← Commit history
README.md+68−8
@@ -2,16 +2,20 @@  **Texas Instruments** · DC-DC Converters · TO-263-7 -LM2586SX-ADJ from Texas Instruments, in a TO-263-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.+LM2586SX-ADJ from Texas Instruments, in a TO-263-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.  ## Pinout  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | ON/OFF (FREQ ADJ) | input | External shutdown / frequency-adjust pin (absolute max −0.4V ≤ VSH ≤ 6V); sourcing ≥3V into this pin (typical threshold 1.6V, min 1.0V/0.8V, max 2.2V/2.4V, typical pin current 40µA) shuts the device down; alternatively a resistor from this pin to ground sets the switching frequency from 100kHz (pin open) up to 200kHz (RSET=22kΩ); leave floating through an isolation diode for normal operation. |-| 4 | GND | power_in | Ground/return pin for the IC; a Schottky diode can be connected between the Switch pin (5) and this ground pin (4) to clamp negative ringing on the Switch node from dropping below −0.4V. |-| 5 | SWITCH | output | Collector of the internal 3A NPN power switch; absolute maximum −0.4V ≤ VSW ≤ 65V (recommended 0V ≤ VSW ≤ 60V); switch current is internally limited (typical 4.0A, min 3.0A, max 7.0A) with a typical saturation voltage of 0.45V at 3A; connects to the external inductor/transformer primary. |-| 6 | SYNC | input | Frequency-synchronization input, absolute maximum −0.4V ≤ VSYNC ≤ 2V; a negative-going pulse applied here (threshold typically 0.75V at 200kHz, pin current ~100µA typ/200µA max) synchronizes the internal oscillator to an external clock so multiple devices can run at the same switching frequency. |+| 1 | Freq. Adj., ON/OFF | input | Freq. Adj. - ON/OFF |+| 2 | Compensation | input | Compensation |+| 3 | Feedback | input | Feedback |+| 4 | Ground | power_in | Ground |+| 5 | Switch | passive | Collector of the internal 3A NPN power switch; absolute maximum −0.4V ≤ VSW ≤ 65V (recommended 0V ≤ VSW ≤ 60V); switch current is internally limited (typical 4.0A, min 3.0A, max 7.0A) with a typical saturation voltage of 0.45V at 3A; connects to the external inductor/transformer primary. |+| 6 | Freq. Sync. | input | Freq. Sync. |+| 7 | VIN | power_in | VIN |+| 8 | Ground | power_in | Package tab (pad 8). The DDPAK drawing does not label the tab; the 7-pin TO-220 drawing on the same page labels it GND, and pin 4 (centre lead) is Ground (task master ruling 2026-11-17). |  ## Key specifications @@ -20,7 +24,63 @@ LM2586SX-ADJ from Texas Instruments, in a TO-263-7. Pinout and pin descriptions | Manufacturer | Texas Instruments | | Package | TO-263-7 | | Category | Power Management (PMIC) |-| Pins | 4 |+| Pins | 8 |++## Electrical characteristics++Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).++| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |+|---|---|---|---|---|---|---|---|+| VOUT Output Voltage (adjustable) | VOUT | 11.52 | 12 | 12.48 | V | VIN = 4V to 10V; ILOAD = 0.2A to 0.8A | 8 |+| Line Regulation | ΔVOUT/ΔVIN |  | 20 | 100 | mV | VIN = 4V to 10V; ILOAD = 0.2A | 8 |+| Load Regulation | ΔVOUT/ΔILOAD |  | 20 | 100 | mV | VIN = 10V; ILOAD = 0.2A to 0.8A | 8 |+| Output Reference Voltage | VREF | 1.208 | 1.23 | 1.252 | V | Measured at Feedback Pin; VCOMP = 1.0V | 8 |+| Error Amp Transconductance | GM | 1.8 | 3.2 | 6 | mmho | ICOMP = −30 μA to +30 μA; VCOMP = 1.0V | 8 |+| Error Amp Voltage Gain | AVOL | 400 | 670 |  | V/V | VCOMP = 0.5V to 1.6V; RCOMP = 1.0 MΩ (note 3) | 8 |+| Error Amp Input Bias Current | IB |  | 125 | 425 | nA | VCOMP = 1.0V | 8 |+| Input Supply Current, Switch Off | IS |  | 11 | 15.5 | mA | Switch Off (note 4) | 8 |+| Input Supply Current |  |  | 50 | 100 | mA | ISWITCH = 1.8A | 8 |+| Shutdown Input Supply Current | IS/D |  | 16 | 100 | μA | VSH = 3V | 8 |+| Input Supply Undervoltage Lockout | VUV | 3.05 | 3.3 | 3.75 | V | RLOAD = 100Ω | 8 |+| Oscillator Frequency | fO | 85 | 100 | 115 | kHz | Measured at Switch Pin; RLOAD = 100Ω; VCOMP = 1.0V; Freq. Adj. Pin open (Pin 1) | 8 |+| Error Amplifier Output Swing, Upper Limit | VEAO | 2.6 | 2.8 |  | V | Upper Limit (note 5) | 8 |+| Error Amplifier Output Swing, Lower Limit | VEAO |  | 0.25 | 0.4 | V | Lower Limit (note 4) | 8 |+| Error Amp Output Current (Source or Sink) | IEAO | 110 | 165 | 260 | μA | See note (6) | 8 |+| Soft Start Current | ISS | 8 | 11 | 17 | μA | VFEEDBACK = 0.92V; VCOMP = 1.0V | 8 |+| Maximum Duty Cycle | DMAX | 93 | 98 |  | % | RLOAD = 100Ω (note 5) | 8 |+| Switch Leakage Current, Switch Off | IL |  | 15 | 300 | μA | Switch off; VSWITCH = 60V | 8 |+| Switch Saturation Voltage | VSAT |  | 0.45 | 0.65 | V | ISWITCH = 3.0A | 8 |+| NPN Switch Current Limit | ICL | 3 | 4 | 7 | A |  | 9 |+| Synchronization Threshold Voltage | VSTH | 0.625 | 0.75 | 0.875 | V | FSYNC = 200 kHz; VCOMP = 1V; VIN = 5V | 9 |+| Synchronization Pin Current | ISYNC |  | 100 | 200 | μA | VIN = 5V; VCOMP = 1V; VSYNC = VSTH | 9 |+| ON/OFF Pin Threshold Voltage | VSHTH | 1 | 1.6 | 2.2 | V | VCOMP = 1V (note 7) | 9 |+| ON/OFF Pin Current | ISH | 15 | 40 | 65 | μA | VCOMP = 1V; VSH = VSHTH | 9 |+| Input Voltage (absolute maximum) | VIN | -0.4 |  | 45 | V |  | 4 |+| Switch Voltage (absolute maximum) | VSW | -0.4 |  | 65 | V |  | 4 |+| Compensation Pin Voltage (absolute maximum) | VCOMP | -0.4 |  | 2.4 | V |  | 4 |+| Feedback Pin Voltage (absolute maximum) | VFB | -0.4 |  |  | V | Upper limit printed as 2 VOUT (expression, not numeric) | 4 |+| ON/OFF Pin Voltage (absolute maximum) | VSH | -0.4 |  | 6 | V |  | 4 |+| Sync Pin Voltage (absolute maximum) | VSYNC | -0.4 |  | 2 | V |  | 4 |+| Storage Temperature Range |  | -65 |  | 150 | °C |  | 4 |+| Lead Temperature |  |  |  | 260 | °C | Soldering, 10 sec. | 4 |+| Maximum Junction Temperature |  |  |  | 150 | °C |  | 4 |+| Supply Voltage (recommended) | VIN | 4 |  | 40 | V |  | 4 |+| Output Switch Voltage (recommended) | VSW | 0 |  | 60 | V |  | 4 |+| Output Switch Current (recommended) | ISW |  |  | 3 | A |  | 4 |+| Junction Temperature Range (recommended) | TJ | -40 |  | 125 | °C |  | 4 |+| Junction-to-ambient thermal resistance, KTW (TO-263) | RθJA |  | 56 |  | °C/W | Mounted horizontally, 0.136 in² of 1 oz copper (note 2) | 5 |+| Junction-to-ambient thermal resistance, KTW (TO-263) | RθJA |  | 35 |  | °C/W | Mounted horizontally, 0.4896 in² of 1 oz copper (note 4) | 5 |+| Junction-to-ambient thermal resistance, KTW (TO-263) | RθJA |  | 26 |  | °C/W | Mounted horizontally, 1.0064 in² of 1 oz copper (note 6) | 5 |+| Junction-to-case thermal resistance, KTW (TO-263) | RθJC |  | 2 |  | °C/W |  | 5 |++## Materials and finish++As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).++| Part | Material | Colour / plating | Datasheet says | Page |+|---|---|---|---|---|+| contacts | copper |  | (3) Junction-to-ambient thermal resistance (no external heat sink) for the 7-lead TO-220 package mounted vertically, with ½ inch leads in a socket, or on a PC board with minimum copper area. | 5 |  ## CAD (KiCad official) @@ -33,9 +93,9 @@ LM2586SX-ADJ from Texas Instruments, in a TO-263-7. Pinout and pin descriptions  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm2586) (44 pp, sha256 `062506d4c1c2d784`, retrieved 2026-09-24, tier: lcsc)+- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm2586) (44 pp, sha256 `062506d4c1c2d784`, retrieved 2026-11-17, tier: manufacturer) - **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.-- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).  [Datasheet PDF](docs/lm2586sx-adj-datasheet.pdf)
lm2586sx-adj-hero.glbadded
⋯ 1 unchanged line ⋯
lm2586sx-adj-hero.overlay.jsonadded+265
@@ -0,0 +1,265 @@+{+ "spec": "adom-hero 1.4",+ "mpn": "LM2586SX-ADJ",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+  "pad_outlines": {+   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+   "rgba": [+    0.0,+    0.902,+    0.863,+    0.5+   ],+   "pads": 8,+   "span_mm": 18.55,+   "dash_mm": 0.45,+   "gap_mm": 0.27,+   "pad_stroke_mm": 0.09+  },+  "silkscreen": {+   "material": "Silkscreen reference lines - 30 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.3+   ],+   "footprint_items": 5,+   "pin1": {+    "source": "footprint silkscreen",+    "pad": "1"+   }+  },+  "signal_names": {+   "material": "Signal names - 50 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.5+   ],+   "font": "DejaVu Sans Mono",+   "labels": 8,+   "sides": "top + mirrored underside (single-sided)",+   "omitted": null,+   "fallback_to_pad_number": 0+  }+ },+ "align": {+  "ok": true,+  "board_underside": true,+  "electrical_pads_without_contact": [],+  "mounting_pads_left_out": [],+  "centre_offset_mm": 0.0,+  "over_pads": false,+  "tolerance_mm": 1.292,+  "orientation_flipped": false,+  "contacts_bbox_mm": [+   -9.375,+   5.625,+   -5.0,+   5.0+  ],+  "pads_bbox_mm": [+   -9.95,+   6.2,+   -5.4,+   5.4+  ],+  "seating_z_mm": 0.0+ },+ "sources": {+  "glb": "lm2586sx-adj-etched.glb",+  "glb_sha256": "99921fb017bf552870b9460a494a6cde48776cd806b4b3aa6dd3e0502c01a330",+  "footprint": "lm2586sx-adj.kicad_mod",+  "footprint_sha256": "777bb53188f3029e91dce5500a7734ac73b51c4b6626097d3e53fba39588731f",+  "pins": "page.json component.pins",+  "pins_sha256": "9a9a3fb1c3852c876ea0e33f998e86855885b444ed97864f0d7c3d7f2eb0bf06"+ },+ "generator": "factory/hero_glb.py",+ "labels": [+  {+   "pad": "1",+   "text": "Freq. Adj. \u2013 ON/OFF",+   "x": -10.1,+   "y": -3.81,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "2",+   "text": "Compensation",+   "x": -10.1,+   "y": -2.54,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "3",+   "text": "Feedback",+   "x": -10.1,+   "y": -1.27,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "4",+   "text": "Ground",+   "x": -10.1,+   "y": 0.0,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "5",+   "text": "Switch",+   "x": -10.1,+   "y": 1.27,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "6",+   "text": "Freq. Sync.",+   "x": -10.1,+   "y": 2.54,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "7",+   "text": "VIN",+   "x": -10.1,+   "y": 3.81,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "8",+   "text": "Ground",+   "x": 6.35,+   "y": 0.0,+   "align": "left",+   "vertical": false,+   "h": 0.6+  }+ ],+ "pads": [+  {+   "number": "1",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    -3.81+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    -2.54+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "3",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    -1.27+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "4",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    0.0+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "5",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    1.27+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "6",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    2.54+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "7",+   "shape": "roundrect",+   "center_mm": [+    -7.65,+    3.81+   ],+   "size_mm": [+    4.6,+    0.8+   ],+   "rot": 0.0+  },+  {+   "number": "8",+   "shape": "roundrect",+   "center_mm": [+    1.5,+    0.0+   ],+   "size_mm": [+    9.4,+    10.8+   ],+   "rot": 0.0+  }+ ]+}\ No newline at end of file
lm2586sx-adj.kicad_sym+27−11
@@ -1,27 +1,43 @@ (kicad_symbol_lib (version 20211014) (generator ds2sf_rect)   (symbol "LM2586SX-ADJ" (in_bom yes) (on_board yes)-    (property "Reference" "U" (at 0 5.08 0) (effects (font (size 1.27 1.27))))-    (property "Value" "LM2586SX-ADJ" (at 0 -7.62 0) (effects (font (size 1.27 1.27))))+    (property "Reference" "U" (at 0 7.62 0) (effects (font (size 1.27 1.27))))+    (property "Value" "LM2586SX-ADJ" (at 0 -10.16 0) (effects (font (size 1.27 1.27))))     (property "Footprint" "" (at 0 0 0) (effects (font (size 1.27 1.27)) hide))     (symbol "LM2586SX-ADJ_0_1"-    (rectangle (start -12.70 2.54) (end 12.70 -5.08)+    (rectangle (start -15.24 5.08) (end 15.24 -7.62)       (stroke (width 0.254) (type default)) (fill (type background)))     )     (symbol "LM2586SX-ADJ_1_1"-    (pin input line (at -17.78 0.00 0) (length 5.08)-      (name "ON/OFF (FREQ ADJ)" (effects (font (size 1.27 1.27))))+    (pin input line (at -20.32 2.54 0) (length 5.08)+      (name "Freq. Adj. – ON/OFF" (effects (font (size 1.27 1.27))))       (number "1" (effects (font (size 1.27 1.27))))     )-    (pin power_in line (at -17.78 -2.54 0) (length 5.08)-      (name "GND" (effects (font (size 1.27 1.27))))+    (pin input line (at -20.32 0.00 0) (length 5.08)+      (name "Compensation" (effects (font (size 1.27 1.27))))+      (number "2" (effects (font (size 1.27 1.27))))+    )+    (pin input line (at -20.32 -2.54 0) (length 5.08)+      (name "Feedback" (effects (font (size 1.27 1.27))))+      (number "3" (effects (font (size 1.27 1.27))))+    )+    (pin power_in line (at -20.32 -5.08 0) (length 5.08)+      (name "Ground" (effects (font (size 1.27 1.27))))       (number "4" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 17.78 0.00 180) (length 5.08)-      (name "SYNC" (effects (font (size 1.27 1.27))))+    (pin power_in line (at 20.32 2.54 180) (length 5.08)+      (name "Ground" (effects (font (size 1.27 1.27))))+      (number "8" (effects (font (size 1.27 1.27))))+    )+    (pin power_in line (at 20.32 0.00 180) (length 5.08)+      (name "VIN" (effects (font (size 1.27 1.27))))+      (number "7" (effects (font (size 1.27 1.27))))+    )+    (pin input line (at 20.32 -2.54 180) (length 5.08)+      (name "Freq. Sync." (effects (font (size 1.27 1.27))))       (number "6" (effects (font (size 1.27 1.27))))     )-    (pin output line (at 17.78 -2.54 180) (length 5.08)-      (name "SWITCH" (effects (font (size 1.27 1.27))))+    (pin passive line (at 20.32 -5.08 180) (length 5.08)+      (name "Switch" (effects (font (size 1.27 1.27))))       (number "5" (effects (font (size 1.27 1.27))))     )     )
lm2586sx-adj.lbr+35−18
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>Texas Instruments DC-DC Converters, TO-263-7. Pinout cross-checked by two models against the datasheet</description> <packages> <package name="TO-263-7_TabPin8">   <description>8 pads, 16.1 x 10.8 mm. TO-263/D2PAK/DDPAK SMD package</description>@@ -61,7 +61,7 @@   <smd name="5" x="-7.6500" y="-1.2700" dx="4.6000" dy="0.8000" layer="1" roundness="50"/>   <smd name="6" x="-7.6500" y="-2.5400" dx="4.6000" dy="0.8000" layer="1" roundness="50"/>   <smd name="7" x="-7.6500" y="-3.8100" dx="4.6000" dy="0.8000" layer="1" roundness="50"/>-  <smd name="8" x="1.5000" y="-0.0000" dx="9.4000" dy="10.8000" layer="1" roundness="5"/>+  <smd name="8" x="1.5000" y="-0.0000" dx="9.4000" dy="10.8000" layer="1" roundness="5" cream="no"/>   <polygon width="0.1200" layer="21">     <vertex x="-7.6500" y="4.4700"/>     <vertex x="-7.9900" y="4.9400"/>@@ -108,33 +108,50 @@ </packages> <symbols> <symbol name="LM2586SX-ADJ">-  <wire x1="-12.7" y1="2.54" x2="12.7" y2="2.54" width="0.254" layer="94"/>-  <wire x1="12.7" y1="2.54" x2="12.7" y2="-5.08" width="0.254" layer="94"/>-  <wire x1="12.7" y1="-5.08" x2="-12.7" y2="-5.08" width="0.254" layer="94"/>-  <wire x1="-12.7" y1="-5.08" x2="-12.7" y2="2.54" width="0.254" layer="94"/>-  <text x="0.0000" y="5.0800" size="1.27" layer="95" align="center">&gt;NAME</text>-  <text x="0.0000" y="-7.6200" size="1.27" layer="96" align="center">&gt;VALUE</text>-  <pin name="ON/OFF_FREQ_ADJ" x="-17.78" y="0" length="middle" direction="in"/>-  <pin name="GND" x="-17.78" y="-2.54" length="middle" direction="pwr"/>-  <pin name="SYNC" x="17.78" y="0" length="middle" direction="in" rot="R180"/>-  <pin name="SWITCH" x="17.78" y="-2.54" length="middle" direction="out" rot="R180"/>+  <description>Texas Instruments DC-DC Converters, TO-263-7. Pinout cross-checked by two models against the datasheet</description>+  <wire x1="-15.24" y1="5.08" x2="15.24" y2="5.08" width="0.254" layer="94"/>+  <wire x1="15.24" y1="5.08" x2="15.24" y2="-7.62" width="0.254" layer="94"/>+  <wire x1="15.24" y1="-7.62" x2="-15.24" y2="-7.62" width="0.254" layer="94"/>+  <wire x1="-15.24" y1="-7.62" x2="-15.24" y2="5.08" width="0.254" layer="94"/>+  <text x="0.0000" y="7.6200" size="1.27" layer="95" align="center">&gt;NAME</text>+  <text x="0.0000" y="-10.1600" size="1.27" layer="96" align="center">&gt;VALUE</text>+  <pin name="Freq._Adj._ON/OFF" x="-20.32" y="2.54" length="middle" direction="in"/>+  <pin name="Compensation" x="-20.32" y="0" length="middle" direction="in"/>+  <pin name="Feedback" x="-20.32" y="-2.54" length="middle" direction="in"/>+  <pin name="Ground" x="-20.32" y="-5.08" length="middle" direction="pwr"/>+  <pin name="Ground@2" x="20.32" y="2.54" length="middle" direction="pwr" rot="R180"/>+  <pin name="VIN" x="20.32" y="0" length="middle" direction="pwr" rot="R180"/>+  <pin name="Freq._Sync." x="20.32" y="-2.54" length="middle" direction="in" rot="R180"/>+  <pin name="Switch" x="20.32" y="-5.08" length="middle" direction="pas" rot="R180"/> </symbol> </symbols> <devicesets> <deviceset name="LM2586SX-ADJ" prefix="U">-  <description></description>+  <description>Texas Instruments DC-DC Converters, TO-263-7. Pinout cross-checked by two models against the datasheet</description>   <gates>     <gate name="G$1" symbol="LM2586SX-ADJ" x="0" y="0"/>   </gates>   <devices>     <device name="" package="TO-263-7_TabPin8">       <connects>-        <connect gate="G$1" pin="ON/OFF_FREQ_ADJ" pad="1"/>-        <connect gate="G$1" pin="GND" pad="4"/>-        <connect gate="G$1" pin="SYNC" pad="6"/>-        <connect gate="G$1" pin="SWITCH" pad="5"/>+        <connect gate="G$1" pin="Freq._Adj._ON/OFF" pad="1"/>+        <connect gate="G$1" pin="Compensation" pad="2"/>+        <connect gate="G$1" pin="Feedback" pad="3"/>+        <connect gate="G$1" pin="Ground" pad="4"/>+        <connect gate="G$1" pin="Ground@2" pad="8"/>+        <connect gate="G$1" pin="VIN" pad="7"/>+        <connect gate="G$1" pin="Freq._Sync." pad="6"/>+        <connect gate="G$1" pin="Switch" pad="5"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="LM2586SX-ADJ" constant="no"/>+          <attribute name="MANUFACTURER" value="Texas Instruments" constant="no"/>+          <attribute name="DATASHEET" value="https://www.ti.com/cn/lit/gpn/lm2586" constant="no"/>+          <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/lm2586sx-adj" constant="no"/>+          <attribute name="LCSC_PN" value="C181324" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
package.json+60−38
@@ -1,8 +1,8 @@ {   "slug": "lm2586sx-adj",-  "version": "0.1.0",+  "version": "0.2.0",   "type": "component",-  "description": "Texas Instruments DC-DC Converters, TO-263-7. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "description": "Texas Instruments DC-DC Converters, TO-263-7. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",   "tags": [     "component",     "power management (pmic)",@@ -26,83 +26,105 @@     "docs/hero.png",     "docs/lm2586sx-adj-datasheet.pdf",     "viewers/symbol.html",-    "viewers/footprint.html"+    "viewers/footprint.html",+    "lm2586sx-adj-hero.glb",+    "lm2586sx-adj-hero.overlay.json"   ],   "component": {     "mpn": "LM2586SX-ADJ",     "manufacturer": "Texas Instruments",     "package": "TO-263-7",-    "pin_count": 4,+    "pin_count": 8,     "category": "Power Management (PMIC)",     "subcategory": "DC-DC Converters",     "datasheet": "https://www.ti.com/cn/lit/gpn/lm2586",     "parts": {       "symbol": "lm2586sx-adj.kicad_sym",       "footprint": "lm2586sx-adj.kicad_mod",-      "model_3d": "lm2586sx-adj-etched.glb",+      "model_3d": "lm2586sx-adj-hero.glb",       "model_3d_plain": "lm2586sx-adj.glb",       "model_3d_step": "lm2586sx-adj-etched.step",       "model_3d_step_plain": "lm2586sx-adj.step",       "lbr": "lm2586sx-adj.lbr"     },     "distributor_links": {-      "lcsc": "C181324"+      "lcsc": "C181324",+      "digikey": "LM2586SX-ADJ/NOPBTR-ND"+    },+    "distributor_check": {+      "checked_at": "2026-11-17T06:45:12Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "LM2586SX-ADJ/NOPBTR-ND",+        "status": "found"+      },+      "mouser": {+        "pn": null,+        "status": "quota"+      }     },     "pins": [       {         "number": "1",-        "name": "ON/OFF (FREQ ADJ)",+        "name": "Freq. Adj. – ON/OFF",+        "type": "input",+        "description": "Freq. Adj. - ON/OFF"+      },+      {+        "number": "2",+        "name": "Compensation",+        "type": "input",+        "description": "Compensation"+      },+      {+        "number": "3",+        "name": "Feedback",         "type": "input",-        "description": "External shutdown / frequency-adjust pin (absolute max −0.4V ≤ VSH ≤ 6V); sourcing ≥3V into this pin (typical threshold 1.6V, min 1.0V/0.8V, max 2.2V/2.4V, typical pin current 40µA) shuts the device down; alternatively a resistor from this pin to ground sets the switching frequency from 100kHz (pin open) up to 200kHz (RSET=22kΩ); leave floating through an isolation diode for normal operation."+        "description": "Feedback"       },       {         "number": "4",-        "name": "GND",+        "name": "Ground",         "type": "power_in",-        "description": "Ground/return pin for the IC; a Schottky diode can be connected between the Switch pin (5) and this ground pin (4) to clamp negative ringing on the Switch node from dropping below −0.4V."+        "description": "Ground"       },       {         "number": "5",-        "name": "SWITCH",-        "type": "output",+        "name": "Switch",+        "type": "passive",         "description": "Collector of the internal 3A NPN power switch; absolute maximum −0.4V ≤ VSW ≤ 65V (recommended 0V ≤ VSW ≤ 60V); switch current is internally limited (typical 4.0A, min 3.0A, max 7.0A) with a typical saturation voltage of 0.45V at 3A; connects to the external inductor/transformer primary."       },       {         "number": "6",-        "name": "SYNC",+        "name": "Freq. Sync.",         "type": "input",-        "description": "Frequency-synchronization input, absolute maximum −0.4V ≤ VSYNC ≤ 2V; a negative-going pulse applied here (threshold typically 0.75V at 200kHz, pin current ~100µA typ/200µA max) synchronizes the internal oscillator to an external clock so multiple devices can run at the same switching frequency."+        "description": "Freq. Sync."+      },+      {+        "number": "7",+        "name": "VIN",+        "type": "power_in",+        "description": "VIN"+      },+      {+        "number": "8",+        "name": "Ground",+        "type": "power_in",+        "description": "Package tab (pad 8). The DDPAK drawing does not label the tab; the 7-pin TO-220 drawing on the same page labels it GND, and pin 4 (centre lead) is Ground (task master ruling 2026-11-17)."       }     ],     "provenance": {-      "extractor": "extract_pins 0.2",-      "factory_chain": {-        "factory": "2.0.0",-        "extractor": "extract_pins 0.2",-        "primary_model": "claude-haiku-4-5-20251001",-        "primary_mode": "text",-        "consensus_model": "claude-sonnet-5",-        "consensus": "agreed",-        "guards": "pin_guards 0.1: passed",-        "guard_notes": [-          "extractor flagged: TO-263-7 package pinout diagram on page 3 not fully captured in text extraction; pin numbering confi; Pin 1 has dual-function capability: operation as ON/OFF shutdown control with voltage threshold (1.0",-          "exposed pad 8 added from the footprint",-          "1/8 pin names appear NOWHERE in the datasheet text: ['4:GND@p3']"-        ],-        "pages_sent": 44,-        "cost_usd": 0.4643,-        "at": "2026-09-24T10:59:53"-      },+      "extractor": "ds2sf",       "datasheet": {         "url": "https://www.ti.com/cn/lit/gpn/lm2586",         "pages": 44,         "sha256": "062506d4c1c2d784",-        "source_tier": "lcsc"+        "source_tier": "mfr"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 8,+        "described": 8,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -128,7 +150,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "34b8121b216e7b6490402befe573a69b06919acafd33d6e8da88bd238574da52",-        "checked": "2026-10-07",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -146,8 +168,8 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "fc850eb068f65bdfc38a41ca9218d1f8c8d9d9a59f6097ae09ad8c02b8b30f77",-        "checked": "2026-10-16",+        "sha256": "0f606f73900fd63c908effe9be86c78c26b93985aa29c98209b31e1c99d83f1d",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]
page.json+71−49
@@ -4,7 +4,7 @@   "slug": "lm2586sx-adj",   "title": "LM2586SX-ADJ",   "brief": "Texas Instruments DC-DC Converters, TO-263-7. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.2.0",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -17,77 +17,97 @@     "mpn": "LM2586SX-ADJ",     "manufacturer": "Texas Instruments",     "package": "TO-263-7",-    "pin_count": 4,+    "pin_count": 8,     "category": "Power Management (PMIC)",     "subcategory": "DC-DC Converters",     "datasheet": "https://www.ti.com/cn/lit/gpn/lm2586",     "parts": {       "symbol": "lm2586sx-adj.kicad_sym",       "footprint": "lm2586sx-adj.kicad_mod",-      "model_3d": "lm2586sx-adj-etched.glb",+      "model_3d": "lm2586sx-adj-hero.glb",       "model_3d_plain": "lm2586sx-adj.glb",       "model_3d_step": "lm2586sx-adj-etched.step",       "model_3d_step_plain": "lm2586sx-adj.step",       "lbr": "lm2586sx-adj.lbr"     },     "distributor_links": {-      "lcsc": "C181324"+      "lcsc": "C181324",+      "digikey": "LM2586SX-ADJ/NOPBTR-ND"+    },+    "distributor_check": {+      "checked_at": "2026-11-17T06:45:12Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "LM2586SX-ADJ/NOPBTR-ND",+        "status": "found"+      },+      "mouser": {+        "pn": null,+        "status": "quota"+      }     },     "pins": [       {         "number": "1",-        "name": "ON/OFF (FREQ ADJ)",+        "name": "Freq. Adj. – ON/OFF",+        "type": "input",+        "description": "Freq. Adj. - ON/OFF"+      },+      {+        "number": "2",+        "name": "Compensation",+        "type": "input",+        "description": "Compensation"+      },+      {+        "number": "3",+        "name": "Feedback",         "type": "input",-        "description": "External shutdown / frequency-adjust pin (absolute max −0.4V ≤ VSH ≤ 6V); sourcing ≥3V into this pin (typical threshold 1.6V, min 1.0V/0.8V, max 2.2V/2.4V, typical pin current 40µA) shuts the device down; alternatively a resistor from this pin to ground sets the switching frequency from 100kHz (pin open) up to 200kHz (RSET=22kΩ); leave floating through an isolation diode for normal operation."+        "description": "Feedback"       },       {         "number": "4",-        "name": "GND",+        "name": "Ground",         "type": "power_in",-        "description": "Ground/return pin for the IC; a Schottky diode can be connected between the Switch pin (5) and this ground pin (4) to clamp negative ringing on the Switch node from dropping below −0.4V."+        "description": "Ground"       },       {         "number": "5",-        "name": "SWITCH",-        "type": "output",+        "name": "Switch",+        "type": "passive",         "description": "Collector of the internal 3A NPN power switch; absolute maximum −0.4V ≤ VSW ≤ 65V (recommended 0V ≤ VSW ≤ 60V); switch current is internally limited (typical 4.0A, min 3.0A, max 7.0A) with a typical saturation voltage of 0.45V at 3A; connects to the external inductor/transformer primary."       },       {         "number": "6",-        "name": "SYNC",+        "name": "Freq. Sync.",         "type": "input",-        "description": "Frequency-synchronization input, absolute maximum −0.4V ≤ VSYNC ≤ 2V; a negative-going pulse applied here (threshold typically 0.75V at 200kHz, pin current ~100µA typ/200µA max) synchronizes the internal oscillator to an external clock so multiple devices can run at the same switching frequency."+        "description": "Freq. Sync."+      },+      {+        "number": "7",+        "name": "VIN",+        "type": "power_in",+        "description": "VIN"+      },+      {+        "number": "8",+        "name": "Ground",+        "type": "power_in",+        "description": "Package tab (pad 8). The DDPAK drawing does not label the tab; the 7-pin TO-220 drawing on the same page labels it GND, and pin 4 (centre lead) is Ground (task master ruling 2026-11-17)."       }     ],     "provenance": {-      "extractor": "extract_pins 0.2",-      "factory_chain": {-        "factory": "2.0.0",-        "extractor": "extract_pins 0.2",-        "primary_model": "claude-haiku-4-5-20251001",-        "primary_mode": "text",-        "consensus_model": "claude-sonnet-5",-        "consensus": "agreed",-        "guards": "pin_guards 0.1: passed",-        "guard_notes": [-          "extractor flagged: TO-263-7 package pinout diagram on page 3 not fully captured in text extraction; pin numbering confi; Pin 1 has dual-function capability: operation as ON/OFF shutdown control with voltage threshold (1.0",-          "exposed pad 8 added from the footprint",-          "1/8 pin names appear NOWHERE in the datasheet text: ['4:GND@p3']"-        ],-        "pages_sent": 44,-        "cost_usd": 0.4643,-        "at": "2026-09-24T10:59:53"-      },+      "extractor": "ds2sf",       "datasheet": {         "url": "https://www.ti.com/cn/lit/gpn/lm2586",         "pages": 44,         "sha256": "062506d4c1c2d784",-        "source_tier": "lcsc"+        "source_tier": "mfr"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 8,+        "described": 8,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -105,15 +125,15 @@         "origin": "footprint origin = pad-pattern centre",         "seat": "z = 0",         "extents_mm": [-          15.0,-          10.0,+          15,+          10,           4.42         ],-        "zmin_mm": 0.0,-        "centre_offset_mm": 0.0,+        "zmin_mm": 0,+        "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "34b8121b216e7b6490402befe573a69b06919acafd33d6e8da88bd238574da52",-        "checked": "2026-10-07",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -124,15 +144,15 @@         "origin": "footprint origin = pad-pattern centre",         "seat": "z = 0",         "extents_mm": [-          15.0,-          10.0,+          15,+          10,           4.42         ],-        "zmin_mm": 0.0,-        "centre_offset_mm": 0.0,+        "zmin_mm": 0,+        "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "fc850eb068f65bdfc38a41ca9218d1f8c8d9d9a59f6097ae09ad8c02b8b30f77",-        "checked": "2026-10-16",+        "sha256": "0f606f73900fd63c908effe9be86c78c26b93985aa29c98209b31e1c99d83f1d",+        "checked": "2026-11-17",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]@@ -177,9 +197,11 @@     "docs/hero.png",     "docs/lm2586sx-adj-datasheet.pdf",     "viewers/symbol.html",-    "viewers/footprint.html"+    "viewers/footprint.html",+    "lm2586sx-adj-hero.glb",+    "lm2586sx-adj-hero.overlay.json"   ],-  "visibility": {-    "public": true-  }-}+  "visibility": "public",+  "description": "Texas Instruments DC-DC Converters, TO-263-7. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",+  "org": "adom"+}\ No newline at end of file