off of the current regulator of channel 2 and is internally pulled low by 5 µA. |
| 17 | PGND | power_in | Integrated MOSFET ground that must be connected to the GND pin and exposed pad for normal operation and is not internally connected to GND. |
| 18 | PGND | power_in | Integrated MOSFET ground that must be connected to the GND pin and exposed pad for normal operation and is not internally connected to GND. |
| 19 | VCC | power_out | Internal LED regulator output nominally regulated to 5.5 V that requires a capacitor of 0.47 µF or larger between VCC and GND. |
| 20 | ILIM | input | Peak current limit adjust pin where a resistor from ILIM to VCC reduces the limit and connecting ILIM to ground gives the maximum limit. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN, RT, VOUT to GND, SW to GND | | -0.3 | | 67 | V | | 4 |
| SW to GND transient | | -2 | | | V | transient <100 ns | 4 |
| ILIM to GND | | -0.3 | | 1 | V | | 4 |
| FB to GND | | -0.3 | | 5 | V | | 4 |
| COMM, DIM1, DIM2 to GND | | -0.3 | | 6 | V | | 4 |
| Junction temperature | TJ | | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| Supply input voltage | VIN | 4.5 | | 65 | V | | 4 |
| Junction temperature operating | TJ | -40 | | 125 | °C | | 4 |
| VCC output voltage | VVCC | 4.7 | 5.5 | 6.3 | V | CVCC = 0.47 µF, no load | 5 |
| VCC pin undervoltage lockout threshold | VCC_UVLO | 3.56 | 3.78 | 4 | V | VVCC increasing, TA = TJ = 25°C | 5 |
| IIN operating current | IIN | | 3.6 | 5.2 | mA | No switching, VFB = 0 V | 5 |
| VCC pin current limit | IVCC | | 30 | | mA | VVCC = 0 V | 5 |
| VCC pin output voltage when supplied by VOUT | VCC-VOUT | 3.5 | 4.1 | 4.7 | V | VIN = Open, IVCC = 1 mA, VOUT = 18 V | 5 |
| EN pin input threshold | VEN | 1.55 | 1.63 | 1.71 | V | VEN rising | 5 |
| EN pin threshold hysteresis | VEN-HYS | | 194 | | mV | VEN falling | 5 |
| IREF pin voltage | VIREF | 1.231 | 1.256 | 1.281 | V | 4.5 V ≤ VIN ≤ 65 V | 5 |
| VIOUT under DHC | VDHC50 | 0.16 | 0.225 | 0.29 | V | IOUT = 50 mA, RIREF = 25 kΩ | 5 |
| VIOUT under DHC | VDHC100 | 0.38 | 0.48 | 0.58 | V | IOUT = 100 mA, RIREF = 12.5 kΩ | 5 |
| VIOUT under DHC | VDHC200 | 0.81 | 0.99 | 1.17 | V | IOUT = 200 mA, RIREF = 6.25 kΩ | 5 |
| VIOUT under DHC | VDHC250 | 0.81 | 1.21 | 1.44 | V | IOUT = 250 mA, RIREF = 5 kΩ | 5 |
| Current output under DHC | IOUT50 | 47.5 | 50 | 52.5 | mA | VIOUT = VDHC50, RIREF = 25 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT50 | 46.5 | 50 | 53.5 | mA | VIOUT = VDHC50, RIREF = 25 kΩ | 6 |
| Current output under DHC | IOUT100 | 97 | 100 | 103 | mA | VIOUT = VDHC100, RIREF = 12.5 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT100 | 96 | 100 | 104 | mA | VIOUT = VDHC100, RIREF = 12.5 kΩ | 6 |
| Current output under DHC | IOUT200 | 194 | 200 | 206 | mA | VIOUT = VDHC200, RIREF = 6.25 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT200 | 192 | 200 | 208 | mA | VIOUT = VDHC200, RIREF = 6.25 kΩ | 6 |
| Current output under DHC | IOUT250 | 241.3 | 250 | 258.8 | mA | VIOUT = VDHC250, RIREF = 5 kΩ, TA = TJ = 25°C | 6 |
| Current output under DHC | IOUT250 | 238 | 250 | 262 | mA | VIOUT = VDHC250, RIREF = 5 kΩ | 6 |
| Leakage at maximum work voltage | IOUTOFF | | | 5 | µA | VDIM = 0, VIOUT = 65 V | 6 |
| Minimum work voltage | VIOUT50-MIN | | 0.1 | 0.15 | V | IOUT = 50 mA, RIREF = 25 kΩ, IOUT = 0.98 × IOUT50, TA = TJ = 25°C | 6 |
| Minimum work voltage | VIOUT100-MIN | | 0.2 | 0.35 | V | IOUT = 100 mA, RIREF = 12.5 kΩ, IOUT = 0.98 × IOUT100, TA = TJ = 25°C | 6 |
| Minimum work voltage | VIOUT200-MIN | | 0.4 | 0.65 | V | IOUT = 200 mA, RIREF = 6.25 kΩ, IOUT = 0.98 × IOUT200, TA = TJ = 25°C | 6 |
| Minimum work voltage | VIOUT250-MIN | | 0.5 | 0.82 | V | IOUT = 250 mA, RIREF = 5 kΩ, IOUT = 0.98 × IOUT250, TA = TJ = 25°C | 6 |
| DIM voltage HIGH | VDIM-HIGH | 1.17 | | | V | | 6 |
| DIM voltage LOW | VDIM-LOW | | | 0.7 | V | | 6 |
| CDHC pin pullup current | ICDHC-PULLUP | 10 | 200 | 500 | nA | DIM = Low, VCDHC = 2.3 V, VFB = 3 V | 6 |
| Integrated MOSFET peak current limit threshold | ICL-MAX | 3.3 | 3.9 | 4.5 | A | | 6 |
| Integrated MOSFET On-resistance | RDS(on) | | 0.19 | 0.43 | Ω | ISW = 500 mA | 6 |
| FB pin overvoltage protection threshold | VFB-OVP | 2.64 | 2.76 | 2.88 | V | VFB rising, VCDHC = 4 V | 6 |
| FB pin OVP hysteresis | VFB-OVP | 0.1 | 0.215 | 0.323 | V | VFB falling | 6 |
| COMM pin IOUT overvoltage threshold | VIOUT-OV | 5.6 | 6.7 | 7.8 | V | COMM goes LOW during VIOUT rising, other VIOUT = 1.2 V | 7 |
| COMM pin at LOW | VCOMM-LOW | | | 0.7 | V | 5 mA into COMM | 7 |
| COMM pin open leakage | ILEAK-FAULT | | | 5 | µA | VCOMM = 5 V | 7 |
| Thermal shutdown temperature | TSD | | | 165 | °C | TJ rising | 7 |
| Overtemperature indication | TOTM | | | 135 | °C | TJ rising | 7 |
| Junction-to-ambient thermal resistance | RθJA | | 36.8 | | °C/W | PWP package | 5 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 21.8 | | °C/W | PWP package | 5 |
| Junction-to-board thermal resistance | RθJB | | 18.3 | | °C/W | PWP package | 5 |
| VCC pin UVLO hysteresis | VCC_UVLO-HYS | | 310 | | mV | VVCC decreasing, TA = TJ = 25°C | 5 |
| IIN operating current, device shutdown | IIN-SD | | 30 | 95 | µA | VEN = 0 V | 5 |
| Enable pullup current at shutdown | IEN-SHUT | | 2 | | µA | VEN = 0 V | 5 |
| Enable pullup current during operation | IEN-OPER | | 40 | | µA | VEN = 2 V | 5 |
| CDHC pin source current | ICDHC-SRC | | 60 | | µA | VCDHC = 1.6 V, VFB = 3 V, VIOUT = 0 V, DIM = High | 6 |
| CDHC pin sink current | ICDHC-SINK | | 56 | | µA | VCDHC = 1.6 V, VFB = 3 V, VIOUT = 3 V, DIM = High | 6 |
| Power-Good FB pin threshold | VFBTH-PWRGD | | 2.25 | | V | | 6 |
| Feedback pin input current | IFB | | 1 | | µA | VFB = 3 V | 6 |
| ON timer pulse width | tON | | 1460 | | ns | VIN = 12 V, VOUT = 65 V, RRT = 300 kΩ | 6 |
| ON timer pulse width | tON | | 800 | | ns | VIN = 24 V, VOUT = 32.5 V, RRT = 300 kΩ | 6 |
| ON timer pulse width | tON | | 550 | | ns | VIN = 12 V, VOUT = 65 V, RRT = 100 kΩ | 6 |
| ON timer pulse width | tON | | 350 | | ns | VIN = 24 V, VOUT = 32.5 V, RRT = 100 kΩ | 6 |
| OFF timer pulse width | tOFF | 145 | | 350 | ns | | 6 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | capacitor COUT. The ground plane connecting the GND, PGND, and LGND pins and the exposed pad of the device and the ground connection of the CIN and COUT should be placed on the same copper layer. | 22 |
## CAD (KiCad official)
- Symbol: `LM3492HCQMHX`
- Footprint: `Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm`
- 3D model: HTSSOP-20-EP (KiCad packages3D, STEP)
- 3D model files: `lm3492hcqmhx-etched.step` / `lm3492hcqmhx-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm3492hcqmhx.step` / `lm3492hcqmhx.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm3492hc.pdf) (32 pp, sha256 `b811134d80539a7d`, retrieved 2026-11-21)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm3492hcqmhx-datasheet.pdf)