main
Ray
Publish 0.1.0
106b892
LM3431MHX
Texas Instruments · LED Drivers · HTSSOP-28-EP
LM3431MHX from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power supply input, recommended operating range 4.5 V to 36 V (absolute maximum -0.3 V to 37 V). |
| 2 | PGND | power_in | Power ground pin; connect to ground. |
| 3 | VCC | power_out | Internal reference voltage output (4.80 V to 5.24 V at 25 mA load); bypass to PGND with a minimum 4.7 µF capacitor. |
| 4 | LG | output | Boost controller gate drive output; connect to the NFET gate. |
| 5 | CS | input | Boost controller current sense pin; connect to the top side of the boost current sense resistor (absolute maximum -0.3 V to 7 V). |
| 6 | ILIM | passive | Boost controller current limit adjust; connect a resistor from this pin to the boost current sense resistor to set the current limit threshold. |
| 7 | MODE/F | input | Dimming mode selection; pull high for digital PWM control, or connect a capacitor to GND to set the internal dimming frequency (absolute maximum -0.3 V to 7 V). |
| 8 | FF | passive | Feedforward pin; connect a resistor to ground to control output over/undershoot during PWM dimming. |
| 9 | RT | passive | Frequency adjust pin; connect a resistor from this pin to ground to set the boost controller operating frequency (adjustable up to 1 MHz). |
| 10 | REF | power_out | Reference voltage output (2.45 V to 2.55 V, 2.5 V typical at IREF < 300 µA) used to provide the REFIN voltage. |
| 11 | REFIN | input | Sets the LED current feedback voltage; connect to a resistor divider from the REF pin (absolute maximum -0.3 V to 7 V). |
| 12 | COMP | output | Output of the error amplifier; connect to the compensation network. |
| 13 | SGND | power_in | Signal ground pin; connect to ground. |
| 14 | AFB | input | Anode feedback pin for boost voltage feedback during LED off time; connect to a resistor divider from the output voltage (absolute maximum -0.3 V to 7 V). |
| 15 | SS/SH | passive | Soft-start and sample-hold pin; connect a capacitor from this pin to ground to set the soft-start time. |
| 16 | DLY | passive | Fault delay pin; connect a capacitor from this pin to ground to set the shutdown delay time. |
| 17 | CFB | input | Cathode feedback pin for boost voltage feedback; connect through a diode to the bottom cathode of each LED string (absolute maximum -0.3 V to 7 V). |
| 18 | SC | input | LED short circuit detection pin; connect through a diode to the bottom cathode of each string (absolute maximum -0.3 V to 40 V). |
| 19 | LEDOFF | bidirectional | Dual-function pin: controls external drivers during PWM dimming, or connect to ground to enable automatic fault restart. |
| 20 | SNS3 | input | Current feedback for channel 3; connect to the top of the channel 3 current sense resistor (absolute maximum -0.3 V to 7 V). |
| 21 | NDRV3 | output | Base drive for the channel 3 current regulator; connect to the NPN base or NFET gate. |
| 22 | SNS2 | input | Current feedback for channel 2 (absolute maximum -0.3 V to 7 V). |
| 23 | NDRV2 | output | Base drive for the channel 2 current regulator; connect to the NPN base or NFET gate. |
| 24 | SNS1 | input | Current feedback for channel 1 (absolute maximum -0.3 V to 7 V). |
| 25 | NDRV1 | output | Base drive for the channel 1 current regulator; connect to the NPN base or NFET gate. |
| 26 | THM | input | LED thermal monitor input; when pulled below 1.2 V the device enters standby mode (absolute maximum -0.3 V to 7 V). |
| 27 | DIM | input | PWM dimming input accepting a digital PWM or analog voltage level to control LED current duty cycle (absolute maximum -0.3 V to 7 V). |
| 28 | EN | input | Enable pin; connect to VIN through a resistor divider to set an external UVLO threshold, pull low to shut down (absolute maximum -0.3 V to 10 V). |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 29 |
CAD (KiCad official)
- Symbol:
LM3431MHX - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
lm3431mhx-etched.step/lm3431mhx-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm3431mhx.step/lm3431mhx.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
577125aea071ac7f, retrieved 2026-10-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LM3431MHX
**Texas Instruments** · LED Drivers · HTSSOP-28-EP
LM3431MHX from Texas Instruments, in a HTSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power supply input, recommended operating range 4.5 V to 36 V (absolute maximum -0.3 V to 37 V). |
| 2 | PGND | power_in | Power ground pin; connect to ground. |
| 3 | VCC | power_out | Internal reference voltage output (4.80 V to 5.24 V at 25 mA load); bypass to PGND with a minimum 4.7 µF capacitor. |
| 4 | LG | output | Boost controller gate drive output; connect to the NFET gate. |
| 5 | CS | input | Boost controller current sense pin; connect to the top side of the boost current sense resistor (absolute maximum -0.3 V to 7 V). |
| 6 | ILIM | passive | Boost controller current limit adjust; connect a resistor from this pin to the boost current sense resistor to set the current limit threshold. |
| 7 | MODE/F | input | Dimming mode selection; pull high for digital PWM control, or connect a capacitor to GND to set the internal dimming frequency (absolute maximum -0.3 V to 7 V). |
| 8 | FF | passive | Feedforward pin; connect a resistor to ground to control output over/undershoot during PWM dimming. |
| 9 | RT | passive | Frequency adjust pin; connect a resistor from this pin to ground to set the boost controller operating frequency (adjustable up to 1 MHz). |
| 10 | REF | power_out | Reference voltage output (2.45 V to 2.55 V, 2.5 V typical at IREF < 300 µA) used to provide the REFIN voltage. |
| 11 | REFIN | input | Sets the LED current feedback voltage; connect to a resistor divider from the REF pin (absolute maximum -0.3 V to 7 V). |
| 12 | COMP | output | Output of the error amplifier; connect to the compensation network. |
| 13 | SGND | power_in | Signal ground pin; connect to ground. |
| 14 | AFB | input | Anode feedback pin for boost voltage feedback during LED off time; connect to a resistor divider from the output voltage (absolute maximum -0.3 V to 7 V). |
| 15 | SS/SH | passive | Soft-start and sample-hold pin; connect a capacitor from this pin to ground to set the soft-start time. |
| 16 | DLY | passive | Fault delay pin; connect a capacitor from this pin to ground to set the shutdown delay time. |
| 17 | CFB | input | Cathode feedback pin for boost voltage feedback; connect through a diode to the bottom cathode of each LED string (absolute maximum -0.3 V to 7 V). |
| 18 | SC | input | LED short circuit detection pin; connect through a diode to the bottom cathode of each string (absolute maximum -0.3 V to 40 V). |
| 19 | LEDOFF | bidirectional | Dual-function pin: controls external drivers during PWM dimming, or connect to ground to enable automatic fault restart. |
| 20 | SNS3 | input | Current feedback for channel 3; connect to the top of the channel 3 current sense resistor (absolute maximum -0.3 V to 7 V). |
| 21 | NDRV3 | output | Base drive for the channel 3 current regulator; connect to the NPN base or NFET gate. |
| 22 | SNS2 | input | Current feedback for channel 2 (absolute maximum -0.3 V to 7 V). |
| 23 | NDRV2 | output | Base drive for the channel 2 current regulator; connect to the NPN base or NFET gate. |
| 24 | SNS1 | input | Current feedback for channel 1 (absolute maximum -0.3 V to 7 V). |
| 25 | NDRV1 | output | Base drive for the channel 1 current regulator; connect to the NPN base or NFET gate. |
| 26 | THM | input | LED thermal monitor input; when pulled below 1.2 V the device enters standby mode (absolute maximum -0.3 V to 7 V). |
| 27 | DIM | input | PWM dimming input accepting a digital PWM or analog voltage level to control LED current duty cycle (absolute maximum -0.3 V to 7 V). |
| 28 | EN | input | Enable pin; connect to VIN through a resistor divider to set an external UVLO threshold, pull low to shut down (absolute maximum -0.3 V to 10 V). |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-28-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 29 |
## CAD (KiCad official)
- Symbol: `LM3431MHX`
- Footprint: `Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm`
- 3D model: HTSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files: `lm3431mhx-etched.step` / `lm3431mhx-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm3431mhx.step` / `lm3431mhx.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm3431) (40 pp, sha256 `577125aea071ac7f`, retrieved 2026-10-11, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lm3431mhx-datasheet.pdf)