Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LD8105GL

Leadtrend Tech · AC-DC Controllers & Regulators · SOT-26

LD8105GL from Leadtrend Tech, in a SOT-26. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 ISEN input Current sense pin and the inverting input of the current loop op amp; absolute maximum rating is -0.3 to 6V.
2 GND power_in Ground reference pin for the device.
3 VSEN input Voltage sense pin that can sense the output voltage when connected to the midpoint of a resistor divider; absolute maximum rating is -0.3 to 6V and the voltage loop reference is 1.210V typical.
4 IREF input Non-inverting input of the current loop op amp; absolute maximum rating is -0.6 to 6V and the current loop reference is 100mV typical (97 to 103mV).
5 OUT output Common output pin of the two internal op amps; output is limited to -0.3V to VCC, maximum sink current is 20mA, and output low level is 400mV maximum at 2mA sink.
6 VCC power_in Supply voltage pin with a 3V to 38V operating range (40V maximum rating); a 0.1F bypass capacitor is required between VCC and GND.

Key specifications

Parameter Value
Manufacturer Leadtrend Tech
Package SOT-26
Category Power Supply Chip
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (recommended operating) Vcc 3 38 V 4
Supply Voltage Vcc -0.3 40 V 4
VSEN voltage VSEN -0.3 6 V 4
ISEN voltage ISEN -0.3 6 V 4
IREF voltage IREF -0.6 6 V 4
OUT voltage OUT -0.3 V upper limit printed as Vcc 4
Maximum sink current 20 mA 4
Maximum Junction Temperature 125 C 4
Operating Junction Temperature -40 125 C 4
Operating Ambient Temperature -40 85 C 4
Storage Temperature Range -65 150 C 4
Package Thermal Resistance 250 C/W 4
Power Dissipation 160 mW At Ambient Temperature = 85C 4
Lead temperature (soldering) 260 C 10 sec 4
ESD Voltage Protection, Human Body Model 2 KV Human Body Model 4
ESD Voltage Protection, Machine Model 200 V Machine Model 4
Supply Voltage 3 38 V 5
Quiescent Current 150 μA ISEN = IREF = 0V, OUT = open 5
Voltage loop reference voltage, VSEN VSEN 1.198 1.21 1.222 V ISEN = IREF = 0V 5
Voltage loop reference voltage, VSEN (temperature range) VSEN 1.186 1.234 V ISEN = IREF= 0V, (TA = -20C ~125C) 5
Voltage Loop Input Bias Current 20 nA VSEN = 1.18V~1.24V 5
Current loop reference voltage, IREF IREF 97 100 103 mV VSEN = 1.21V 5
Current Loop Input Bias Current 20 nA IREF= 90mV~110mV 5
Output Low Level 200 400 mV @2mA sink current 5

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: LD8105GL
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-26, generated on the KiCad land (body 1.6 x 2.896 mm, terminals on the pads, 1.45 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ld8105gl-etched.step / ld8105gl-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ld8105gl.step / ld8105gl.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Leadtrend Tech datasheet (8 pp, sha256 1ab7172422fcfb92, retrieved 2026-11-13, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF