component
LED6000PHTR
Public Made by Adomby adom
STMicroelectronics LED Drivers, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# LED6000PHTR++**STMicroelectronics** · LED Drivers · HTSSOP-16-EP++LED6000PHTR from STMicroelectronics, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBIAS | power_in | Auxiliary input that can be used to supply a part of the analog circuitry to increase efficiency at light-load; connect to GND if not used or bypass with 1 µF ceramic capacitor if supplied by auxiliary rail. |+| 2 | VIN | power_in | DC input voltage. |+| 3 | VIN | power_in | DC input voltage. |+| 4 | VCC | power_in | Filtered DC input voltage to the internal circuitry; bypass to signal GND by 1 µF ceramic capacitor. |+| 5 | EN | input | Active high enable pin; connect to VCC pin if not used. |+| 6 | SS | passive | An internal current generator (5 µA typ.) charges the external capacitor to implement soft-start. |+| 7 | SYNCH | bidirectional | Master/slave synchronization for preventing beating noise in low-noise applications or reducing input current RMS value. |+| 8 | COMP | output | Output of error amplifier; compensation network is connected at this pin. |+| 9 | FB | input | Inverting input of error amplifier. |+| 10 | FSW | input | A pull-down resistor to GND selects the switching frequency. |+| 11 | ILIM | input | A pull-down resistor to GND selects the peak current limitation. |+| 12 | DIM | input | A PWM signal in this input pin implements LED PWM current dimming; pulled-down by internal 2 µA current. |+| 13 | LX | passive | Switching node. |+| 14 | LX | passive | Switching node. |+| 15 | BOOT | passive | Connect external capacitor (100 nF typ.) between BOOT and LX pins; gate charge required to drive internal n-DMOS is recovered by internal regulator during off-time. |+| 16 | GND | power_in | Signal GND. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | HTSSOP-16-EP |+| Category | Nixie Tube Driver/LED Driver |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `LED6000PHTR`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `led6000phtr-etched.step` / `led6000phtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `led6000phtr.step` / `led6000phtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588940445157744640) (49 pp, sha256 `e36c28bbf8e83b45`, retrieved 2026-10-07, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/led6000phtr-datasheet.pdf)
page.jsonadded+255@@ -0,0 +1,255 @@+{+ "slug": "led6000phtr",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics LED Drivers, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "nixie tube driver-led driver",+ "led6000phtr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "led6000phtr.kicad_sym",+ "led6000phtr.kicad_mod",+ "led6000phtr.glb",+ "led6000phtr.step",+ "led6000phtr.lbr",+ "docs/hero.png",+ "docs/led6000phtr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "led6000phtr-hero.glb",+ "led6000phtr-hero.overlay.json"+ ],+ "component": {+ "mpn": "LED6000PHTR",+ "manufacturer": "STMicroelectronics",+ "package": "HTSSOP-16-EP",+ "pin_count": 17,+ "category": "Nixie Tube Driver/LED Driver",+ "subcategory": "LED Drivers",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588940445157744640",+ "parts": {+ "symbol": "led6000phtr.kicad_sym",+ "footprint": "led6000phtr.kicad_mod",+ "model_3d": "led6000phtr-hero.glb",+ "model_3d_plain": "led6000phtr.glb",+ "model_3d_step": "led6000phtr-etched.step",+ "model_3d_step_plain": "led6000phtr.step",+ "lbr": "led6000phtr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2679383",+ "digikey": "497-LED6000PHTR-ND",+ "mouser": "511-LED6000PHTR"+ },+ "distributor_check": {+ "checked_at": "2026-10-07T07:17:44Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-LED6000PHTR-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "511-LED6000PHTR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "VBIAS",+ "type": "power_in",+ "description": "Auxiliary input that can be used to supply a part of the analog circuitry to increase efficiency at light-load; connect to GND if not used or bypass with 1 µF ceramic capacitor if supplied by auxiliary rail."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "DC input voltage."+ },+ {+ "number": "3",+ "name": "VIN",+ "type": "power_in",+ "description": "DC input voltage."+ },+ {+ "number": "4",+ "name": "VCC",+ "type": "power_in",+ "description": "Filtered DC input voltage to the internal circuitry; bypass to signal GND by 1 µF ceramic capacitor."+ },+ {+ "number": "5",+ "name": "EN",+ "type": "input",+ "description": "Active high enable pin; connect to VCC pin if not used."+ },+ {+ "number": "6",+ "name": "SS",+ "type": "passive",+ "description": "An internal current generator (5 µA typ.) charges the external capacitor to implement soft-start."+ },+ {+ "number": "7",+ "name": "SYNCH",+ "type": "bidirectional",+ "description": "Master/slave synchronization for preventing beating noise in low-noise applications or reducing input current RMS value."+ },+ {+ "number": "8",+ "name": "COMP",+ "type": "output",+ "description": "Output of error amplifier; compensation network is connected at this pin."+ },+ {+ "number": "9",+ "name": "FB",+ "type": "input",+ "description": "Inverting input of error amplifier."+ },+ {+ "number": "10",+ "name": "FSW",+ "type": "input",+ "description": "A pull-down resistor to GND selects the switching frequency."+ },+ {+ "number": "11",+ "name": "ILIM",+ "type": "input",+ "description": "A pull-down resistor to GND selects the peak current limitation."+ },+ {+ "number": "12",+ "name": "DIM",+ "type": "input",+ "description": "A PWM signal in this input pin implements LED PWM current dimming; pulled-down by internal 2 µA current."+ },+ {+ "number": "13",+ "name": "LX",+ "type": "passive",+ "description": "Switching node."+ },+ {+ "number": "14",+ "name": "LX",+ "type": "passive",+ "description": "Switching node."+ },+ {+ "number": "15",+ "name": "BOOT",+ "type": "passive",+ "description": "Connect external capacitor (100 nF typ.) between BOOT and LX pins; gate charge required to drive internal n-DMOS is recovered by internal regulator during off-time."+ },+ {+ "number": "16",+ "name": "GND",+ "type": "power_in",+ "description": "Signal GND."+ },+ {+ "number": "17",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "exposed pad 17 added from the footprint",+ "dropped thermal pad ['EP'] absent from footprint"+ ],+ "pages_sent": 12,+ "cost_usd": 0.1361,+ "at": "2026-10-07T07:17:27"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588940445157744640",+ "pages": 49,+ "sha256": "e36c28bbf8e83b45",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "led6000phtr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "7982746831c0bd23f4690608869ad67776faae5c762fb0376666126a3998921b",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "led6000phtr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "3152904467cd7ea1843f0fa76c3085f1afb3bda23b3ccf489e275e10352a2ec2",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}