Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM29152RS

HTC Korea TAEJIN Tech · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · TO-252-5

LM29152RS from HTC Korea TAEJIN Tech, in a TO-252-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 EN input Chip enable input. Logic high (VEN >= 2.4 V) turns the regulator on; logic low (VEN <= 0.8 V) puts the device in zero-current shutdown (IOUT typ 10 uA, max 500 uA at VIN <= 26 V). May be tied to VIN if ON/OFF control is not required. Absolute max VEN = -20 V to +60 V; recommended operating -/+26 V.
2 VIN power_in Input supply. Recommended operating range up to +26 V; absolute max -20 V to +60 V (60 V limited to <100 ms, <=1% duty). Bypass with an input capacitor (CIN) close to the pin.
3 GND power_in Device ground / return. Ground pin current is typ 8 mA at IO = 750 mA and typ 22 mA at IO = 1.5 A (max 20 mA at 750 mA per data). Also serves as the thermal reference for the exposed tab.
4 VOUT power_out Regulated output. Delivers up to 1.5 A with 350 mV (typ) full-load dropout. On the adjustable LM29152 the output voltage is set by an external divider: VOUT = VREF x (1 + R1/R2), VREF = 1.24 V typ (1.215 - 1.265 V). Current limit typ 2.1 A (max 3.5 A). Requires an output capacitor (COUT) for stability.
5 ADJ input Adjust pin for the LM29152 adjustable variant (this pin is labeled FLG/ADJ in the shared pinout table; on LM29152 it is the ADJ feedback input, on LM29151 it is the FLG error-flag open-drain output). Connect to the R1/R2 divider tap from VOUT to GND to program VOUT = 1.24 V x (1 + R1/R2). Adjust-pin bias current is typ 40 nA (max 80 nA).
6 GND power_in Package tab (pad 6). the sheet does not name the tab's net; centre lead's net per the package (TO-263/TO-252 tab and centre lead are one piece of lead frame; task master ruling 2026-11-17): pin 3 is GND.

Key specifications

Parameter Value
Manufacturer HTC Korea TAEJIN Tech
Package TO-252-5
Category PMIC
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (IO = 10mA) VOUT -1 1 % IO = 10mA 6
Output Voltage (10mA≤IO≤IFL) VOUT -2 2 % 10mA≤IO≤ IFL, (VOUT+1V)≤VIN≤26V (Note 2) 6
Line Regulation ΔVLINE 0.06 0.5 % IO = 10mA, (VOUT+1V)≤VIN≤26V 6
Load Regulation ΔVLOAD 0.2 1 % VIN=VOUT+5V, 10mA≤IOUT≤IFULLOAD (Note 2,6) 6
Output Voltage Temp. Coefficient ΔVo/ΔT 20 100 ppm/℃ Note 6 6
Dropout Voltage at IO = 100mA VDO 80 200 mV ΔVOUT = -1%, (Note 3), IO = 100mA 6
Dropout Voltage at IO = 750mA VDO 220 mV ΔVOUT = -1%, (Note 3), IO = 750mA 6
Dropout Voltage at IO = 1.5A VDO 350 600 mV ΔVOUT = -1%, (Note 3), IO = 1.5A 6
Ground Current at IO = 750mA IGND 8 22 mA IO = 750mA, VIN = VOUT+1V 6
Ground Current at IO = 1.5A IGND 20 mA IO = 1.5A 6
Reference Voltage VREF 1.215 1.24 1.265 V Bold values guaranteed across operating temperature range 7
Reference Voltage (Note 8) VREF 1.203 1.277 V Note 8: VREF ≤ VOUT ≤ (VIN -1V), 2.3V ≤ VIN ≤ 26V, 10mA < IL < IFL, TJ < TJ Max. 7
Adjust Pin Bias Current IADJ 40 80 120 nA 7
Enable Input Voltage Logic High (On) VEN 2.4 V Logic High (On) 7
Enable Input Voltage Logic Low (Off) VEN 0.8 V Logic Low (Off) 7
Enable Pin Input Current IEN 100 600 750 μA VEN = 26V 7
Enable Pin Input Current IEN 2.5 5 μA VEN = 0.8V 7
Regulator Output Current in Shutdown 10 500 μA Note 10: VEN ≤ 0.8V and VIN ≤ 26V, VOUT = 0 7
Operating Input Voltage VIN 26 V 2
Operating Enable Input Voltage VEN 26 V 2
Junction Temperature TJ -40 125 ℃ 2
Input Supply Voltage VIN -20 60 V Note 1: maximum 60V must be of limited duration (<100msec) and duty cycle (≤1%); maximum continuous supply 26V 1
Enable Input Voltage VEN -20 60 V Note 1 1
Lead Temperature (Soldering) TSOL 260 ℃ Soldering, 5 sec 1
Storage Temperature Range TSTG -65 150 ℃ 1
Reference Voltage Temp. Coefficient 20 ppm/℃ Note 7 7
Adjust Pin Bias Current Temp. Coefficient 0.1 nA/℃ 7

CAD (KiCad official)

  • Symbol: LM29152RS
  • Footprint: Package_TO_SOT_SMD:TO-252-5_TabPin6
  • 3D model: TO-252-5 (KiCad packages3D, STEP)
  • 3D model files: lm29152rs-etched.step / lm29152rs-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm29152rs.step / lm29152rs.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: HTC Korea TAEJIN Tech datasheet (12 pp, sha256 edf268513dcf5ffe, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF