main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs lm25118mhe: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers lm25118mhe: viewers · Ray
lm25118mhe-etched.fit.json lm25118mhe: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
lm25118mhe-etched.glb lm25118mhe: etched from the flattened plain STEP (service-occt 1.6.0, from the plain STEP) · Ray
lm25118mhe-etched.step lm25118mhe: etched from the flattened plain STEP (service-occt 1.6.0, from the plain STEP) · Ray
lm25118mhe-hero.glb lm25118mhe: hero from the plain model · Ray
lm25118mhe-hero.overlay.json lm25118mhe: hero from the plain model · Ray
lm25118mhe.glb plain STEP: one free product with face colours (generated model was nested; tscircuit read it white) · Ray
lm25118mhe.kicad_mod Publish 0.1.0 · Ray
lm25118mhe.kicad_sym Publish 0.1.0 · Ray
lm25118mhe.lbr Publish 0.1.0 · Ray
lm25118mhe.step plain STEP: one free product with face colours (generated model was nested; tscircuit read it white) · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Initial commit: component/lm25118mhe · Ray

LM25118MHE

Texas Instruments · DC-DC Controllers · HTSSOP-20-EP

LM25118MHE from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply voltage, operating range 3V to 42V (5V minimum for startup).
2 UVLO input Undervoltage lockout threshold monitor; below 1.23V disables regulator, use external divider to set VIN threshold.
3 RT input Oscillator frequency setting; connect resistor to AGND for 50kHz to 500kHz switching frequency.
4 EN input Enable input; below 0.5V enters shutdown with <10µA quiescent current, above 3V enables normal operation.
5 RAMP input Ramp slope control; connect external capacitor to AGND for emulated current mode control.
6 AGND power_in Analog ground reference for low-signal circuits.
7 SS input Soft-start control; external capacitor sets error amplifier reference rise time and is discharged on fault.
8 FB input Feedback signal input; compared against 1.23V reference for output voltage regulation.
9 COMP output Error amplifier output; connect loop compensation network between COMP and FB pins.
10 VOUT input Output voltage monitor input; connect directly to regulated output for emulated current mode control.
11 SYNC input Synchronization input; external clock at frequency greater than internal oscillator frequency locks switching.
12 CS input Current sense input; voltage across external sense resistor determines cycle-by-cycle current limit threshold.
13 CSG power_in Current sense ground; Kelvin-connect ground side of external sense resistor for accurate current measurement.
14 PGND power_in Power ground return path for high-current switching circuits and external MOSFET/diode grounds.
15 LO output Low-side boost MOSFET gate driver output; supplies 2.7A sink and 2.2A source current.
16 VCC power_in Bias regulator output; 7V typical at high VIN or tracks VIN at low VIN, 35mA maximum sourcing capability.
17 VCCX power_in Optional external bias supply input; voltage greater than 3.85V disables internal regulator and reduces IC power dissipation.
18 HB input Bootstrap capacitor positive node; place 0.1µF to 0.47µF ceramic capacitor between HB and HS for high-side gate drive supply.
19 HO output High-side buck MOSFET gate driver output; supplies 3.5A sink and 2.2A source current.
20 HS input High-side buck MOSFET source reference node; connect to MOSFET source and bootstrap capacitor, maintain HB-HS below 15V.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20-EP
Category Power Supply Chip
Pins 21

CAD (KiCad official)

  • Symbol: LM25118MHE
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: lm25118mhe-etched.step / lm25118mhe-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm25118mhe.step / lm25118mhe.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (45 pp, sha256 e7032a33be01a68b, retrieved 2026-10-01, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF