component
KSZ9477STXI
Public Made by Adomby adom
Microchip Tech Pre-ordered MCUs, TQFP-128(14x14). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownKSZ9477STXI
Microchip Tech · Pre-ordered MCUs · TQFP-128(14x14)
KSZ9477STXI from Microchip Tech, in a TQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TXRX1P_A | passive | Port 1 1000BASE-T differential data pair A (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 2 | TXRX1M_A | passive | Port 1 1000BASE-T differential data pair A (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 3 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 4 | TXRX1P_B | passive | Port 1 1000BASE-T differential data pair B (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 5 | TXRX1M_B | passive | Port 1 1000BASE-T differential data pair B (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 6 | TXRX1P_C | passive | Port 1 1000BASE-T differential data pair C (+). |
| 7 | TXRX1M_C | passive | Port 1 1000BASE-T differential data pair C (-). |
| 8 | TXRX1P_D | passive | Port 1 1000BASE-T differential data pair D (+). |
| 9 | TXRX1M_D | passive | Port 1 1000BASE-T differential data pair D (-). |
| 10 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
| 11 | DVDDL | power_in | +1.2V digital core power. |
| 12 | TXRX2P_A | passive | Port 2 1000BASE-T differential data pair A (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 13 | TXRX2M_A | passive | Port 2 1000BASE-T differential data pair A (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 14 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 15 | TXRX2P_B | passive | Port 2 1000BASE-T differential data pair B (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 16 | TXRX2M_B | passive | Port 2 1000BASE-T differential data pair B (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 17 | TXRX2P_C | passive | Port 2 1000BASE-T differential data pair C (+). |
| 18 | TXRX2M_C | passive | Port 2 1000BASE-T differential data pair C (-). |
| 19 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 20 | TXRX2P_D | passive | Port 2 1000BASE-T differential data pair D (+). |
| 21 | TXRX2M_D | passive | Port 2 1000BASE-T differential data pair D (-). |
| 22 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
| 23 | DVDDL | power_in | +1.2V digital core power. |
| 24 | TXRX3P_A | passive | Port 3 1000BASE-T differential data pair A (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 25 | TXRX3M_A | passive | Port 3 1000BASE-T differential data pair A (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 26 | TXRX3P_B | passive | Port 3 1000BASE-T differential data pair B (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 27 | TXRX3M_B | passive | Port 3 1000BASE-T differential data pair B (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 28 | TXRX3P_C | passive | Port 3 1000BASE-T differential data pair C (+). |
| 29 | TXRX3M_C | passive | Port 3 1000BASE-T differential data pair C (-). |
| 30 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 31 | TXRX3P_D | passive | Port 3 1000BASE-T differential data pair D (+). |
| 32 | TXRX3M_D | passive | Port 3 1000BASE-T differential data pair D (-). |
| 33 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
| 34 | TXRX4P_A | passive | Port 4 1000BASE-T differential data pair A (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 35 | TXRX4M_A | passive | Port 4 1000BASE-T differential data pair A (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 36 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 37 | TXRX4P_B | passive | Port 4 1000BASE-T differential data pair B (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 38 | TXRX4M_B | passive | Port 4 1000BASE-T differential data pair B (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 39 | TXRX4P_C | passive | Port 4 1000BASE-T differential data pair C (+). |
| 40 | TXRX4M_C | passive | Port 4 1000BASE-T differential data pair C (-). |
| 41 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 42 | TXRX4P_D | passive | Port 4 1000BASE-T differential data pair D (+). |
| 43 | TXRX4M_D | passive | Port 4 1000BASE-T differential data pair D (-). |
| 44 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
| 45 | DVDDL | power_in | +1.2V digital core power. |
| 46 | GND | power_in | Ground (pins and exposed pad). |
| 47 | GND | power_in | Ground (pins and exposed pad). |
| 48 | TX_CLK6/REFCLKI6 | bidirectional | Port 6 transmit clock: 25/2.5MHz output in MII PHY mode or input in MAC mode, 50MHz RMII reference clock input in RMII normal mode, and 125/25/2.5MHz clock input in RGMII mode. |
| 49 | TX_EN6/TX_CTL6 | input | Port 6 transmit enable in MII/RMII modes or transmit control in RGMII mode. |
| 50 | TX_ER6 | input | Port 6 MII transmit error input; not used in RMII or RGMII and should not be connected in those modes. |
| 51 | COL6 | bidirectional | Port 6 MII collision detect (output in PHY mode, input in MAC mode); not used in RMII/RGMII and should not be connected in those modes. |
| 52 | TXD6_3 | input | Port 6 MII/RGMII transmit data bit 3; not used in RMII mode and should not be connected in that mode. |
| 53 | TXD6_2 | input | Port 6 MII/RGMII transmit data bit 2; not used in RMII mode and should not be connected in that mode. |
| 54 | TXD6_1 | input | Port 6 transmit data bit 1 for MII, RMII, and RGMII modes. |
| 55 | TXD6_0 | input | Port 6 transmit data bit 0 for MII, RMII, and RGMII modes. |
| 56 | DVDDL | power_in | +1.2V digital core power. |
| 57 | RX_CLK6/REFCLKO6 | bidirectional | Port 6 MII receive clock (25/2.5MHz); 50MHz RMII reference clock output in RMII clock mode; 125/25/2.5MHz RGMII receive clock output. |
| 58 | RX_DV6/CRS_DV6/RX_CTL6 | output | Port 6 MII receive data valid output, RMII carrier sense/receive data valid output, or RGMII receive control output. |
| 59 | RX_ER6 | output | Port 6 MII receive error output; not used in RMII or RGMII and should not be connected in those modes. |
| 60 | CRS6 | bidirectional | Port 6 MII carrier sense (output in PHY mode, input in MAC mode); not used in RMII/RGMII and should not be connected in those modes. |
| 61 | VDDIO | power_in | +3.3V / +2.5V / +1.8V I/O power. |
| 62 | RXD6_3 | output | Port 6 MII/RGMII receive data bit 3, also a configuration strap sampled at reset (Port 6 mode select); not used in RMII mode. |
| 63 | RXD6_2 | output | Port 6 MII/RGMII receive data bit 2, also a configuration strap sampled at reset (Port 6 mode select); not used in RMII mode. |
| 64 | RXD6_1 | output | Port 6 receive data bit 1 for MII/RMII/RGMII modes, also a configuration strap sampled at reset (Port 6 MII/RMII mode select). |
| 65 | RXD6_0 | output | Port 6 receive data bit 0 for MII/RMII/RGMII modes, also a configuration strap sampled at reset (Port 6 speed select, 1000 or 100 Mbps). |
| 66 | DVDDL | power_in | +1.2V digital core power. |
| 67 | IBA | input | In-band management configuration strap sampled at reset (0 = disabled, default; 1 = enabled). |
| 68 | VDDIO | power_in | +3.3V / +2.5V / +1.8V I/O power. |
| 69 | GND | power_in | Ground (pins and exposed pad). |
| 70 | DVDDL | power_in | +1.2V digital core power. |
| 71 | VDDLS | power_in | +1.2V SGMII core power. |
| 72 | VDDHS | power_in | +2.5V SGMII I/O power. |
| 73 | NC | unconnected | No connect; must be left unconnected for proper operation. |
| 74 | NC | unconnected | No connect; must be left unconnected for proper operation. |
| 75 | GND | power_in | Ground (pins and exposed pad). |
| 76 | S_REXT | passive | SGMII reference resistor; connect a 191Ω 1% resistor between this pin and GND using a short trace. |
| 77 | GND | power_in | Ground (pins and exposed pad). |
| 78 | S_IN7M | input | Port 7 SGMII differential input data (-). |
| 79 | S_IN7P | input | Port 7 SGMII differential input data (+). |
| 80 | GND | power_in | Ground (pins and exposed pad). |
| 81 | S_OUT7P | output | Port 7 SGMII differential output data (+). |
| 82 | S_OUT7M | output | Port 7 SGMII differential output data (-). |
| 83 | VDDHS | power_in | +2.5V SGMII I/O power. |
| 84 | VDDLS | power_in | +1.2V SGMII core power. |
| 85 | LED4_0 | bidirectional | Port 4 LED indicator 0, active-low sink to light an external LED; also a configuration strap sampled at reset. |
| 86 | LED4_1 | bidirectional | Port 4 LED indicator 1, active-low sink to light an external LED; also a configuration strap sampled at reset. |
| 87 | DVDDL | power_in | +1.2V digital core power. |
| 88 | LED3_0 | bidirectional | Port 3 LED indicator 0, active-low output that sinks current to light an external LED. |
| 89 | LED3_1 | bidirectional | Port 3 LED indicator 1, active-low output that sinks current to light an external LED; also a configuration strap sampled at reset. |
| 90 | GPIO_1 | bidirectional | General purpose I/O 1 for IEEE 1588 event trigger or timestamp capture, synchronized to the internal IEEE 1588 clock. |
| 91 | LED2_0 | bidirectional | Port 2 LED indicator 0, active-low output that sinks current to light an external LED; also a configuration strap sampled at reset. |
| 92 | LED2_1 | bidirectional | Port 2 LED indicator 1, active-low output that sinks current to light an external LED; also a configuration strap sampled at reset. |
| 93 | PME_N | output | Power management event output indicating an energy detect event; polarity is programmable (default active low) and requires an external pull-up for active-low operation. |
| 94 | INTRP_N | output | Active-low open-drain interrupt output that requires an external pull-up resistor; also a configuration strap sampled at reset. |
| 95 | SYNCLKO | bidirectional | 25/125MHz reference clock output derived from the crystal input or a PHY recovered clock, for Synchronous Ethernet; also a configuration strap that must be strapped high for SGMII operation. |
| 96 | RESET_N | input | Active-low system reset; the device must be reset during or after power-on, and an RC circuit is suggested for power-on reset. |
| 97 | SDO | output | SPI data out (MISO) in SPI mode; not used in I2C or MIIM modes. |
| 98 | SDI/SDA/MDIO | bidirectional | SPI data in (MOSI), I2C data, or MIIM MDIO; open-drain when driven and requires a 1.0kΩ to 4.7kΩ pull-up to VDDIO. |
| 99 | VDDIO | power_in | +3.3V / +2.5V / +1.8V I/O power. |
| 100 | SCS_N | input | SPI chip select, active low; not used in I2C or MIIM modes. |
| 101 | SCL/MDC | input | SPI/I2C serial clock, or MIIM MDC serial clock. |
| 102 | LED5_0 | bidirectional | Port 5 LED indicator 0, active-low output that sinks current to light an external LED. |
| 103 | LED5_1 | bidirectional | Port 5 LED indicator 1, active-low output that sinks current to light an external LED; also a configuration strap sampled at reset. |
| 104 | DVDDL | power_in | +1.2V digital core power. |
| 105 | LED1_0 | bidirectional | Port 1 LED indicator 0, active-low output that sinks current to light an external LED; also a configuration strap (Quiet-WIRE filtering enable) sampled at reset. |
| 106 | LED1_1 | bidirectional | Port 1 LED indicator 1, active-low output that sinks current to light an external LED; also a configuration strap (flow control enable) sampled at reset. |
| 107 | GND | power_in | Ground (pins and exposed pad). |
| 108 | NC | unconnected | No connect; must be left unconnected for proper operation. |
| 109 | GND | power_in | Ground (pins and exposed pad). |
| 110 | DVDDL | power_in | +1.2V digital core power. |
| 111 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
| 112 | TXRX5P_A | passive | Port 5 1000BASE-T differential data pair A (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 113 | TXRX5M_A | passive | Port 5 1000BASE-T differential data pair A (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 114 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 115 | TXRX5P_B | passive | Port 5 1000BASE-T differential data pair B (+), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 116 | TXRX5M_B | passive | Port 5 1000BASE-T differential data pair B (-), also used for 100BASE-TX and 10BASE-Te on the A and B pairs. |
| 117 | TXRX5P_C | passive | Port 5 1000BASE-T differential data pair C (+). |
| 118 | TXRX5M_C | passive | Port 5 1000BASE-T differential data pair C (-). |
| 119 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 120 | TXRX5P_D | passive | Port 5 1000BASE-T differential data pair D (+). |
| 121 | TXRX5M_D | passive | Port 5 1000BASE-T differential data pair D (-). |
| 122 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
| 123 | GND | power_in | Ground (pins and exposed pad). |
| 124 | AVDDL | power_in | +1.2V analog power for the PHY core. |
| 125 | XO | output | Crystal clock output; connect to one lead of a 25MHz crystal, or leave unconnected when an oscillator drives XI. |
| 126 | XI | input | Crystal clock/oscillator input; 25MHz crystal lead or external oscillator input, with crystal tolerance of ±50ppm. |
| 127 | ISET | passive | Transmit output current set resistor; must be connected to GND through a 6.04kΩ 1% resistor. |
| 128 | AVDDH | power_in | +2.5V analog power for the PHY transceivers and XI/XO interface. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TQFP-128(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 128 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (AVDDL, DVDDL, VDDLS) | AVDDL, DVDDL, VDDLS | 1.14 | 1.26 | V | 235 | ||
| Supply Voltage (AVDDH, VDDHS) | AVDDH, VDDHS | 2.375 | 2.625 | V | 235 | ||
| Supply Voltage (VDDIO @ 3.3V) | VDDIO | 3.135 | 3.465 | V | @ 3.3V | 235 | |
| Supply Voltage (VDDIO @ 2.5V) | VDDIO | 2.375 | 2.625 | V | @ 2.5V | 235 | |
| Supply Voltage (VDDIO @ 1.8V) | VDDIO | 1.71 | 1.89 | V | @ 1.8V | 235 | |
| Ambient Operating Temperature in Still Air | TA | -40 | 85 | °C | Industrial version (Note 6-1) | 235 | |
| Supply Voltage (AVDDL, DVDDL, VDDLS) | AVDDL, DVDDL, VDDLS | -0.5 | 1.8 | V | 235 | ||
| Supply Voltage (AVDDH, VDDIO, VDDHS) | AVDDH, VDDIO, VDDHS | -0.5 | 5 | V | 235 | ||
| Input Voltage (all inputs) | -0.5 | 5 | V | 235 | |||
| Output Voltage (all outputs) | -0.5 | 5 | V | 235 | |||
| Lead Temperature (soldering) | 260 | °C | 20 sec. | 235 | |||
| Storage Temperature | TS | -65 | 150 | °C | 235 | ||
| Maximum Junction Temperature | TJ | 125 | °C | 235 | |||
| HBM ESD Performance | -6 | 6 | kV | HBM | 235 | ||
| AVDDH supply current (Full 1000 Mbps) | IDD_AH | 330 | mA | VDDIO @3.3V; Ports 1-5 in 1000BASE-T; Ports 6 & 7 @ 1000 Mbps; All ports 100% utilization | 236 | ||
| VDDIO supply current (Full 1000 Mbps) | IDD_IO | 45 | mA | 236 | |||
| AVDDL supply current (Full 1000 Mbps) | IDD_CA | 460 | mA | 236 | |||
| DVDDL supply current (Full 1000 Mbps) | IDD_CD | 750 | mA | 236 | |||
| VDDHS supply current (Full 1000 Mbps) | IDD_HS | 20 | mA | 236 | |||
| VDDLS supply current (Full 1000 Mbps) | IDD_LS | 15 | mA | 236 | |||
| AVDDH supply current (Energy Detect Mode) | IDD_AH | 20 | mA | 237 | |||
| VDDIO supply current (Energy Detect Mode) | IDD_IO | 30 | mA | (3.3V) | 237 | ||
| AVDDL supply current (Energy Detect Mode) | IDD_CA | 30 | mA | 237 | |||
| DVDDL supply current (Energy Detect Mode) | IDD_CD | 150 | mA | 237 | |||
| VDDHS supply current (Energy Detect Mode) | IDD_HS | 20 | mA | 237 | |||
| VDDLS supply current (Energy Detect Mode) | IDD_LS | 15 | mA | 237 | |||
| AVDDH supply current (Global Soft Power Down) | IDD_AH | 2 | mA | 237 | |||
| VDDIO supply current (Global Soft Power Down) | IDD_IO | 6 | mA | (3.3V) | 237 | ||
| AVDDL supply current (Global Soft Power Down) | IDD_CA | 0.01 | mA | 237 | |||
| DVDDL supply current (Global Soft Power Down) | IDD_CD | 5 | mA | 237 | |||
| VDDHS supply current (Global Soft Power Down) | IDD_HS | 20 | mA | 237 | |||
| VDDLS supply current (Global Soft Power Down) | IDD_LS | 15 | mA | 237 | |||
| Input High Voltage (CMOS input) | VIH | 2.1 | V | VDDIO = 3.3V | 237 | ||
| Input High Voltage (CMOS input) | VIH | 1.7 | V | VDDIO = 2.5V | 237 | ||
| Input High Voltage (CMOS input) | VIH | 1.3 | V | VDDIO = 1.8V | 237 | ||
| Input Low Voltage (CMOS input) | VIL | 0.9 | V | VDDIO = 3.3V | 237 | ||
| Input Low Voltage (CMOS input) | VIL | 0.6 | V | VDDIO = 1.8V | 237 | ||
| Input Current (CMOS input) | IIN | -10 | 10 | µA | VIN = GND ~ VDDIO | 237 | |
| Output High Voltage (O8) | VOH | 2.4 | V | VDDIO = 3.3V; IOH = 8 mA | 237 | ||
| Output High Voltage (O8) | VOH | 1.9 | V | VDDIO = 2.5V; IOH = 8 mA | 237 | ||
| Output High Voltage (O8) | VOH | 1.5 | V | VDDIO = 1.8V; IOH = 6 mA | 237 | ||
| Output Low Voltage (O8) | VOL | 0.4 | V | VDDIO = 3.3V; IOL = 8 mA | 237 | ||
| Output Low Voltage (O8) | VOL | 0.2 | V | VDDIO = 1.8V; IOL = 6 mA | 237 | ||
| Output Tri-State Leakage (O8) | IOZ | 10 | µA | VIN = GND ~ VDDIO | 237 | ||
| Minimum RX Eye Height (differential peak-to-peak) | VRXEYE | 175 | mV | 237 | |||
| Differential Input Impedance | ZIN | 85 | 115 | Ω | 237 | ||
| PPM Tolerance | PPM | -350 | 350 | ppm | 237 | ||
| Driver Output Voltage (peak-to-peak, differential amplitude) | VDIFF | 0.8 | 1.2 | V | 238 | ||
| Transmit Common Mode Voltage | VCTM | 0.4 | 0.6 | V | 238 | ||
| Driver Differential Output Impedance | ZD | 85 | 115 | Ω | 238 | ||
| Peak Differential Output (100BASE-TX) | VO | 0.95 | 1.05 | V | 100Ω termination on the differential output | 238 | |
| Rise/Fall Time (100BASE-TX) | tr, tf | 3 | 5 | ns | 238 | ||
| Peak Differential Output Voltage (10BASE-Te) | Vp | 1.54 | 1.75 | 1.96 | V | 100Ω termination on the differential output | 238 |
| Junction to Ambient Resistance | JA | 11.3 | °C/W | 6-layer PCB per JESD51; 0 m/s (Note 6-3) | 235 | ||
| Junction to Ambient Resistance | JA | 14.4 | °C/W | 4-layer PCB per JESD51 (Note 6-3) | 235 | ||
| Junction to Case Characterization | JT | 0.04 | °C/W | 0 m/s air velocity (Note 6-2) | 235 | ||
| Junction to Case Resistance | JC | 1.5 | °C/W | 6-layer PCB per JESD51 (Note 6-4) | 235 | ||
| Junction to Case Resistance | JC | 1.21 | °C/W | 4-layer PCB per JESD51 (Note 6-4) | 235 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | abs | Quiet-WIRE is a feature to enhance 100BASE-TX EMC performance by reducing both conducted and radiated emissions from the TXP/M signal pair. It can be used either to reduce absolute emissions, or to e | 24 |
CAD (KiCad official)
- Symbol:
KSZ9477STXI - Footprint:
Package_QFP:TQFP-128_14x14mm_P0.4mm - 3D model: TQFP-128(14x14) (KiCad packages3D, STEP)
- 3D model files:
ksz9477stxi-etched.step/ksz9477stxi-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz9477stxi.step/ksz9477stxi.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (266 pp, sha256
73deb606faa230e8, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).