← Commit history

lm25141qrgerq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)

Ray ·213d90fec6 · ·parent f83492f
2 files changed +94−14
package.json+52−12
@@ -59,7 +59,7 @@         "number": "2",         "name": "VDDA",         "type": "power_out",-        "description": "Internal analog bias regulator output (typ. 5 V, UVLO 3.2 V); requires ceramic bypass capacitor (\u2265100 nF) from VDDA to AGND."+        "description": "Internal analog bias regulator output (typ. 5 V, UVLO 3.2 V); requires ceramic bypass capacitor (≥100 nF) from VDDA to AGND."       },       {         "number": "3",@@ -77,7 +77,7 @@         "number": "5",         "name": "DITH",         "type": "output",-        "description": "Dither/frequency modulation output; capacitor to AGND charged/discharged by internal 20-\u00b5A source creates triangular waveform (1.14-1.26 V) modulating oscillator \u00b15%; disabled by connecting to VDDA."+        "description": "Dither/frequency modulation output; capacitor to AGND charged/discharged by internal 20-µA source creates triangular waveform (1.14-1.26 V) modulating oscillator ±5%; disabled by connecting to VDDA."       },       {         "number": "6",@@ -107,13 +107,13 @@         "number": "10",         "name": "VCC",         "type": "power_out",-        "description": "VCC bias supply output (nom. 5 V, range 4.75-5.25 V, UVLO 3.4 V); requires 2.2-4.7 \u00b5F bypass capacitor to PGND with 75 mA source current limit."+        "description": "VCC bias supply output (nom. 5 V, range 4.75-5.25 V, UVLO 3.4 V); requires 2.2-4.7 µF bypass capacitor to PGND with 75 mA source current limit."       },       {         "number": "11",         "name": "HB",         "type": "power_out",-        "description": "High-side bootstrap supply pin (0-5.25 V from SW); external bootstrap capacitor (0.1-0.47 \u00b5F ceramic, low-ESR) charged through bootstrap diode from VCC when SW low; UVLO threshold 2.5 V."+        "description": "High-side bootstrap supply pin (0-5.25 V from SW); external bootstrap capacitor (0.1-0.47 µF ceramic, low-ESR) charged through bootstrap diode from VCC when SW low; UVLO threshold 2.5 V."       },       {         "number": "12",@@ -155,7 +155,7 @@         "number": "18",         "name": "CS",         "type": "input",-        "description": "Current sense amplifier inverting input; make low-current Kelvin connection to inductor side of external current sense resistor; 75 mV threshold (\u00b10.9%) for cycle-by-cycle current limit with 12 V/V gain."+        "description": "Current sense amplifier inverting input; make low-current Kelvin connection to inductor side of external current sense resistor; 75 mV threshold (±0.9%) for cycle-by-cycle current limit with 12 V/V gain."       },       {         "number": "19",@@ -167,31 +167,31 @@         "number": "20",         "name": "COMP",         "type": "input",-        "description": "Compensation amplifier output pin for external error amplifier feedback network; transconductance amplifier input with 1200 \u00b5S typical gain and 1 V full-scale input range."+        "description": "Compensation amplifier output pin for external error amplifier feedback network; transconductance amplifier input with 1200 µS typical gain and 1 V full-scale input range."       },       {         "number": "21",         "name": "PG",         "type": "output",-        "description": "Power good open-collector output; switches low (<0.4 V at 2 mA sink) when VOUT falls below 92% or rises above 110% of regulation voltage with 25-\u00b5s overvoltage and 30-\u00b5s undervoltage filter delays."+        "description": "Power good open-collector output; switches low (<0.4 V at 2 mA sink) when VOUT falls below 92% or rises above 110% of regulation voltage with 25-µs overvoltage and 30-µs undervoltage filter delays."       },       {         "number": "22",         "name": "SS",         "type": "input",-        "description": "Soft-start programming pin; external capacitor and internal 20-\u00b5A current source control error amplifier ramp rate during startup; pulling below 80 mV disables gate driver outputs while maintaining other functions."+        "description": "Soft-start programming pin; external capacitor and internal 20-µA current source control error amplifier ramp rate during startup; pulling below 80 mV disables gate driver outputs while maintaining other functions."       },       {         "number": "23",         "name": "EN",         "type": "input",-        "description": "Active-high logic enable input (0-47 V range); controller enabled when >2 V, shutdown mode (<10 \u00b5A IQ) when <0.8 V; logic input leakage <1 \u00b5A."+        "description": "Active-high logic enable input (0-47 V range); controller enabled when >2 V, shutdown mode (<10 µA IQ) when <0.8 V; logic input leakage <1 µA."       },       {         "number": "24",         "name": "RES",         "type": "output",-        "description": "Hiccup restart timer pin; external capacitor (20-\u00b5A source current, 1.2 V threshold, 4 \u03a9 pulldown) sets recovery delay after 512 consecutive current-limit cycles; grounding to VDD during power-up disables hiccup protection."+        "description": "Hiccup restart timer pin; external capacitor (20-µA source current, 1.2 V threshold, 4 Ω pulldown) sets recovery delay after 512 consecutive current-limit cycles; grounding to VDD during power-up disables hiccup protection."       },       {         "number": "25",@@ -235,6 +235,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "lm25141qrgerq1.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "096fc110543e6d324c5120c2d38e3dca87a389da9b6fac234f1fe40856295ef4",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "lm25141qrgerq1-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "983c5551843f31f1e58c339a434f1a81055420bb4aee2cbb56e6d7d7154c8dca",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}
page.json+42−2
@@ -220,7 +220,47 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "lm25141qrgerq1.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "096fc110543e6d324c5120c2d38e3dca87a389da9b6fac234f1fe40856295ef4",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "lm25141qrgerq1-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          4.0,+          4.0,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "983c5551843f31f1e58c339a434f1a81055420bb4aee2cbb56e6d7d7154c8dca",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   },   "metadata": {     "specs": {@@ -268,4 +308,4 @@     "public": true   },   "updated_at": "2026-09-25T00:08:25.225Z"-}\ No newline at end of file+}