main
Ray
Publish 0.1.0
f9fb46e
L8001G-R20-R
UTC(Unisonic Tech) · Gate Drive ICs · SSOP-20-150mil
L8001G-R20-R from UTC(Unisonic Tech), in a SSOP-20-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VD1 | output | First FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 2 | VG1 | output | First FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 3 | VD2 | output | Second FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 4 | VG2 | output | Second FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 5 | VG3 | output | Third FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 6 | VD3 | output | Third FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 7 | GND | power_in | Ground reference for the device. |
| 8 | NC | unconnected | No connect; the datasheet specifies no internal connection for this pin. |
| 9 | CNB1 | output | Oscillator output for the negative voltage generator, AC-coupled to CNB2 through a 47 nF capacitor in the typical application. |
| 10 | CNB2 | input | Rectifier input of the negative voltage generator, AC-coupled from CNB1 through a 47 nF capacitor in the typical application. |
| 11 | CSUB | power_out | Negative voltage output, bypassed with a 47 nF capacitor; the absolute maximum sink current is -500 uA. |
| 12 | RCAL1 | passive | Current-set resistor connection for FET drains VD1, VD2 and VD3; 8.2 kΩ was used in the electrical characteristics test conditions. |
| 13 | RCAL2 | passive | Current-set resistor connection for FET drains VD4, VD5 and VD6; 8.2 kΩ was used in the electrical characteristics test conditions. |
| 14 | VG6 | output | Sixth FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 15 | VD6 | output | Sixth FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 16 | VG5 | output | Fifth FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 17 | VD5 | output | Fifth FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 18 | VG4 | output | Fourth FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 19 | VD4 | output | Fourth FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 20 | VCC | power_in | Supply voltage, specified at 3.3 V to 6 V, with an absolute maximum range of -0.6 V to 8 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | UTC(Unisonic Tech) |
| Package | SSOP-20-150mil |
| Category | Power Management ICs |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | -0.6 | 8 | V | 4 | ||
| Supply Current | ICC | 100 | mA | 4 | |||
| Maximum Drain Current | ID | 15 | mA | 4 | |||
| Maximum CSUB Sink Current | ICSUB | -500 | uA | 4 | |||
| Operating Temperature | TOPR | -40 | 80 | °C | 4 | ||
| Storage Temperature | TSTG | -50 | 150 | °C | 4 | ||
| Supply Voltage | VCC | 3.3 | 6 | V | 4 | ||
| Supply Current | ICC | 10 | mA | No FET | 4 | ||
| Negative Voltage | VSUB | -3 | -2.5 | -1 | V | ISUB=0uA, VCC=6V | 4 |
| Negative Voltage | VSUB | -1 | V | ISUB=-200uA | 4 | ||
| Oscillator Frequency | fO | 200 | 350 | 800 | KHz | 4 | |
| Drain Current | ID | 8 | 10 | 12 | mA | 4 | |
| Drain Current Change with VCC | ∆IDV | 0.2 | %/V | VCC=3.3~6V | 4 | ||
| Drain Offset Current (VD1/VD2/VD3/VD4/VD5/VD6) | ∆IDC | 0.2 | mA | 4 | |||
| Drain Current Change with Temp. | ∆IDT | 0.1 | %/°C | T=-40~80°C | 4 | ||
| Drain Voltage | VD | 1.8 | 2 | 2.2 | V | ID=10mA | 4 |
| Drain Voltage Change with VCC | ∆VDV | 0.5 | %/V | VCC=3.3~6V | 4 | ||
| Drain Voltage Change | ∆VDT | 50 | ppm | T=-40~80°C | 4 | ||
| Dynamic Gate Voltage Range | VG | -2.5 | 0.7 | V | Csub without loading | 4 | |
| Drain Output Noise Voltage | Vdn | 0.05 | VPP | With drain bypass capacitor=10nF | 4 | ||
| Gate Output Noise Voltage | VGN | 0.03 | VPP | With gate bypass capacitor=10nF | 4 |
CAD (KiCad official)
- Symbol:
L8001G-R20-R - Footprint:
Package_SO:SSOP-20_3.9x8.7mm_P0.635mm - 3D model: SSOP-20-150mil (KiCad packages3D, STEP)
- 3D model files:
l8001g-r20-r-etched.step/l8001g-r20-r-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l8001g-r20-r.step/l8001g-r20-r.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: UTC(Unisonic Tech) datasheet (6 pp, sha256
257b5e9689dced26, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# L8001G-R20-R
**UTC(Unisonic Tech)** · Gate Drive ICs · SSOP-20-150mil
L8001G-R20-R from UTC(Unisonic Tech), in a SSOP-20-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VD1 | output | First FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 2 | VG1 | output | First FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 3 | VD2 | output | Second FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 4 | VG2 | output | Second FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 5 | VG3 | output | Third FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 6 | VD3 | output | Third FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 7 | GND | power_in | Ground reference for the device. |
| 8 | NC | unconnected | No connect; the datasheet specifies no internal connection for this pin. |
| 9 | CNB1 | output | Oscillator output for the negative voltage generator, AC-coupled to CNB2 through a 47 nF capacitor in the typical application. |
| 10 | CNB2 | input | Rectifier input of the negative voltage generator, AC-coupled from CNB1 through a 47 nF capacitor in the typical application. |
| 11 | CSUB | power_out | Negative voltage output, bypassed with a 47 nF capacitor; the absolute maximum sink current is -500 uA. |
| 12 | RCAL1 | passive | Current-set resistor connection for FET drains VD1, VD2 and VD3; 8.2 kΩ was used in the electrical characteristics test conditions. |
| 13 | RCAL2 | passive | Current-set resistor connection for FET drains VD4, VD5 and VD6; 8.2 kΩ was used in the electrical characteristics test conditions. |
| 14 | VG6 | output | Sixth FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 15 | VD6 | output | Sixth FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 16 | VG5 | output | Fifth FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 17 | VD5 | output | Fifth FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 18 | VG4 | output | Fourth FET gate output voltage, a negative bias with a dynamic range of -2.5 V to 0.7 V when CSUB is unloaded. |
| 19 | VD4 | output | Fourth FET drain output; the electrical characteristics give a drain voltage of 2 V typical (1.8 to 2.2 V) at ID = 10 mA. |
| 20 | VCC | power_in | Supply voltage, specified at 3.3 V to 6 V, with an absolute maximum range of -0.6 V to 8 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | UTC(Unisonic Tech) |
| Package | SSOP-20-150mil |
| Category | Power Management ICs |
| Pins | 20 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | -0.6 | | 8 | V | | 4 |
| Supply Current | ICC | | | 100 | mA | | 4 |
| Maximum Drain Current | ID | | | 15 | mA | | 4 |
| Maximum CSUB Sink Current | ICSUB | | | -500 | uA | | 4 |
| Operating Temperature | TOPR | -40 | | 80 | °C | | 4 |
| Storage Temperature | TSTG | -50 | | 150 | °C | | 4 |
| Supply Voltage | VCC | 3.3 | | 6 | V | | 4 |
| Supply Current | ICC | | | 10 | mA | No FET | 4 |
| Negative Voltage | VSUB | -3 | -2.5 | -1 | V | ISUB=0uA, VCC=6V | 4 |
| Negative Voltage | VSUB | | | -1 | V | ISUB=-200uA | 4 |
| Oscillator Frequency | fO | 200 | 350 | 800 | KHz | | 4 |
| Drain Current | ID | 8 | 10 | 12 | mA | | 4 |
| Drain Current Change with VCC | ∆IDV | | | 0.2 | %/V | VCC=3.3~6V | 4 |
| Drain Offset Current (VD1/VD2/VD3/VD4/VD5/VD6) | ∆IDC | | | 0.2 | mA | | 4 |
| Drain Current Change with Temp. | ∆IDT | | | 0.1 | %/°C | T=-40~80°C | 4 |
| Drain Voltage | VD | 1.8 | 2 | 2.2 | V | ID=10mA | 4 |
| Drain Voltage Change with VCC | ∆VDV | | | 0.5 | %/V | VCC=3.3~6V | 4 |
| Drain Voltage Change | ∆VDT | | | 50 | ppm | T=-40~80°C | 4 |
| Dynamic Gate Voltage Range | VG | -2.5 | | 0.7 | V | Csub without loading | 4 |
| Drain Output Noise Voltage | Vdn | | | 0.05 | VPP | With drain bypass capacitor=10nF | 4 |
| Gate Output Noise Voltage | VGN | | | 0.03 | VPP | With gate bypass capacitor=10nF | 4 |
## CAD (KiCad official)
- Symbol: `L8001G-R20-R`
- Footprint: `Package_SO:SSOP-20_3.9x8.7mm_P0.635mm`
- 3D model: SSOP-20-150mil (KiCad packages3D, STEP)
- 3D model files: `l8001g-r20-r-etched.step` / `l8001g-r20-r-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `l8001g-r20-r.step` / `l8001g-r20-r.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [UTC(Unisonic Tech) datasheet](docs/l8001g-r20-r-datasheet.pdf) (6 pp, sha256 `257b5e9689dced26`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/l8001g-r20-r-datasheet.pdf)