Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM25011Q1MYX

Texas Instruments · DC-DC Converters · MSOP-10-EP

LM25011Q1MYX from Texas Instruments, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply voltage with an operating range of 6 V to 42 V and 45 V transient capability; a low-ESR capacitor must be placed as close as possible to the VIN and SGND pins.
2 RT input On-time control pin where an external resistor from VIN sets the buck switch on-time and switching frequency, with RT to SGND rated -0.3 V to 1 V.
3 PGD output Power-good logic output that indicates when FB has risen above 95% of the internal reference with hysteresis, and requires an external pull-up resistor to a voltage less than 7 V.
4 SS input Soft-start pin where an internal current source charges an external capacitor to provide the soft-start function, with SS to SGND rated -0.3 V to 3 V.
5 SGND power_in Signal ground for all internal circuitry other than the current limit sense circuit.
6 FB input Feedback input connected internally to the regulation comparator with a regulation level of 2.51 V, with FB to SGND rated -0.3 V to 7 V.
7 CSG power_in Current sense ground connected to ground and to the current sense resistor, with CSG to SGND rated -0.3 V to 0.3 V.
8 CS input Current sense input connected to the current sense resistor and the anode of the free-wheeling diode, with CS to CSG rated -0.3 V to 0.3 V.
9 SW output Switching node connected internally to the buck switch source and externally to the inductor, free-wheeling diode cathode and bootstrap capacitor, with steady-state SW to SGND rated -1.5 V to 45 V.
10 BST input Bootstrap capacitor connection for the buck switch gate driver, where a 0.1 µF capacitor connects from SW to this pin, with BST to SW rated -0.3 V to 7 V.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package MSOP-10-EP
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN to SGND (TJ = 25°C) 45 V TJ = 25°C 4
BST to SGND 52 V 4
SW to SGND -1.5 45 V Steady State 4
BST to SW -0.3 7 V 4
CS to CSG -0.3 0.3 V 4
CSG to SGND -0.3 0.3 V 4
PGD to SGND -0.3 7 V 4
SS to SGND -0.3 3 V 4
RT to SGND -0.3 1 V 4
FB to SGND -0.3 7 V 4
Junction Temperature 150 °C 4
Storage temperature range (LM25011-Q1) Tstg -65 150 °C 4
Electrostatic discharge, Human body model (HBM) (LM25011-Q1) V(ESD) 2000 V per AEC Q100-002 4
Electrostatic discharge, Charged device model (CDM), corner pins (1, 5, 6, and 10) (LM25011-Q1) V(ESD) 750 V per AEC Q100-011 4
Electrostatic discharge, Charged device model (CDM), other pins (LM25011-Q1) V(ESD) 750 V per AEC Q100-011 4
VIN Voltage 6 42 V 4
Junction Temperature -40 125 °C 4
Input operating current IIN 1200 1600 µA Non-switching, FB = 3 V 6
VIN undervoltage lock-out threshold UVLOVIN 4.6 5.3 5.9 V VIN increasing 6
Buck Switch RDS(ON) RDS(ON) 0.3 0.6 Ω ITEST = 200 mA 6
Gate Drive UVLO BST-SW UVLOGD 2.4 3.4 4.4 V 6
Shutdown threshold (SS pin) VSS-SH 70 140 mV 6
Threshold voltage at CS VILIM -146 -130 -115 mV 6
On-time tON-1 150 200 250 ns VIN = 12 V, RT = 50 kΩ 6
On-time tON-5 130 171 215 ns VIN = 9 V, RT = 30.9 kΩ 6
On-time tON-6 105 137 170 ns VIN = 12 V, RT = 30.9 kΩ 6
On-time tON-7 79 109 142 ns VIN = 16 V, RT = 30.9 kΩ 6
Minimum off-time (LM25011) tOFF 90 150 208 ns 6
FB regulation threshold VREF 2.46 2.51 2.56 V SS pin = steady state 6
Threshold at FB, with respect to VREF 91 95 % FB increasing 6
Low state voltage (PGD) PGDVOL 125 180 mV IPGD = 1 mA, FB = 0 V 6
Junction-to-ambient thermal resistance RθJA 48 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 54.3 °C/W 5
Junction-to-board thermal resistance RθJB 34.2 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 10 °C/W 5

CAD (KiCad official)

  • Symbol: LM25011Q1MYX
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: lm25011q1myx-etched.step / lm25011q1myx-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm25011q1myx.step / lm25011q1myx.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (32 pp, sha256 6546c1245706a473, retrieved 2026-10-30, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF