3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownL6986
STMicroelectronics · DC-DC Converters · HTSSOP-16-EP
L6986 from STMicroelectronics, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RST | output | Open collector output driven low when output voltage is out of regulation; released after adjustable time DELAY once output voltage exceeds active delay threshold. |
| 2 | VCC | power_out | Regulated LDO output (2.9-3.6 V) supplying embedded analog circuitry; requires ≥470 nF ceramic filter capacitor to GND. |
| 3 | SS/INH | input | Soft-start input with internal 4 µA charging current; open collector stage disables device when clamped to GND (INH mode). |
| 4 | SYNCH | input | Master/slave synchronization input; leave floating when not used in LNM. |
| 5 | FSW | input | Switching frequency selection via pinstrapping using pull-up to VCC or pull-down to GND (E24 series); active only before soft-start to minimize consumption. |
| 6 | MLF | input | Low noise mode/low consumption mode and active RST threshold selection via pinstrapping using pull-up to VCC or pull-down to GND (E24 series); active only before soft-start. |
| 7 | COMP | output | Error amplifier output with designed compensation network connected at this pin. |
| 8 | DELAY | input | External capacitor connected at this pin sets DELAY time to assert RST rising edge after output voltage exceeds reset threshold; floating pin makes RST behave as power-good output. |
| 9 | FB | input | Inverting input of error amplifier. |
| 10 | SGND | power_in | Signal ground reference. |
| 11 | PGND | power_in | Power ground reference. |
| 12 | PGND | power_in | Power ground reference. |
| 13 | LX | output | Switching node. |
| 14 | LX | output | Switching node. |
| 15 | VIN | power_in | DC input voltage with 4 to 38 V operating range. |
| 16 | VBIAS | input | Supply reference voltage typically connected to regulated output voltage; external voltage reference can be used to increase light-load efficiency; connect to GND if unused. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | HTSSOP-16-EP |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage (VIN) absolute maximum | VIN | -0.3 | 40 | V | 6 | ||
| DELAY pin voltage | DELAY | -0.3 | V | 6 | |||
| VCC pin voltage | VCC | -0.3 | V | 6 | |||
| SS/INH pin voltage | SS / INH | -0.3 | V | 6 | |||
| MLF pin voltage | MLF | -0.3 | V | 6 | |||
| COMP pin voltage | COMP | -0.3 | V | 6 | |||
| FB pin voltage | FB | -0.3 | V | 6 | |||
| FSW pin voltage | FSW | -0.3 | V | 6 | |||
| SYNCH pin voltage | SYNCH | -0.3 | V | 6 | |||
| VBIAS pin voltage | VBIAS | -0.3 | V | 6 | |||
| RST pin voltage | RST | -0.3 | V | 6 | |||
| Operating junction temperature range | TJ | -40 | 150 | °C | 6 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 6 | ||
| Lead temperature (soldering) | TLEAD | 260 | °C | Soldering 10 sec | 6 | ||
| High-side switch current | IHS | 2 | A | 6 | |||
| Low-side switch current | ILS | 2 | A | 6 | |||
| Thermal resistance junction to ambient | Rth JA | 40 | °C/W | Device soldered on ST demonstration board | 7 | ||
| Thermal resistance junction to exposed pad | Rth JC | 5 | °C/W | For board design (not suggested to estimate TJ from power losses) | 7 | ||
| Operating input voltage range | VIN | 4 | 38 | V | 8 | ||
| VCC UVLO rising threshold | VINH | 2.7 | 3.5 | V | 8 | ||
| VCC UVLO falling threshold | VINL | 2.5 | 3.5 | V | 8 | ||
| Skip current limit | ISKIP | 0.6 | 0.8 | A | Note (1) | 8 | |
| Reverse current limit | IVY_SNK | 0.5 | 1 | 2 | A | LNM or VOUT overvoltage | 8 |
| High-side RDSON | RDSON HS | 0.18 | 0.36 | Ω | ISW = 1 A | 8 | |
| Low-side RDSON | RDSON LS | 0.15 | 0.3 | Ω | ISW = 1 A | 8 | |
| FSW biasing current | IFSW | 0 | 500 | nA | SS ended | 8 | |
| MLF biasing current | IMLF | 0 | 500 | nA | SS ended | 8 | |
| Duty cycle | D | 0 | 100 | % | Note (2) | 8 | |
| VCC LDO output voltage | VCC | 2.9 | 3.3 | 3.6 | V | VBIAS = GND (no switchover) | 8 |
| SWO VBIAS threshold | SWO | 2.85 | 3.2 | V | Switch internal supply from VIN to VBIAS | 8 | |
| SWO VBIAS threshold | SWO | 2.8 | 3.15 | V | Switch internal supply from VBIAS to VIN | 8 | |
| Shutdown current from VIN | ISHTDWN | 4 | 8 | 15 | µA | VSS/INH = GND | 9 |
| Quiescent current from VIN, LCM with SWO | IQ OPVIN | 4 | 10 | 15 | µA | LCM - SWO, VREF < VFB < VOVP (SLEEP), VBIAS = 3.3 V; note (3) | 9 |
| Quiescent current from VIN, LCM without SWO | IQ OPVIN | 45 | 70 | 100 | µA | LCM - NO SWO, VREF < VFB < VOVP (SLEEP), VBIAS = GND; note (3) | 9 |
| Quiescent current from VIN, LNM with SWO | IQ OPVIN | 0.5 | 1.5 | 5 | mA | LNM - SWO, VFB = GND (NO SLEEP), VBIAS = 3.3 V | 9 |
| Quiescent current from VIN, LNM without SWO | IQ OPVIN | 2 | 2.8 | 6 | mA | LNM - NO SWO, VFB = GND (NO SLEEP), VBIAS = GND | 9 |
| Quiescent current from VBIAS, LCM with SWO | IQ OPVBIAS | 30 | 50 | 90 | µA | LCM - SWO, VREF < VFB < VOVP (SLEEP), VBIAS = 3.3 V; note (3) | 9 |
| Quiescent current from VBIAS, LNM with SWO | IQ OPVBIAS | 0.5 | 1.2 | 5 | mA | LNM - SWO, VFB = GND (NO SLEEP), VBIAS = 3.3 V | 9 |
| VSS threshold (SS rising) | VINH | 200 | 460 | 700 | mV | SS rising | 9 |
| SS discharge voltage | VSS_L_CLMP | 855 | 900 | 945 | mV | VCC < VCCH OR t < TSS SETUP OR thermal fail | 9 |
| Start of internal error amplifier ramp | VSS START | 0.995 | 1.1 | 1.15 | V | 9 | |
| SS/INH voltage at the end of SS phase | VSS_H_CLMP | 2.5 | 3.6 | V | 9 | ||
| Voltage feedback | VFB | 0.841 | 0.85 | 0.859 | V | 9 | |
| FB biasing current | IFB | 50 | 500 | nA | 9 | ||
| Transconductance | Gm | 85 | 155 | 210 | µS | 9 | |
| EA output current capability | ICOMP | -6 | 12 | 25 | µA | 10 | |
| Overvoltage trip (VOVP/VREF) | VOVP | 1.15 | 1.2 | 1.25 | 10 | ||
| Overvoltage hysteresis | VOVP HYST | 0.5 | 2 | 5 | % | 10 | |
| SYNCH input threshold | VSYN TH | 0.7 | 1.2 | V | LNM, SYNCH rising | 10 | |
| RST released threshold (VDELAY) | VTHD | 1.19 | 1.234 | 1.258 | V | RST released as soon as VDELAY > VTHD, VFB > VTHR | 10 |
| Slope compensation | Slope compensation | 0.4 | 0.75 | 1 | A | Note (4): measured at fSW = 250 kHz | 10 |
| RST threshold, LCM, RVCC = 0, RGND = NC | VRST | 0.779 | 0.791 | 0.802 | V | LCM; VRST/VOUT tgt 93% | 12 |
| RST threshold, LCM, RVCC = 8.2 kΩ | VRST | 0.67 | 0.68 | 0.69 | V | LCM; RVCC = 8.2 kΩ ±1%, RGND = NC; VRST/VOUT tgt 80% | 12 |
| RST threshold, LCM, RVCC = 18 kΩ | VRST | 0.728 | 0.74 | 0.751 | V | LCM; RVCC = 18 kΩ ±1%, RGND = NC; VRST/VOUT tgt 87% | 12 |
| RST threshold, LCM, RVCC = 39 kΩ | VRST | 0.804 | 0.816 | 0.828 | V | LCM; RVCC = 39 kΩ ±1%, RGND = NC; VRST/VOUT tgt 96% | 12 |
| RST threshold, LNM, RGND = 0 | VRST | 0.779 | 0.791 | 0.802 | V | LNM; RVCC = NC, RGND = 0; VRST/VOUT tgt 93% | 12 |
| RST threshold, LNM, RGND = 8.2 kΩ | VRST | 0.67 | 0.68 | 0.69 | V | LNM; RVCC = NC, RGND = 8.2 kΩ ±1%; VRST/VOUT tgt 80% | 12 |
| RST threshold, LNM, RGND = 18 kΩ | VRST | 0.728 | 0.74 | 0.751 | V | LNM; RVCC = NC, RGND = 18 kΩ ±1%; VRST/VOUT tgt 87% | 12 |
| RST threshold, LNM, RGND = 39 kΩ | VRST | 0.804 | 0.816 | 0.828 | V | LNM; RVCC = NC, RGND = 39 kΩ ±1%; VRST/VOUT tgt 96% | 12 |
CAD (KiCad official)
- Symbol:
L6986 - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
l6986-etched.step/l6986-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l6986.step/l6986.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (68 pp, sha256
59e9f81936259e74, retrieved 2026-10-06, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).