component
L6699DTR
Public Made by Adomby adom
STMicroelectronics AC-DC Controllers And Regulators, SO-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownL6699DTR
STMicroelectronics · AC-DC Controllers And Regulators · SO-16
L6699DTR from STMicroelectronics, in a SO-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CSS | passive | Soft-start capacitor and resistor connection to GND; sets initial oscillator frequency and soft-start time constant; discharged by internal switch on overcurrent (ISEN > 0.8V), capacitive-mode operation, or device shutdown. |
| 2 | DELAY | passive | Delayed shutdown capacitor and resistor connection to GND; capacitor charged by 350µA pulses on overcurrent and slowly discharged by external resistor; IC stops switching when voltage reaches 3.5V and restarts when it drops below 0.3V. |
| 3 | CF | passive | Oscillator timing capacitor connected to GND; charged and discharged by internal current generators to determine switching frequency of converter. |
| 4 | RFmin | output | Minimum oscillator frequency 2V reference output; external resistor to GND sets current for minimum frequency; maximum frequency set by phototransistor resistor; recommended maximum initial operating frequency below 300kHz. |
| 5 | STBY | input | Burst-mode threshold input sensing feedback-related voltage; compared to 1.26V internal reference; IC enters idle state when voltage below threshold and restarts when exceeding reference by 30mV. |
| 6 | ISEN | input | Current sense input from sense resistor or capacitive divider; 0.8V threshold triggers soft-start capacitor discharge for frequency increase; 1.5V threshold causes immediate shutdown with restart delay; used for capacitive-mode detection and hard-switching prevention. |
| 7 | LINE | input | Line sensing input for brownout protection via resistor divider to high voltage input; voltage below 1.25V threshold shuts down IC and discharges soft-start capacitor; includes 13µA current hysteresis; internally clamped by Zener; bypass with capacitor to GND. |
| 8 | DIS | input | Latched device shutdown input; voltage exceeding 1.85V shuts down IC and reduces consumption; latch is latched until VCC falls below UVLO threshold; used for OTP and OVP protection. |
| 9 | PFC_STOP | tri_state | Open-drain ON/OFF control output for PFC controller; pulled low when IC is shut down by DIS >1.85V, ISEN >1.5V, STBY <1.25V, or DELAY >2V; open during UVLO. |
| 10 | GND | power_in | Chip ground; current return for low-side gate-drive and IC bias current; all ground connections of bias components should tie to track connected to this pin separately from pulsed current return. |
| 11 | LVG | output | Low-side gate-drive output; capable of 0.3A minimum source and 0.8A minimum sink peak current to drive lower MOSFET of half-bridge leg; actively pulled to GND during UVLO. |
| 12 | VCC | power_in | IC supply voltage (operating range 8.85-16V after turn-on) for signal part and low-side gate driver; bypass with 0.1µF typical capacitor to GND for clean bias voltage. |
| 13 | N.C. | unconnected | High voltage spacer; not internally connected; isolates high voltage pin and eases compliance with safety regulations for creepage distance on PCB. |
| 14 | OUT | power_in | High-side gate-drive floating ground; current return for high-side gate-drive current; connection must be carefully laid out to avoid excessive spikes below ground. |
| 15 | HVG | output | High-side floating gate-drive output; capable of 0.3A minimum source and 0.8A minimum sink peak current to drive upper MOSFET of half-bridge leg; internally pulled to OUT via resistor to prevent floating during UVLO. |
| 16 | VBOOT | power_in | High-side gate-drive floating supply voltage (operating range -1 to 618V relative to OUT); bootstrap capacitor connected between this pin and OUT pin 14; fed by internal synchronous bootstrap diode driven in-phase with low-side gate-drive. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SO-16 |
| Category | Power Management (PMIC) |
| Pins | 16 |
CAD (KiCad official)
- Symbol:
L6699DTR - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SO-16 (KiCad packages3D, STEP)
- 3D model files:
l6699dtr-etched.step/l6699dtr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);l6699dtr.step/l6699dtr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (38 pp, sha256
74d555a5bc88632e, retrieved 2026-10-03, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).