by adom
Microchip LAN7800 — single-chip SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet controller with integrated USB device controller + PHY, Ethernet MAC, and Gigabit PHY. QFN-48 in 7x7 mm (Y9X) and 6x6 mm (VSX).
← Commit history
README.mdadded+164@@ -0,0 +1,164 @@+# LAN7800 — SuperSpeed USB 3.1 to Gigabit Ethernet Controller++## Summary++The **Microchip LAN7800** is a high-performance, single-chip **SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet** bridge controller. It integrates a USB 3.1 Gen 1 device controller and PHY, a 10/100/1000 Ethernet MAC, and a Gigabit Ethernet PHY with HP Auto-MDIX into a single 48-pin QFN, delivering a complete USB-to-Ethernet solution for docking stations, dongles, notebooks, set-top boxes and embedded systems.++On the host side it supports **SuperSpeed (5 Gbps)**, High-Speed (480 Mbps) and Full-Speed (12 Mbps) with four endpoints and remote wakeup. On the network side it is fully compliant with **IEEE 802.3 / 802.3u / 802.3ab / 802.3az**, supporting 10BASE-T / 100BASE-TX / 1000BASE-T, 802.1q VLAN tagging, 9 KB jumbo frames, and hardware IPv4/IPv6/TCP/UDP checksum offload. Low-power operation is provided through Energy Efficient Ethernet, Wake-on-LAN and NetDetach (automatic USB attach/detach when the Ethernet cable is connected or removed). The device is configured entirely through on-chip **OTP memory** — no external EEPROM required — and ships with drivers for Windows, Linux, macOS, uBoot, UEFI, PXE and FreeBSD.++### Features++- **Single-chip** SuperSpeed USB 3.1 Gen 1 → 10/100/1000 Ethernet controller+- Integrated **Gigabit Ethernet PHY** with HP Auto-MDIX, auto-negotiation and automatic polarity correction+- Integrated **10/100/1000 Ethernet MAC** (full-duplex support; full-duplex only at 1000 Mbps)+- Integrated **USB 3.1 Gen 1 SuperSpeed** device controller + PHY — SS (5 Gbps) / HS (480 Mbps) / FS (12 Mbps), 4 endpoints, remote wakeup+- **Energy Efficient Ethernet** (IEEE 802.3az) and **Wake-on-LAN**+- **NetDetach** — automatic USB attach/detach on cable connect/remove+- Configuration via on-chip **One-Time-Programmable (OTP) memory**+- **8 GPIOs**, flexible link/activity LEDs, multiple power-management modes+- Variable I/O supply **1.8–3.3 V**; internal switching + linear regulators+- 802.1q VLAN tagging, 9 KB jumbo frames, IPv4/IPv6/TCP/UDP checksum offload, 32 wake-up frame patterns+- Broad driver support: **Windows 7/8/8.1/10, Linux, macOS, uBoot, UEFI, PXE, FreeBSD**+- Two package options — **48-pin QFN 7×7 mm (Y9X)** and **48-pin QFN 6×6 mm (VSX)** — in commercial and industrial temperature grades++---++## Symbol & Footprint++### Schematic symbol++<iframe src="https://wiki.adom.inc/api/v1/pages/adom/lan7800/files/viewer-symbol.html" width="100%" height="560" style="border:0" loading="lazy" title="LAN7800 schematic symbol viewer"></iframe>++### Footprint++Two package footprints are available — use the toggle at the **top right** to switch between the **QFN 7×7 mm (Y9X)** and **QFN 6×6 mm (VSX)** variants.++<iframe src="https://wiki.adom.inc/api/v1/pages/adom/lan7800/files/viewer-footprints.html" width="100%" height="600" style="border:0" loading="lazy" title="LAN7800 footprint viewer (Y9X / VSX)"></iframe>++---++## Pin Mapping++48 signal pins plus the exposed thermal pad (pin 49, VSS). The mapping below matches the schematic symbol and both footprints.++| Pin | Name | Function | Group |+|----:|------|----------|-------|+| 1 | `TR0P` | Gigabit Ethernet MDI pair 0 (+) | Ethernet PHY |+| 2 | `TR0N` | Gigabit Ethernet MDI pair 0 (−) | Ethernet PHY |+| 3 | `VDD25A` | Power — 2.5 V analog | Power |+| 4 | `TR1P` | Gigabit Ethernet MDI pair 1 (+) | Ethernet PHY |+| 5 | `TR1N` | Gigabit Ethernet MDI pair 1 (−) | Ethernet PHY |+| 6 | `VDD25A` | Power — 2.5 V analog | Power |+| 7 | `TR2P` | Gigabit Ethernet MDI pair 2 (+) | Ethernet PHY |+| 8 | `TR2N` | Gigabit Ethernet MDI pair 2 (−) | Ethernet PHY |+| 9 | `VDD25A` | Power — 2.5 V analog | Power |+| 10 | `TR3P` | Gigabit Ethernet MDI pair 3 (+) | Ethernet PHY |+| 11 | `TR3N` | Gigabit Ethernet MDI pair 3 (−) | Ethernet PHY |+| 12 | `VDD25A` | Power — 2.5 V analog | Power |+| 13 | `VDD12_SW_OUT` | Power — 1.2 V switching-regulator output | Power |+| 14 | `VDD_SW_IN` | Power — Switching-regulator input | Power |+| 15 | `VDD12_SW_FB` | Power — 1.2 V switching-regulator feedback | Power |+| 16 | `EECS/GPIO0` | OTP/EEPROM chip-select (SPI) / GPIO0 | Config / GPIO |+| 17 | `EEDI/GPIO1` | OTP/EEPROM data-in (SPI) / GPIO1 | Config / GPIO |+| 18 | `EEDO/LED0/GPIO2` | OTP/EEPROM data-out (SPI) / LED0 / GPIO2 | Config / GPIO |+| 19 | `EECLK/LED1/GPIO3` | OTP/EEPROM clock (SPI) / LED1 / GPIO3 | Config / GPIO |+| 20 | `VDDVARIO` | Power — Variable I/O (1.8–3.3 V) | Power |+| 21 | `VDD12CORE` | Power — 1.2 V digital core | Power |+| 22 | `PME_N/GPIO4` | Power-management-event output / GPIO4 | LED / GPIO |+| 23 | `VBUS_DET` | USB VBUS detect input | Control |+| 24 | `SUSPEND_N/LED2/GPIO5` | Suspend indicator / LED2 / GPIO5 | LED / GPIO |+| 25 | `VDD12A` | Power — 1.2 V analog | Power |+| 26 | `USB2_DP` | USB 2.0 HS/FS data + | USB 2.0 |+| 27 | `USB2_DM` | USB 2.0 HS/FS data − | USB 2.0 |+| 28 | `USB3_TXDP` | USB 3.1 Gen 1 SuperSpeed TX + | USB 3.1 SS |+| 29 | `USB3_TXDM` | USB 3.1 Gen 1 SuperSpeed TX − | USB 3.1 SS |+| 30 | `VDD12A` | Power — 1.2 V analog | Power |+| 31 | `USB3_RXDP` | USB 3.1 Gen 1 SuperSpeed RX + | USB 3.1 SS |+| 32 | `USB3_RXDM` | USB 3.1 Gen 1 SuperSpeed RX − | USB 3.1 SS |+| 33 | `LED3/GPIO6` | LED3 / GPIO6 (link/activity LED) | LED / GPIO |+| 34 | `TEST` | Test — connect per datasheet | Control |+| 35 | `RESET_N/PME_CLEAR` | Reset / PME clear, active-low | Control |+| 36 | `VDDVARIO` | Power — Variable I/O (1.8–3.3 V) | Power |+| 37 | `USBRBIAS` | USB bias resistor reference | Analog ref |+| 38 | `VDD33A` | Power — 3.3 V analog | Power |+| 39 | `VDDVARIO` | Power — Variable I/O (1.8–3.3 V) | Power |+| 40 | `XI` | 25 MHz crystal input | Clock |+| 41 | `XO` | 25 MHz crystal output | Clock |+| 42 | `VDD12CORE` | Power — 1.2 V digital core | Power |+| 43 | `PME_MODE/GPIO7` | PME mode strap / GPIO7 | LED / GPIO |+| 44 | `VDD12A` | Power — 1.2 V analog | Power |+| 45 | `VDD25_REG_OUT` | Power — 2.5 V internal-regulator output | Power |+| 46 | `VDD33_REG_IN` | Power — 3.3 V internal-regulator input | Power |+| 47 | `REF_REXT` | PHY bias resistor reference (external R to GND) | Analog ref |+| 48 | `REF_FILT` | PHY internal-regulator filter | Analog ref |+| 49 | `VSS` | Ground (exposed thermal pad — connect to GND via field) | Ground |++---++## Component Variants++All eight orderable variants are the **identical LAN7800 silicon** — they differ only in **package body size**, **operating-temperature grade**, and **shipping/packaging**. There are no functional or electrical differences between them; choose by mechanical footprint and temperature range.++### QFN 7×7 mm — package code **Y9X** *(default on this page)*++0.5 mm pitch · 5.3 × 5.3 mm exposed pad · 1.0 mm body height.++| Order code | Packaging | Temperature grade |+|------------|-----------|-------------------|+| `LAN7800/Y9X` | Tray | Commercial (0 °C to +70 °C) |+| `LAN7800T/Y9X` | Tape & Reel | Commercial (0 °C to +70 °C) |+| `LAN7800-I/Y9X` | Tray | Industrial (−40 °C to +85 °C) |+| `LAN7800T-I/Y9X` | Tape & Reel | Industrial (−40 °C to +85 °C) |++### QFN 6×6 mm — package code **VSX**++0.4 mm pitch · 4.3 × 4.3 mm exposed pad · 0.9 mm body height. Same pinout; smaller board area for space-constrained designs.++| Order code | Packaging | Temperature grade |+|------------|-----------|-------------------|+| `LAN7800/VSX` | Tray | Commercial (0 °C to +70 °C) |+| `LAN7800T/VSX` | Tape & Reel | Commercial (0 °C to +70 °C) |+| `LAN7800-I/VSX` | Tray | Industrial (−40 °C to +85 °C) |+| `LAN7800T-I/VSX` | Tape & Reel | Industrial (−40 °C to +85 °C) |++**Order-code legend:** `LAN7800` `[T]` `[-I]` `/` `{Y9X|VSX}` — `T` = Tape & Reel (blank = tray), `-I` = Industrial (blank = Commercial), `Y9X` = 7×7 mm / `VSX` = 6×6 mm.++---++## Datasheet++<iframe src="https://wiki.adom.inc/api/v1/pages/adom/lan7800/files/lan7800-datasheet.pdf" width="100%" height="820" style="border:0" title="LAN7800 datasheet"></iframe>++[Download the full datasheet (PDF)](lan7800-datasheet.pdf) · Microchip DS00001992++---++## Assets++Preview or download the CAD libraries — switch between **KiCad**, **Fusion 360** and **Altium** — plus the 3D models.++<iframe src="https://wiki.adom.inc/api/v1/pages/adom/lan7800/files/assets.html" width="100%" height="520" style="border:0" loading="lazy" title="LAN7800 CAD assets"></iframe>++---++## Thumbnails++| Schematic symbol | Footprint — QFN 7×7 (Y9X) | Footprint — QFN 6×6 (VSX) |+|:---:|:---:|:---:|+|  |  |  |++++---++## Applications++Boards on the Adom wiki that use the LAN7800:++1. **[USB3.0 to Ethernet Molecule](https://wiki.adom.inc/adom/usb3-to-ethernet-dataonly-molecule)** — USB-C to Gigabit Ethernet (data-only) adapter on the LAN7800 (U1).++*More boards will be listed here as they are published.*++---++*Related: [LAN7800 EEPROM Programmer](https://wiki.adom.inc/adom/lan7800-programmer) · symbol/footprint/3D + canonical adom-lbr JSON in the Assets section above.*
page.jsonadded+63@@ -0,0 +1,63 @@+{+ "slug": "lan7800",+ "title": "SuperSpeed USB 3.1 to 10/100/1000 Ethernet Controller - LAN7800",+ "type": "component",+ "version": "1.0.0",+ "description": "Microchip LAN7800 — a single-chip SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet controller. Integrates a USB 3.1 device controller + PHY, a 10/100/1000 Ethernet MAC, and a Gigabit Ethernet PHY with HP Auto-MDIX. Configured via on-chip OTP memory (no external EEPROM); supports Energy Efficient Ethernet, Wake-on-LAN, NetDetach, 4 USB endpoints, 802.1q VLAN, 9 KB jumbo frames and TCP/UDP checksum offload. Offered in 48-pin QFN 7x7 mm (Y9X) and 6x6 mm (VSX), commercial and industrial grades.",+ "tags": [+ "component",+ "ic",+ "ethernet-controller",+ "usb3",+ "gigabit-ethernet",+ "lan7800",+ "microchip",+ "usb-c",+ "kicad",+ "adom-lbr"+ ],+ "component": {+ "mpn": "LAN7800",+ "manufacturer": "Microchip Technology",+ "category": "Ethernet Controller",+ "parts": {+ "model_3d": "lan7800.glb"+ },+ "model_3d_path": "lan7800.glb"+ },+ "hero": {+ "type": "billboard",+ "headline": "LAN7800",+ "subhead": "SuperSpeed USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet controller — Microchip",+ "screenshot": "screenshots/hero.png"+ },+ "dependencies": {},+ "files": [+ "README.md",+ "lan7800.kicad_sym",+ "lan7800-qfn48-7x7-y9x.kicad_mod",+ "lan7800-qfn48-6x6-vsx.kicad_mod",+ "lan7800.step",+ "lan7800.glb",+ "lan7800.adom-lbr.json",+ "lan7800.lbr",+ "lan7800.IntLib",+ "lan7800.SchLib",+ "lan7800.PcbLib",+ "lan7800-datasheet.pdf",+ "viewer-symbol.html",+ "viewer-fp-y9x.html",+ "viewer-fp-vsx.html",+ "viewer-footprints.html",+ "assets.html",+ "thumb-symbol.svg",+ "thumb-fp-y9x.svg",+ "thumb-fp-vsx.svg",+ "screenshots/hero.png"+ ],+ "org": "adom",+ "author": {+ "name": "barrett-land",+ "email": "[email protected]"+ }+}