main
History Download
Ray Publish 0.1.0 1d8598c

LAN9253-V

MICROCHIP TECHNOLOGY / ATMEL · Global Sourcing Parts · QFN-64(9x9)

LAN9253-V from MICROCHIP TECHNOLOGY / ATMEL, in a QFN-64(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OSCI input External 25 MHz crystal input that can also be over-driven by a single-ended clock oscillator, in which case OSCO is left unconnected.
2 OSCO output External 25 MHz crystal output.
3 OSCVDD12 power_in Crystal +1.2 V power supply, supplied by the on-chip regulator unless configured for regulator off mode via the REG_EN pin.
4 OSCVSS power_in Crystal ground.
5 VDD33 power_in +3.3 V power supply for the internal regulators, which must be supplied even if the internal regulators are disabled.
6 VDDCR power_in +1.2 V digital core supply (regulator output pin) supplied by the on-chip regulator unless regulator off mode is set, with 1 µF and 470 pF decoupling capacitors in parallel to ground.
7 REG_EN input Regulator enable; when tied to 3.3 V the internal 1.2 V regulators are enabled.
8 CLK_25/CLK_25_EN/XTAL_MODE bidirectional 25 MHz clock output (O8) and multi-level strap input: below 0.8 V disables CLK_25 and selects the crystal amplifier, 1.5 V enables CLK_25 with the crystal amplifier, above 2.2 V enables CLK_25 with Schmitt trigger input on OSCI.
9 ERRLED/PME/100FD_B/LEDPOL4 bidirectional ERR LED open-drain/open-source output (OD12/OS12) or PME output, which also latches the 100FD_B and LEDPOL4 straps at reset.
10 WAIT_ACK/PME/LATCH0/EE_EMUL_SPI3 bidirectional Host bus wait/acknowledge output (VO8/VOD8, tri-state when not selected), PME or LATCH0 function, with the EE_EMUL_SPI3 strap (pull-down) selecting the Beckhoff SPI Data Out sample mode.
11 RST# bidirectional Active-low system reset input with internal pull-up that may be left unconnected, and also driven low as an output during POR or an EtherCAT reset command.
12 D2/AD2/SOF/SIO2/EE_EMUL_SPI0 bidirectional Host bus data/address-data bit 2, Start of Frame output, SPI/SQI SIO2, or EE_EMUL_SPI0 strap, depending on mode.
13 D1/AD1/EOF/SO/SIO1 bidirectional Host bus data/address-data bit 1, End of Frame output, SPI serial data output SO or SQI SIO1, depending on mode.
14 VDDIO power_in +1.8 V to +3.3 V variable I/O power.
15 D14/AD14/DIGIO8/GPI8/GPO8/MII_TXD3/TX_SHIFT1 bidirectional Host bus data/address-data bit 14, digital I/O, GPI/GPO 8 or MII transmit data 3 (VO8), which carries the TX_SHIFT1 strap for MII TX timing.
16 D13/AD13/DIGIO7/GPI7/GPO7/MII_TXD2/TX_SHIFT0 bidirectional Host bus data/address-data bit 13, digital I/O, GPI/GPO 7 or MII transmit data 2 (VO8), which carries the TX_SHIFT0 strap for MII TX timing.
17 D0/AD0/WD_STATE/SI/SIO0 bidirectional Host bus data/address-data bit 0, SyncManager watchdog state output (0 means expired), SPI serial data input SI or SQI SIO0, depending on mode.
18 SYNC1/LATCH1/PME bidirectional Distributed Clock SYNC1 output (VO8/VOD8/VOS8) or LATCH1 input, also mappable as the PME output, not driven until the EEPROM is loaded.
19 D9/AD9/LATCH_IN/SCK bidirectional Host bus data/address-data bit 9, external data latch input LATCH_IN, or SPI/SQI serial clock input SCK, depending on mode.
20 VDDIO power_in +1.8 V to +3.3 V variable I/O power.
21 D12/AD12/DIGIO6/GPI6/GPO6/MII_TXD1/100FD_B bidirectional Host bus data/address-data bit 12, digital I/O, GPI/GPO 6 or MII transmit data 1 (VO8), which carries the 100FD_B strap in 3-port mode.
22 D11/AD11/DIGIO5/GPI5/GPO5/MII_TXD0/100FD_A bidirectional Host bus data/address-data bit 11, digital I/O, GPI/GPO 5 or MII transmit data 0 (VO8), which carries the 100FD_A strap in 3-port mode.
23 D10/AD10/DIGIO4/GPI4/GPO4/MII_TXEN bidirectional Host bus data/address-data bit 10, digital I/O, GPI/GPO 4 or MII transmit data enable output to the external PHY.
24 VDDCR power_in +1.2 V digital core power supply, supplied by the on-chip regulator unless regulator off mode is set.
25 A1/ALELO/OE_EXT/MII_CLK25/EE_EMUL_SPI2 bidirectional Host bus address bit 1 or address latch enable low, Output Enable input OE_EXT (low clears output data), or free-running 25 MHz MII clock output, with EE_EMUL_SPI2 strap (pull-down) setting SCS# polarity.
26 A3/BE0/DIGIO11/GPI11/GPO11/MII_RXDV bidirectional Host bus address bit 3 or byte enable 0, digital I/O, GPI/GPO 11 or MII receive data valid input from the external PHY.
27 A4/BE1/DIGIO12/GPI12/GPO12/MII_RXD0 bidirectional Host bus address bit 4 or byte enable 1, digital I/O, GPI/GPO 12 or MII receive data bit 0 from the external PHY.
28 CS/DIGIO13/GPI13/GPO13/MII_RXD1 bidirectional Host bus chip select (normally active low), digital I/O, GPI/GPO 13 or MII receive data bit 1 from the external PHY.
29 A2/ALEHI/DIGIO10/GPI10/GPO10/LINKACTLED2/EE_EMUL_ALELO_POL/MII_LINKPOL/LEDPOL2 bidirectional Host bus address bit 2 or address latch enable high, digital I/O, GPI/GPO 10, or Link/Activity LED 2 output, with MII_LINKPOL, EE_EMUL_ALELO_POL and LEDPOL2 straps latched at reset.
30 WR/ENB/DIGIO14/GPI14/GPO14/MII_RXD2 bidirectional Host bus write strobe or data enable strobe (normally active low), digital I/O, GPI/GPO 14 or MII receive data bit 2.
31 RD/RD_WR/DIGIO15/GPI15/GPO15/MII_RXD3 bidirectional Host bus read strobe or read/write direction control, digital I/O, GPI/GPO 15 or MII receive data bit 3.
32 VDDIO power_in +1.8 V to +3.3 V variable I/O power.
33 A0/D15/AD15/DIGIO9/GPI9/GPO9/MII_RXER bidirectional Host bus address bit 0 shared with data bit 15 or address/data bit 15, digital I/O, GPI/GPO 9 or MII receive error input from the external PHY.
34 SYNC0/LATCH0/PME bidirectional Distributed Clock SYNC0 output (VO8/VOD8/VOS8) or LATCH0 input, also mappable as the PME output, not driven until the EEPROM is loaded.
35 D3/AD3/WD_TRIG/SIO3/EE_EMUL_SPI1 bidirectional Host bus data/address-data bit 3, SyncManager watchdog trigger output, or SQI SIO3, with EE_EMUL_SPI1 strap (pull-up) configuring the SPI mode.
36 D6/AD6/DIGIO0/GPI0/GPO0/MII_RXCLK bidirectional Host bus data/address-data bit 6, digital I/O, GPI/GPO 0 or MII receive clock input from the external PHY.
37 VDDIO power_in +1.8 V to +3.3 V variable I/O power.
38 VDDCR power_in +1.2 V digital core power supply, supplied by the on-chip regulator unless regulator off mode is set.
39 D7/AD7/DIGIO1/GPI1/GPO1/MII_MDC bidirectional Host bus data/address-data bit 7, digital I/O, GPI/GPO 1 or MII serial management clock output (VO8) to the external PHY.
40 D8/AD8/DIGIO2/GPI2/GPO2/MII_MDIO bidirectional Host bus data/address-data bit 8, digital I/O, GPI/GPO 2 or MII serial management data input/output, which requires an external pull-up.
41 TESTMODE input Test mode select that must be tied to VSS for proper operation.
42 EESDA/TMS/EE_EMUL1 bidirectional EEPROM I2C serial data input/open-drain output that must be pulled up externally at all times, also JTAG TMS and EE_EMUL1 strap.
43 EESCL/TCK/EE_EMUL2 bidirectional EEPROM I2C clock input/open-drain output that must be pulled up externally when an EEPROM is used, also JTAG TCK and EE_EMUL2 strap.
44 IRQ/LATCH1 bidirectional Interrupt request output (VO8/VOD8) with programmable polarity, source and buffer type, or LATCH1 input in Digital I/O mode.
45 RUNLED/STATE_RUNLED/E2PSIZE/EE_EMUL0/LEDPOL3 bidirectional RUN or STATE_RUN LED open-drain/open-source output (VOD12/VOS12), also latching the E2PSIZE, EE_EMUL0 and LEDPOL3 straps at reset.
46 LINKACTLED1/TDI/CHIP_MODE1/LEDPOL1 bidirectional Link/Activity LED 1 open-drain/open-source output, JTAG TDI input, with CHIP_MODE1 and LEDPOL1 straps latched at reset.
47 VDDIO power_in +1.8 V to +3.3 V variable I/O power.
48 LINKACTLED0/TDO/CHIP_MODE0/100FD_A/LEDPOL0 bidirectional Link/Activity LED 0 open-drain/open-source output or JTAG TDO output (VO12), with CHIP_MODE0, 100FD_A and LEDPOL0 straps latched at reset.
49 D4/AD4/DIGIO3/GPI3/GPO3/MII_LINK bidirectional Host bus data/address-data bit 4, digital I/O, GPI/GPO 3 or MII link status input indicating a 100 Mbit/s full-duplex link, with polarity set by MII_LINKPOL.
50 D5/AD5/OUTVALID/SCS# bidirectional Host bus data/address-data bit 5, OUTVALID output marking valid outputs, or active-low SPI/SQI slave chip select input SCS#.
51 VDD33TXRX1 power_in +3.3 V Port A analog power supply.
52 TXNA bidirectional Port A twisted pair transmit/receive negative channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
53 TXPA bidirectional Port A twisted pair transmit/receive positive channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
54 RXNA bidirectional Port A twisted pair transmit/receive negative channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
55 RXPA bidirectional Port A twisted pair transmit/receive positive channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
56 VDD12TX1 power_in Port A transmitter +1.2 V supply from VDDCR, which must be tied to VDD12TX2 for proper operation.
57 RBIAS passive Internal bias reference connected to an external 12.1 kOhm, 1% resistor to ground, with a nominal 1.2 V that dissipates approximately 1 mW.
58 VDD33BIAS power_in +3.3 V master bias power supply.
59 VDD12TX2 power_in Port B transmitter +1.2 V supply from VDDCR, which must be tied to VDD12TX1 for proper operation.
60 RXPB bidirectional Port B twisted pair transmit/receive positive channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
61 RXNB bidirectional Port B twisted pair transmit/receive negative channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
62 TXPB bidirectional Port B twisted pair transmit/receive positive channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
63 TXNB bidirectional Port B twisted pair transmit/receive negative channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection.
64 VDD33TXRX2 power_in +3.3 V Port B analog power supply.
65 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer MICROCHIP TECHNOLOGY / ATMEL
Package QFN-64(9x9)
Category Global Sourcing Parts
Pins 65

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (VDD12TX1, VDD12TX2, OSCVDD12, VDDCR) 0 1.5 V Note 1 381
Supply Voltage (VDD33TXRX1, VDD33TXRX2, VDD33BIAS, VDD33, VDDIO) 0 3.6 V Note 1 381
Ethernet Magnetics Supply Voltage -0.5 3.6 V 381
Negative voltage on signal pins, with respect to ground -0.5 V Note 3 381
Positive voltage on OSCI, with respect to ground 3.6 V 381
Storage Temperature -55 150 °C 381
Junction Temperature 150 °C 381
Supply Voltage (VDD12TX1, VDD12TX2, OSCVDD12, VDDCR) 1.14 1.26 V 381
Analog Port Supply Voltage (VDD33TXRX1, VDD33TXRX2, VDD33BIAS, VDD33) 3 3.6 V 381
I/O Supply Voltage (VDDIO) 1.62 3.6 V Note 1 381
Ethernet Magnetics Supply Voltage 2.25 3.6 V 381
Ambient Operating Temperature in Still Air (commercial version) TA 0 70 °C Note 4: commercial version 381
Ambient Operating Temperature in Still Air (industrial version) TA -40 85 °C Note 4: industrial version 381
Ambient Operating Temperature in Still Air (extended industrial version) TA -40 105 °C Note 4: extended industrial version 381
Overshoot and Undershoot VOS 5 % 388
Jitter 1.4 ns Note 25 388
Peak Differential Output Voltage High VPPH 950 1050 mVpk Note 23 388
Signal Amplitude Symmetry VSS 98 102 % Note 23 388
Signal Rise and Fall Time TRF 3 5 ns Note 23 388
Rise and Fall Symmetry TRFS 0.5 ns Note 23 388
Duty Cycle Distortion DCD 35 50 65 % Note 24 388
Transmitter Peak Differential Output Voltage VOUT 2.2 2.5 2.8 V Note 26 388
Receiver Differential Squelch Threshold VDS 300 420 585 mV 388
Crystal Frequency Ffund 25 MHz Fundamental mode 394
802.3 Frequency Tolerance at 25oC Ftol -40 40 ppm Note 28 394
802.3 Frequency Stability Over Temp Ftemp -40 40 ppm Note 28 394
EtherCAT Frequency Tolerance at 25oC Ftol -15 15 ppm Note 31 394
EtherCAT Frequency Stability Over Temp Ftemp -15 15 ppm Note 31 394
Shunt Capacitance CO 7 pF 394
Load Capacitance CL 18 pF 394
Drive Level PW 300 µW Note 33 394
Equivalent Series Resistance R1 100 Ω 394
Crystal operation output duty cycle 44 57 % Note 37 395
Junction to Ambient thermal resistance, still air JA 25.6 °C/W Measured in still air 382
Junction to Ambient thermal resistance, airflow 1 m/s JA 22.3 °C/W Airflow 1 m/s 382
Junction to Ambient thermal resistance, airflow 2.5 m/s JA 20 °C/W Airflow 2.5 m/s 382
Junction to Bottom of Case thermal resistance JT 0.2 °C/W Measured in still air 382
Junction to Top of Case thermal resistance JC 2.6 °C/W 382

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing abs slicer error 100BASE-TX is +/-32. A higher absolute slicer error means a degraded signal receiving condition. 200
contacts copper The ERRLED pin on the LAN9252 functioned as the fiber mode signal detect as well as the Port A FX-SD Enable. For copper twisted pair operation, this pin would either be tied to or pulled down to groun 275

CAD (KiCad official)

  • Symbol: LAN9253-V
  • Footprint: Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm
  • 3D model: QFN-64(9x9) (KiCad packages3D, STEP)
  • 3D model files: lan9253-v-etched.step / lan9253-v-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lan9253-v.step / lan9253-v.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: MICROCHIP TECHNOLOGY / ATMEL datasheet (402 pp, sha256 2e11a3736937eb96, retrieved 2026-11-07, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF