3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownKSZ9031MNXIC
Microchip Tech · Pre-ordered MCUs · QFN-64-EP(8x8)
KSZ9031MNXIC from Microchip Tech, in a QFN-64-EP(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVDDH | power_in | 3.3V/2.5V (2.5V commercial temperature only) analog VDD. |
| 2 | TXRXP_A | bidirectional | Media Dependent Interface[0] positive differential signal (BI_DA+ for MDI, BI_DB+ for MDI-X in 1000BASE-T; TX+/RX+ in 10/100). |
| 3 | TXRXM_A | bidirectional | Media Dependent Interface[0] negative differential signal (BI_DA- for MDI, BI_DB- for MDI-X in 1000BASE-T; TX-/RX- in 10/100). |
| 4 | AVDDL | power_in | 1.2V analog VDD. |
| 5 | AVDDL | power_in | 1.2V analog VDD. |
| 6 | NC | unconnected | No connect. |
| 7 | TXRXP_B | bidirectional | Media Dependent Interface[1] positive differential signal (BI_DB+ for MDI, BI_DA+ for MDI-X in 1000BASE-T; RX+/TX+ in 10/100). |
| 8 | TXRXM_B | bidirectional | Media Dependent Interface[1] negative differential signal (BI_DB- for MDI, BI_DA- for MDI-X in 1000BASE-T; RX-/TX- in 10/100). |
| 9 | AGNDH | power_in | Analog ground. |
| 10 | TXRXP_C | bidirectional | Media Dependent Interface[2] positive differential signal (BI_DC+ for MDI, BI_DD+ for MDI-X in 1000BASE-T; not used in 10/100). |
| 11 | TXRXM_C | bidirectional | Media Dependent Interface[2] negative differential signal (BI_DC- for MDI, BI_DD- for MDI-X in 1000BASE-T; not used in 10/100). |
| 12 | AVDDL | power_in | 1.2V analog VDD. |
| 13 | AVDDL | power_in | 1.2V analog VDD. |
| 14 | TXRXP_D | bidirectional | Media Dependent Interface[3] positive differential signal (BI_DD+ for MDI, BI_DC+ for MDI-X in 1000BASE-T; not used in 10/100). |
| 15 | TXRXM_D | bidirectional | Media Dependent Interface[3] negative differential signal (BI_DD- for MDI, BI_DC- for MDI-X in 1000BASE-T; not used in 10/100). |
| 16 | AVDDH | power_in | 3.3V/2.5V (2.5V commercial temperature only) analog VDD. |
| 17 | LED2/PHYAD1 | bidirectional | Programmable LED2 output (link status in single-LED mode) that also latches PHYAD[1] strap at power-up/reset. |
| 18 | DVDDH | power_in | 3.3V, 2.5V, or 1.8V digital VDD_IO. |
| 19 | LED1/PHYAD0/PME_N1 | bidirectional | Programmable LED1 output, PHYAD[0] strap at power-up/reset, or PME_N output (pin option 1) needing a 1.0 kΩ to 4.7 kΩ pull-up to DVDDH. |
| 20 | DVDDL | power_in | 1.2V digital VDD. |
| 21 | TXD0 | input | GMII/MII transmit data 0 input. |
| 22 | TXD1 | input | GMII/MII transmit data 1 input. |
| 23 | TXD2 | input | GMII/MII transmit data 2 input. |
| 24 | TXD3 | input | GMII/MII transmit data 3 input. |
| 25 | DVDDL | power_in | 1.2V digital VDD. |
| 26 | TXD4 | input | GMII transmit data 4 input; not used in MII mode and can be driven high or low. |
| 27 | TXD5 | input | GMII transmit data 5 input; not used in MII mode and can be driven high or low. |
| 28 | TXD6 | input | GMII transmit data 6 input; not used in MII mode and can be driven high or low. |
| 29 | TXD7 | input | GMII transmit data 7 input; not used in MII mode and can be driven high or low. |
| 30 | DVDDH | power_in | 3.3V, 2.5V, or 1.8V digital VDD_IO. |
| 31 | TX_ER | input | GMII/MII transmit error input; tie low if the MAC does not provide TX_ER. |
| 32 | GTX_CLK | input | GMII transmit reference clock input (125 MHz for 1000 Mbps). |
| 33 | TX_EN | input | GMII/MII transmit enable input. |
| 34 | RXD7 | output | GMII receive data 7 output; driven low in MII mode. |
| 35 | RXD6 | output | GMII receive data 6 output; driven low in MII mode. |
| 36 | DVDDL | power_in | 1.2V digital VDD. |
| 37 | RXD5 | output | GMII receive data 5 output; driven low in MII mode. |
| 38 | RXD4 | output | GMII receive data 4 output; driven low in MII mode. |
| 39 | RXD3/MODE3 | bidirectional | GMII/MII receive data 3 output; latches MODE3 strap at power-up/reset. |
| 40 | DVDDH | power_in | 3.3V, 2.5V, or 1.8V digital VDD_IO. |
| 41 | RXD2/MODE2 | bidirectional | GMII/MII receive data 2 output; latches MODE2 strap at power-up/reset. |
| 42 | DVDDL | power_in | 1.2V digital VDD. |
| 43 | RXD1/MODE1 | bidirectional | GMII/MII receive data 1 output; latches MODE1 strap at power-up/reset. |
| 44 | RXD0/MODE0 | bidirectional | GMII/MII receive data 0 output; latches MODE0 strap at power-up/reset. |
| 45 | RX_DV/CLK125_EN | bidirectional | GMII/MII receive data valid output; latches CLK125_EN strap (pull-up enables 125 MHz clock output) at power-up/reset. |
| 46 | DVDDH | power_in | 3.3V, 2.5V, or 1.8V digital VDD_IO. |
| 47 | RX_ER | output | GMII/MII receive error output. |
| 48 | RX_CLK/PHYAD2 | bidirectional | GMII/MII receive reference clock output; latches PHYAD[2] strap at power-up/reset. |
| 49 | CRS | output | GMII/MII carrier sense output. |
| 50 | MDC | input | Management data clock input (internal pull-up), reference clock for MDIO. |
| 51 | MDIO | bidirectional | Management data input/output synchronous to MDC; requires 1.0 kΩ to 4.7 kΩ external pull-up to DVDDH. |
| 52 | COL | output | GMII/MII collision detected output. |
| 53 | INT_N/PME_N2 | output | Programmable interrupt output or PME_N output (pin option 2); needs 1.0 kΩ to 4.7 kΩ pull-up to DVDDH. |
| 54 | DVDDL | power_in | 1.2V digital VDD. |
| 55 | CLK125_NDO/LED_MODE | bidirectional | 125 MHz reference clock output for the MAC; latches LED_MODE strap at power-up/reset (pull-up single-LED, pull-down tri-color dual-LED). |
| 56 | RESET_N | input | Active-low chip reset with internal pull-up; hardware strap-ins are latched at its rising edge. |
| 57 | TX_CLK | output | MII transmit reference clock output. |
| 58 | LDO_O | output | On-chip 1.2V LDO controller output driving the gate of a P-channel MOSFET; leave floating if unused and never drive externally. |
| 59 | AVDDL_PLL | power_in | 1.2V analog VDD for PLL. |
| 60 | XO | output | 25 MHz crystal feedback; no connect if an oscillator or external clock is used. |
| 61 | XI | input | 25 MHz crystal, oscillator or external clock input, ±50 ppm tolerance. |
| 62 | NC | unconnected | No connect, not bonded; can be connected to AVDDH for footprint compatibility with KSZ9021GN. |
| 63 | ISET | passive | Sets transmit output level; connect a 12.1 kΩ 1% resistor to ground. |
| 64 | AGNDH | power_in | Analog ground. |
| 65 | P_GND | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-64-EP(8x8) |
| Category | Embedded Processors & Controllers |
| Pins | 65 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage core (abs max) | VIN | -0.5 | 1.8 | V | DVDDL, AVDDL, AVDDL_PLL | 49 | |
| Supply Voltage AVDDH (abs max) | VIN | -0.5 | 5 | V | AVDDH | 49 | |
| Supply Voltage DVDDH (abs max) | VIN | -0.5 | 5 | V | DVDDH | 49 | |
| Input Voltage | -0.5 | 5 | V | all inputs | 49 | ||
| Output Voltage | -0.5 | 5 | V | all outputs | 49 | ||
| Lead Temperature | 260 | °C | soldering, 10s | 49 | |||
| Storage Temperature | TS | -55 | 150 | °C | 49 | ||
| Core Supply Voltage | DVDDL, AVDDL, AVDDL_PLL | 1.14 | 1.38 | V | 49 | ||
| AVDDH Supply Voltage | AVDDH | 3.135 | 3.465 | V | AVDDH @ 3.3V | 49 | |
| DVDDH Supply Voltage 3.3V | DVDDH | 3.135 | 3.465 | V | DVDDH @ 3.3V | 49 | |
| DVDDH Supply Voltage 2.5V | DVDDH | 2.375 | 2.625 | V | DVDDH @ 2.5V | 49 | |
| DVDDH Supply Voltage 1.8V | DVDDH | 1.71 | 1.89 | V | DVDDH @ 1.8V | 49 | |
| Ambient Temperature (Industrial) | TA | -40 | 85 | °C | Industrial: KSZ9031MNXI | 49 | |
| Maximum Junction Temperature | TJ max. | 125 | °C | 49 | |||
| Thermal Resistance junction-to-ambient | ΘJA | 32.27 | °C/W | 49 | |||
| Thermal Resistance junction-to-case | ΘJC | 6.76 | °C/W | 49 | |||
| 1.2V core supply current | ICORE | 211 | mA | 1000Base-T link-up (no traffic) | 50 | ||
| 1.2V core supply current | ICORE | 221 | mA | 1000Base-T full-duplex @ 100% utilization | 50 | ||
| 1.2V core supply current | ICORE | 0.8 | mA | Chip power-down mode (strap-in pins MODE[3:0] = 0111) | 50 | ||
| 3.3V digital I/O supply current | IDVDDH_3.3 | 26 | mA | 1000Base-T link-up (no traffic) | 51 | ||
| 3.3V digital I/O supply current | IDVDDH_3.3 | 53.8 | mA | 1000Base-T full-duplex @ 100% utilization | 51 | ||
| 3.3V transceiver supply current | IAVDDH_3.3 | 66.6 | mA | 1000Base-T link-up (no traffic) | 51 | ||
| 3.3V transceiver supply current | IAVDDH_3.3 | 65.6 | mA | 1000Base-T full-duplex @ 100% utilization | 51 | ||
| 3.3V transceiver supply current | IAVDDH_3.3 | 0.02 | mA | Chip power-down mode (strap-in pins MODE[3:0] = 0111) | 51 |
CAD (KiCad official)
- Symbol:
KSZ9031MNXIC - Footprint:
Package_DFN_QFN:QFN-64-1EP_8x8mm_P0.4mm_EP6.5x6.5mm - 3D model: QFN-64-EP(8x8) (KiCad packages3D, STEP)
- 3D model files:
ksz9031mnxic-etched.step/ksz9031mnxic-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz9031mnxic.step/ksz9031mnxic.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (74 pp, sha256
370ef8e434a54881, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).