main
Ray lm3150mhx: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) 62aede0
{
  "schema_version": 1,
  "type": "component",
  "slug": "lm3150mhx",
  "title": "LM3150MHX",
  "brief": "Texas Instruments DC-DC Converters, HTSSOP-14-EP. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.2.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "pmic",
    "lm3150mhx"
  ],
  "component": {
    "mpn": "LM3150MHX",
    "manufacturer": "Texas Instruments",
    "package": "HTSSOP-14-EP",
    "pin_count": 15,
    "category": "PMIC",
    "subcategory": "DC-DC Converters",
    "datasheet": "https://www.ti.com/lit/ds/symlink/lm3150mhx.pdf",
    "parts": {
      "symbol": "lm3150mhx.kicad_sym",
      "footprint": "lm3150mhx.kicad_mod",
      "model_3d": "lm3150mhx-etched.glb",
      "model_3d_plain": "lm3150mhx.glb",
      "model_3d_step": "lm3150mhx-etched.step",
      "model_3d_step_plain": "lm3150mhx.step",
      "lbr": "lm3150mhx.lbr"
    },
    "distributor_links": {},
    "pins": [
      {
        "number": "1",
        "name": "VCC",
        "type": "power_out",
        "description": "Internal LDO output supplying the FET gate drivers and internal bias. Nominally regulated to 5.95 V. Connect a 1.0 µF to 4.7 µF decoupling capacitor from this pin to ground."
      },
      {
        "number": "2",
        "name": "VIN",
        "type": "power_in",
        "description": "Input supply pin to the device. Nominal input voltage range is 6 V to 42 V (abs max 47 V)."
      },
      {
        "number": "3",
        "name": "EN",
        "type": "input",
        "description": "Enable input. Apply a logic-high signal greater than 1.26 V (typ) to enable the IC, or leave floating. Ground this pin to disable the controller. Recommended operating range 0 V to 5 V."
      },
      {
        "number": "4",
        "name": "FB",
        "type": "input",
        "description": "Feedback input to the regulation, overvoltage, and short-circuit comparators. Regulation setting is 0.6 V. Connect to a feedback resistor divider from the output to set VOUT."
      },
      {
        "number": "5",
        "name": "SGND",
        "type": "power_in",
        "description": "Signal ground for all internal bias and reference circuitry. Should be tied to PGND at a single point. Pin 5 and pin 9 are both SGND and must be connected together."
      },
      {
        "number": "6",
        "name": "SS",
        "type": "passive",
        "description": "Soft-start capacitor node. An internal 7.7 µA current source charges an external capacitor from this pin to ground to program the output ramp rate at start-up."
      },
      {
        "number": "7",
        "name": "RON",
        "type": "input",
        "description": "On-time programming pin. An external resistor from VIN to this pin sets the high-side switch on-time and therefore the switching frequency."
      },
      {
        "number": "8",
        "name": "ILIM",
        "type": "input",
        "description": "Current-limit sense input. Monitors the low-side FET current and triggers current-limit operation when the inductor valley current exceeds the threshold set by R_LIM and the 85 µA (typ) I_LIM-TH sense current sourced from this pin."
      },
      {
        "number": "9",
        "name": "SGND",
        "type": "power_in",
        "description": "Signal ground (second connection). Tie to PGND at a single point. Must be connected to pin 5."
      },
      {
        "number": "10",
        "name": "SW",
        "type": "power_in",
        "description": "Switch node. Connection to the source of the high-side NMOS and drain of the low-side NMOS, and lower supply rail for the high-side gate driver. Boost capacitor (BST) is referenced to this pin. Abs max −3 V to 47 V."
      },
      {
        "number": "11",
        "name": "HG",
        "type": "output",
        "description": "High-side NMOS gate drive output. Driver is supplied by the differential voltage between BST and SW (typically ~5.95 V bootstrap rail)."
      },
      {
        "number": "12",
        "name": "BST",
        "type": "power_in",
        "description": "Bootstrap capacitor connection. Connect a 0.33 µF to 0.47 µF capacitor from SW to this pin. An internal diode charges the cap during the high-side off-time. Do not connect to an external supply rail. Abs max BST-SW 7 V; BST-GND 52 V."
      },
      {
        "number": "13",
        "name": "LG",
        "type": "output",
        "description": "Low-side NMOS gate drive output. Driver upper rail is supplied by VCC (~5.95 V)."
      },
      {
        "number": "14",
        "name": "PGND",
        "type": "power_in",
        "description": "Power ground; source connection for the synchronous low-side MOSFET driver. Tie to the power ground plane and to SGND at a single point."
      },
      {
        "number": "EP",
        "name": "EP",
        "type": "passive",
        "description": "Exposed die-attach thermal pad. Connect directly to SGND and to the PCB ground plane for heat dissipation."
      }
    ],
    "provenance": {
      "extractor": "ds2sf",
      "datasheet": {
        "url": "https://www.ti.com/lit/ds/symlink/lm3150mhx.pdf",
        "pages": 32,
        "sha256": "262f4efa528d8294",
        "source_tier": "mfr"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 15,
        "described": 15,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "lm3150mhx.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          7.35,
          5,
          1.05
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "e73930af88609deacee2bde98223bb9da2411f0cebb494015de765f0df216789",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "lm3150mhx-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          7.35,
          5,
          1.05
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "e400e731340c46c2f8b3d326437805d4c061b5d5bea01ccb6274599e7dedd376",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Texas Instruments",
      "Package": "HTSSOP-14-EP",
      "Category": "PMIC",
      "Pins": "15"
    }
  },
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "lm3150mhx"
  ],
  "discovery_pitch": "LM3150MHX (Texas Instruments) component page with datasheet-verified CAD.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "lm3150mhx.kicad_sym",
    "lm3150mhx.kicad_mod",
    "lm3150mhx.glb",
    "lm3150mhx.step",
    "lm3150mhx-etched.step",
    "lm3150mhx.lbr",
    "docs/hero.png",
    "docs/lm3150mhx-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  },
  "variants": [
    {
      "mpn": "LM3150MHX",
      "kind": "packaging"
    }
  ],
  "updated_at": "2026-09-28T16:32:54.594Z"
}