L6599DTR

{
 "schema": "adom.pads/1",
 "slug": "l6599dtr",
 "footprint": "SOIC-16_3.9x9.9mm_P1.27mm",
 "generated_from": {
  "footprint": "SOIC-16_3.9x9.9mm_P1.27mm@sha256:f9b5075740f7816c",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -2.475,
   -4.445
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOIC-16_3.9x9.9mm_P1.27mm@sha256:f9b5075740f7816c"
 },
 "pad_count": 16,
 "symbol_pins": [
  "1",
  "10",
  "11",
  "12",
  "13",
  "14",
  "15",
  "16",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8",
  "9"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -4.445
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "CSS",
   "type": "passive",
   "description": "Soft-start pin. External capacitor to GND and resistor to RFmin (pin 4) set the maximum oscillator frequency and the frequency-shift time constant during start-up. Internally discharged whenever the chip turns OFF (VCC<UVLO, LINE<1.25V or >6V, DIS>1.85V, ISEN>1.5V, DELAY>3.5V) and while ISEN exceeds 0.8V (down to 0.75V) so the part always soft-starts.",
   "is_pin1": true,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -3.175
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "DELAY",
   "type": "passive",
   "description": "Delayed shutdown upon overcurrent. External RC to GND sets the maximum duration of an OCP condition (charged by an internal 150 uA current source when ISEN>0.8V) and the restart delay. IC stops switching once the pin reaches 3.5V and re-enables when the voltage falls below 0.3V, yielding hiccup-mode short-circuit protection.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "CF",
   "type": "passive",
   "description": "Timing capacitor. Charged/discharged by internal current sources programmed by the RFmin network to set the converter switching frequency.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "RFmin",
   "type": "passive",
   "description": "Minimum oscillator frequency setting. Provides a precise 2 V reference; the resistor to GND sets the minimum oscillator frequency. The optocoupler phototransistor is coupled here through a resistor to modulate the operating frequency (feedback), and an RC series to GND sets the soft-start frequency shift.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "STBY",
   "type": "input",
   "description": "Burst-mode operation threshold. Compared to an internal 1.25 V reference with 50 mV hysteresis; when the feedback-related voltage falls below the reference, the IC enters idle (burst) mode and drops to reduced quiescent current. Tie to RFmin if burst-mode is not used.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "ISEN",
   "type": "input",
   "description": "Current-sense input for two-level OCP. Above the 0.8 V threshold (50 mV hysteresis) the soft-start cap is discharged, shifting the switching frequency up to limit power. A second 1.5 V comparator latches the device off (near-zero consumption) if the current keeps rising; latch clears when VCC drops below UVLO. Tie to GND if unused.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    3.175
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "LINE",
   "type": "input",
   "description": "Line-sensing input for AC/DC brownout protection. Below 1.25 V the IC shuts down (not latched), consumption drops and the soft-start cap discharges; operation re-enables above 1.25 V. Internal 15 uA current source provides hysteresis while pin is below 1.25 V. An internal zener top-limits the pin; triggering it latches the IC OFF. Bias between 1.25 V and 6 V if unused; bypass to GND for noise immunity.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    4.445
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "DIS",
   "type": "input",
   "description": "Latched device shutdown. When the pin exceeds 1.85 V the IC is latched OFF at near-zero consumption; latch cleared only by recycling VCC below UVLO. Enables easy OTP/OVP implementation. Tie to GND if unused.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "9",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    4.445
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "9",
   "name": "PFC_STOP",
   "type": "output",
   "description": "Open-drain ON/OFF control for the upstream PFC controller. Pulled low when the IC is shut down (DIS>1.85V, ISEN>1.5V, LINE>6V, STBY<1.25V or DELAY>2V) and re-opens after DELAY falls below 0.3V. Open during UVLO. Leave unconnected if unused.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "10",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    3.175
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "10",
   "name": "GND",
   "type": "power_in",
   "description": "Chip signal/low-side driver ground. All bias-component grounds should return here on a dedicated track kept separate from any pulsed current return.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "11",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "11",
   "name": "LVG",
   "type": "output",
   "description": "Low-side gate-drive output for the half-bridge lower MOSFET. Capable of 0.3 A min source / 0.8 A min sink peak current; actively pulled to GND during UVLO.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "12",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "12",
   "name": "VCC",
   "type": "power_in",
   "description": "Supply voltage for the signal section and the low-side gate driver. Operating range 8.85-16 V, turn-ON ~10.7 V, turn-OFF ~8.15 V, VCC clamp ~17 V. A small (0.1 uF typ.) bypass to GND may be useful to keep clean bias for the signal section.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "13",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "13",
   "name": "N.C.",
   "type": "unconnected",
   "description": "High-voltage spacer. Not internally connected; isolates the high-voltage pins and eases PCB creepage/safety compliance.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "14",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "14",
   "name": "OUT",
   "type": "power_in",
   "description": "High-side gate-drive floating ground and current return for the high-side driver. Rated -3 V to VBOOT-18 V; connects to the half-bridge switching node. Route carefully to avoid large negative spikes.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "15",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -3.175
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "15",
   "name": "HVG",
   "type": "output",
   "description": "High-side floating gate-drive output for the half-bridge upper MOSFET. Capable of 0.3 A min source / 0.8 A min sink peak current. An internal resistor to OUT (pin 14) keeps the pin from floating during UVLO.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "16",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -4.445
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "16",
   "name": "VBOOT",
   "type": "power_in",
   "description": "High-side gate-drive floating supply. Bootstrap capacitor between VBOOT and OUT (pin 14) is refreshed by an internal synchronous bootstrap DMOS driven in phase with the low-side driver, replacing the external fast-recovery diode. Floating supply rated up to 618 V (max), tested to 580 V leakage.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-16_3.9x9.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}