main
Ray lm26480sqx-aa: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) 113cd59
{
  "slug": "lm26480sqx-aa",
  "version": "0.1.0",
  "type": "component",
  "description": "Texas Instruments DC-DC Converters, WQFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "power management (pmic)",
    "lm26480sqx-aa",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "lm26480sqx-aa.kicad_sym",
    "lm26480sqx-aa.kicad_mod",
    "lm26480sqx-aa.glb",
    "lm26480sqx-aa.step",
    "lm26480sqx-aa.lbr",
    "docs/hero.png",
    "docs/lm26480sqx-aa-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "component": {
    "mpn": "LM26480SQX-AA",
    "manufacturer": "Texas Instruments",
    "package": "WQFN-24-EP(4x4)",
    "pin_count": 25,
    "category": "Power Management (PMIC)",
    "subcategory": "DC-DC Converters",
    "datasheet": "https://www.ti.com/cn/lit/gpn/lm26480",
    "parts": {
      "symbol": "lm26480sqx-aa.kicad_sym",
      "footprint": "lm26480sqx-aa.kicad_mod",
      "model_3d": "lm26480sqx-aa-etched.glb",
      "model_3d_plain": "lm26480sqx-aa.glb",
      "model_3d_step": "lm26480sqx-aa-etched.step",
      "model_3d_step_plain": "lm26480sqx-aa.step",
      "lbr": "lm26480sqx-aa.lbr"
    },
    "distributor_links": {
      "lcsc": "C2876374"
    },
    "pins": [
      {
        "number": "1",
        "name": "VINLDO12",
        "type": "power_in",
        "description": "Analog power supply for internal reference, bias, and logic circuits; requires 2.8V to 5.5V"
      },
      {
        "number": "2",
        "name": "SYNC",
        "type": "input",
        "description": "External oscillator synchronization input operating range 10.4 MHz to 15.6 MHz; must be grounded when not used"
      },
      {
        "number": "3",
        "name": "NPOR",
        "type": "tri_state",
        "description": "Open-drain power-on reset output for Buck1 and Buck2; pulled to ground when output voltages fall below specification with programmable delay of 60 ms default"
      },
      {
        "number": "4",
        "name": "GND_SW1",
        "type": "power_in",
        "description": "Buck1 NMOS switching power ground"
      },
      {
        "number": "5",
        "name": "SW1",
        "type": "power_out",
        "description": "Buck1 synchronous step-down converter output; programmable 0.8V to 2V with 1.5A maximum output current"
      },
      {
        "number": "6",
        "name": "VIN1",
        "type": "power_in",
        "description": "Buck1 power input from DC source or battery; accepts 2.8V to 5.5V"
      },
      {
        "number": "7",
        "name": "ENSW1",
        "type": "input",
        "description": "Buck1 enable input; logic HIGH enables converter operation; pin cannot be left floating"
      },
      {
        "number": "8",
        "name": "FB1",
        "type": "input",
        "description": "Buck1 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"
      },
      {
        "number": "9",
        "name": "GND_C",
        "type": "power_in",
        "description": "Non-switching core ground for analog and control circuits"
      },
      {
        "number": "10",
        "name": "AVDD",
        "type": "power_in",
        "description": "Analog power supply for Buck converter control circuits; requires 2.8V to 5.5V"
      },
      {
        "number": "11",
        "name": "FB2",
        "type": "input",
        "description": "Buck2 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"
      },
      {
        "number": "12",
        "name": "ENSW2",
        "type": "input",
        "description": "Buck2 enable input; logic HIGH enables converter operation; pin cannot be left floating"
      },
      {
        "number": "13",
        "name": "VIN2",
        "type": "power_in",
        "description": "Buck2 power input from DC source or battery; accepts 2.8V to 5.5V"
      },
      {
        "number": "14",
        "name": "SW2",
        "type": "power_out",
        "description": "Buck2 synchronous step-down converter output; programmable 1V to 3.3V with 1.5A maximum output current"
      },
      {
        "number": "15",
        "name": "GND_SW2",
        "type": "power_in",
        "description": "Buck2 NMOS switching power ground"
      },
      {
        "number": "16",
        "name": "ENLDO2",
        "type": "input",
        "description": "LDO2 enable input; logic HIGH enables regulator operation; pin cannot be left floating"
      },
      {
        "number": "17",
        "name": "ENLDO1",
        "type": "input",
        "description": "LDO1 enable input; logic HIGH enables regulator operation; pin cannot be left floating"
      },
      {
        "number": "18",
        "name": "GND_L",
        "type": "power_in",
        "description": "LDO linear regulator ground"
      },
      {
        "number": "19",
        "name": "VINLDO1",
        "type": "power_in",
        "description": "LDO1 power input from DC source or battery; requires minimum 1.74V when enabled, maximum 5.5V"
      },
      {
        "number": "20",
        "name": "LDO1",
        "type": "power_out",
        "description": "LDO1 regulated output; programmable 1V to 3.5V with 300mA maximum output current and 25mV typical dropout voltage"
      },
      {
        "number": "21",
        "name": "FBL1",
        "type": "input",
        "description": "LDO1 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"
      },
      {
        "number": "22",
        "name": "FBL2",
        "type": "input",
        "description": "LDO2 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"
      },
      {
        "number": "23",
        "name": "LDO2",
        "type": "power_out",
        "description": "LDO2 regulated output; programmable 1V to 3.5V with 300mA maximum output current and 25mV typical dropout voltage"
      },
      {
        "number": "24",
        "name": "VINLDO2",
        "type": "power_in",
        "description": "LDO2 power input from DC source or battery; requires minimum 1.74V when enabled, maximum 5.5V"
      },
      {
        "number": "25",
        "name": "DAP",
        "type": "power_in",
        "description": "Exposed thermal die attach pad for improved thermal dissipation; soldering to PCB recommended for thermal and mechanical performance"
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.2",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.2",
        "primary_model": "claude-haiku-4-5-20251001",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [],
        "pages_sent": 44,
        "cost_usd": 0.444,
        "at": "2026-09-23T19:01:27"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/lm26480",
        "pages": 44,
        "sha256": "9fa8e8bf5131003e",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 25,
        "described": 25,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "lm26480sqx-aa.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.0,
          4.0,
          0.77
        ],
        "zmin_mm": 0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "096fc110543e6d324c5120c2d38e3dca87a389da9b6fac234f1fe40856295ef4",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "lm26480sqx-aa-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.0,
          4.0,
          0.77
        ],
        "zmin_mm": 0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "ff6f73534a3def6938f999ca674258d7de511678597a9178f4cf87750d03c9d0",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}