← Commit history

Initial commit: component/l6563atr

Ray ·284a6db5bb ·
2 files changed +227
README.mdadded+50
@@ -0,0 +1,50 @@+# L6563ATR++**STMicroelectronics** · AC-DC Controllers And Regulators · SOIC-14++L6563ATR from STMicroelectronics, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | INV | input | Inverting input of error amplifier for output voltage feedback via resistor divider; input impedance high, can sink current from TBO pin during tracking boost operation. |+| 2 | COMP | output | Error amplifier output with frequency compensation network to INV pin; output clamp voltage 2.1 to 6.7V depending on input state. |+| 3 | MULT | input | Multiplier main input receiving rectified mains voltage reference via resistor divider; linear operation 0 to 3V with internal clamp at 9 to 9.5V. |+| 4 | CS | input | PWM comparator current sense input detecting MOSFET current through sense resistor; normal operation limit ~1.08V for turn-off comparison. |+| 5 | VFF | input | Voltage feedforward input for 1/V² compensation; connect external RC peak-holding network to ground; operating range 0.5 to 3V with 20mV dropout from MULT peak. |+| 6 | TBO | output | Tracking boost output providing buffered VFF voltage; external resistor to ground defines mains-tracking current sink from INV pin (maximum current 0.25mA). |+| 7 | PFC_OK | input | PFC output voltage monitor input for feedback failure protection; latch-off when exceeds 2.5V or auto-disable when below 0.2V with re-enable threshold 0.26V. |+| 8 | PWM_LATCH | tri_state | Open-source fault output asserted high (3.7V minimum) when PFC_OK exceeds 2.5V for feedback failure detection; signals cascaded DC-DC converter PWM controller with latched shutdown. |+| 9 | PWM_STOP | tri_state | Open-drain fault output pulled low (1V at 0.5mA sink) when RUN input disabled below 0.52V; signals temporary disable to cascaded DC-DC converter PWM controller. |+| 10 | RUN | input | Remote ON/OFF control input for brownout protection; disable threshold 0.5 to 0.54V, re-enable threshold 0.56 to 0.64V with hysteresis for non-latched shutdown. |+| 11 | ZCD | input | Zero-current detector input for boost inductor demagnetization sensing in transition-mode operation; negative-going edge triggers MOSFET turn-on. |+| 12 | GND | power_in | Ground; signal and power current return for IC logic and gate driver output stage. |+| 13 | GD | output | Gate driver output with 600mA source and 800mA sink peak current capability for driving power MOSFETs and IGBTs; output voltage clamped to approximately 12V. |+| 14 | VCC | power_in | Supply voltage for IC logic and gate driver stages; operating range 10.3 to 22V with turn-on at 11 to 13V, turn-off at 8.7 to 10.3V, and Zener clamp at 22 to 25V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | SOIC-14 |+| Category | Power Management (PMIC) |+| Pins | 14 |++## CAD (KiCad official)++- Symbol: `L6563ATR`+- Footprint: `Package_SO:SOIC-14_3.9x8.7mm_P1.27mm`+- 3D model: SOIC-14 (KiCad packages3D, STEP)+- 3D model files: `l6563atr-etched.step` / `l6563atr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `l6563atr.step` / `l6563atr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590918754861993984) (39 pp, sha256 `867a46c1733f77b9`, retrieved 2026-09-23, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/l6563atr-datasheet.pdf)
page.jsonadded+177
@@ -0,0 +1,177 @@+{+  "slug": "l6563atr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics AC-DC Controllers And Regulators, SOIC-14. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "l6563atr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "l6563atr.kicad_sym",+    "l6563atr.kicad_mod",+    "l6563atr.glb",+    "l6563atr.step",+    "l6563atr.lbr",+    "docs/hero.png",+    "docs/l6563atr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "L6563ATR",+    "manufacturer": "STMicroelectronics",+    "package": "SOIC-14",+    "pin_count": 14,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590918754861993984",+    "parts": {+      "symbol": "l6563atr.kicad_sym",+      "footprint": "l6563atr.kicad_mod",+      "model_3d": "l6563atr-etched.glb",+      "model_3d_plain": "l6563atr.glb",+      "model_3d_step": "l6563atr-etched.step",+      "model_3d_step_plain": "l6563atr.step",+      "lbr": "l6563atr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2970939"+    },+    "pins": [+      {+        "number": "1",+        "name": "INV",+        "type": "input",+        "description": "Inverting input of error amplifier for output voltage feedback via resistor divider; input impedance high, can sink current from TBO pin during tracking boost operation."+      },+      {+        "number": "2",+        "name": "COMP",+        "type": "output",+        "description": "Error amplifier output with frequency compensation network to INV pin; output clamp voltage 2.1 to 6.7V depending on input state."+      },+      {+        "number": "3",+        "name": "MULT",+        "type": "input",+        "description": "Multiplier main input receiving rectified mains voltage reference via resistor divider; linear operation 0 to 3V with internal clamp at 9 to 9.5V."+      },+      {+        "number": "4",+        "name": "CS",+        "type": "input",+        "description": "PWM comparator current sense input detecting MOSFET current through sense resistor; normal operation limit ~1.08V for turn-off comparison."+      },+      {+        "number": "5",+        "name": "VFF",+        "type": "input",+        "description": "Voltage feedforward input for 1/V² compensation; connect external RC peak-holding network to ground; operating range 0.5 to 3V with 20mV dropout from MULT peak."+      },+      {+        "number": "6",+        "name": "TBO",+        "type": "output",+        "description": "Tracking boost output providing buffered VFF voltage; external resistor to ground defines mains-tracking current sink from INV pin (maximum current 0.25mA)."+      },+      {+        "number": "7",+        "name": "PFC_OK",+        "type": "input",+        "description": "PFC output voltage monitor input for feedback failure protection; latch-off when exceeds 2.5V or auto-disable when below 0.2V with re-enable threshold 0.26V."+      },+      {+        "number": "8",+        "name": "PWM_LATCH",+        "type": "tri_state",+        "description": "Open-source fault output asserted high (3.7V minimum) when PFC_OK exceeds 2.5V for feedback failure detection; signals cascaded DC-DC converter PWM controller with latched shutdown."+      },+      {+        "number": "9",+        "name": "PWM_STOP",+        "type": "tri_state",+        "description": "Open-drain fault output pulled low (1V at 0.5mA sink) when RUN input disabled below 0.52V; signals temporary disable to cascaded DC-DC converter PWM controller."+      },+      {+        "number": "10",+        "name": "RUN",+        "type": "input",+        "description": "Remote ON/OFF control input for brownout protection; disable threshold 0.5 to 0.54V, re-enable threshold 0.56 to 0.64V with hysteresis for non-latched shutdown."+      },+      {+        "number": "11",+        "name": "ZCD",+        "type": "input",+        "description": "Zero-current detector input for boost inductor demagnetization sensing in transition-mode operation; negative-going edge triggers MOSFET turn-on."+      },+      {+        "number": "12",+        "name": "GND",+        "type": "power_in",+        "description": "Ground; signal and power current return for IC logic and gate driver output stage."+      },+      {+        "number": "13",+        "name": "GD",+        "type": "output",+        "description": "Gate driver output with 600mA source and 800mA sink peak current capability for driving power MOSFETs and IGBTs; output voltage clamped to approximately 12V."+      },+      {+        "number": "14",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage for IC logic and gate driver stages; operating range 10.3 to 22V with turn-on at 11 to 13V, turn-off at 8.7 to 10.3V, and Zener clamp at 22 to 25V."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 39,+        "cost_usd": 0.3919,+        "at": "2026-09-23T12:21:29"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590918754861993984",+        "pages": 39,+        "sha256": "867a46c1733f77b9",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 14,+        "described": 14,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file