Generated by kicad-footprint-generator · KiCad file format 20260206
KSZ8873MMLI
Microchip Tech · Pre-ordered MCUs · LQFP-64(10x10)
KSZ8873MMLI from Microchip Tech, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RXM1 | bidirectional | Port 1 physical receive or transmit signal (- differential). |
| 2 | RXP1 | bidirectional | Port 1 physical receive or transmit signal (+ differential). |
| 3 | AGND | power_in | Analog ground. |
| 4 | TXM1 | bidirectional | Port 1 physical transmit or receive signal (- differential). |
| 5 | TXP1 | bidirectional | Port 1 physical transmit or receive signal (+ differential). |
| 6 | VDDA_3.3 | power_in | 3.3V analog VDD. |
| 7 | AGND | power_in | Analog ground. |
| 8 | ISET | output | Sets physical transmit output current; pull down with an 11.8kΩ 1% resistor to ground. |
| 9 | VDDA_1.8 | power_in | 1.8V analog core power input from VDDCO (pin 56). |
| 10 | RXM2 | bidirectional | Port 2 physical receive or transmit signal (- differential). |
| 11 | RXP2 | bidirectional | Port 2 physical receive or transmit signal (+ differential). |
| 12 | AGND | power_in | Analog ground. |
| 13 | TXM2 | bidirectional | Port 2 physical transmit or receive signal (- differential). |
| 14 | TXP2 | bidirectional | Port 2 physical transmit or receive signal (+ differential). |
| 15 | FXSD2 | input | On MLL/RLL, connect to analog ground by a pull-down resistor (fiber signal detect on FLL). |
| 16 | PWRDN | input | Chip power-down input, active-low, with internal pull-up. |
| 17 | X1 | input | 25 MHz or 50 MHz crystal/oscillator connection (±50 ppm); an oscillator, 3.3V tolerant, connects to X1 and must be applied before reset goes high. |
| 18 | X2 | output | Crystal connection; no connect when an oscillator drives X1. |
| 19 | SMTXEN3 | input | Switch MII transmit enable, with internal pull-up. |
| 20 | SMTXD33 | input | Switch MII transmit data bit 3 (MLL/FLL), with internal pull-up. |
| 21 | SMTXD32 | input | Switch MII transmit data bit 2 (MLL/FLL), with internal pull-up. |
| 22 | SMTXD31 | input | Switch MII/RMII transmit data bit 1, with internal pull-up. |
| 23 | SMTXD30 | input | Switch MII/RMII transmit data bit 0, with internal pull-up. |
| 24 | GND | power_in | Digital ground. |
| 25 | VDDIO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO, with well decoupling capacitors. |
| 26 | SMTXC3 | bidirectional | Switch MII transmit clock (MLL/FLL): output in PHY MII mode and SNI mode, input in MAC MII mode. |
| 27 | SMTXER3 | input | Switch MII transmit error; as MII_LINK_3 in PHY mode, 0 = link from host, 1 = no link on port 3 and enables bypass mode; internal pull-down. |
| 28 | SMRXDV3 | bidirectional | Switch MII receive data valid; strap selects MII mode: pull-up = PHY mode, pull-down = MAC mode. |
| 29 | SMRXD33 | bidirectional | Switch MII receive data bit 3; strap enables auto-negotiation on port 2 (P2ANEN): pull-up = enable, pull-down = disable. |
| 30 | SMRXD32 | bidirectional | Switch MII receive data bit 2; strap forces port 2 speed if P2ANEN = 0: pull-up = 100BT, pull-down = 10BT. |
| 31 | SMRXD31 | bidirectional | Switch MII receive data bit 1; strap sets port 2 duplex (P2DPX): pull-up = full-duplex, pull-down = half-duplex. |
| 32 | GND | power_in | Digital ground. |
| 33 | SMRXD30 | bidirectional | Switch MII receive data bit 0; strap forces port 2 flow control (P2FFC): pull-up = always enabled, pull-down = by auto-negotiation result. |
| 34 | SCRS3 | bidirectional | Switch MII carrier sense (MLL/FLL); in MAC mode drive from PHY CRS or (TXEN |
| 35 | SCOL3 | bidirectional | Switch MII collision detect (MLL/FLL), with internal pull-up. |
| 36 | SMRXC3 | bidirectional | Switch MII receive clock (MLL/FLL): output in PHY MII mode, input in MAC MII mode. |
| 37 | GND | power_in | Digital ground. |
| 38 | VDDC | power_in | 1.8V digital core power input from VDDCO (pin 56). |
| 39 | SPIQ | bidirectional | SPI slave serial data output (external pull-up needed when in use); strap selects XCLK frequency: pull-up = 25 MHz, pull-down = 50 MHz. |
| 40 | SPISN | input | SPI slave chip select, active-low; high deselects the device and tri-states SPIQ; external pull-up needed when in use. |
| 41 | INTRN | output | Active-low interrupt to host CPU indicating an interrupt status bit is set on lost link (registers 187 and 188), with internal pull-up. |
| 42 | SCL_MDC | bidirectional | Clock: input in SPI slave/I2C slave/MIIM modes, output in I2C master mode. |
| 43 | SDA_MDIO | bidirectional | SPI serial data input, I2C serial data I/O, or MIIM data I/O; external pull-up needed when in use. |
| 44 | NC | unconnected | Unused pin; only this NC pin may be pulled down by a resistor for better EMI. |
| 45 | P1ANEN | bidirectional | Strap: pull-up enables, pull-down disables auto-negotiation on port 1. |
| 46 | P1SPD | bidirectional | Strap: if P1ANEN = 0, pull-up forces port 1 to 100BT, pull-down forces 10BT. |
| 47 | P1DPX | bidirectional | Strap: pull-up sets port 1 full-duplex, pull-down sets half-duplex (default or forced depending on P1ANEN). |
| 48 | GND | power_in | Digital ground. |
| 49 | VDDC | power_in | 1.8V digital core power input from VDDCO (pin 56). |
| 50 | P1FFC | bidirectional | Strap: pull-up always forces port 1 flow control, pull-down leaves it to the auto-negotiation result. |
| 51 | P3SPD | bidirectional | Strap: pull-up forces port 3 to 10BT, pull-down forces 100BT (default); internal pull-down. |
| 52 | NC | unconnected | Unused pin; no external connection. |
| 53 | NC | unconnected | Unused pin; no external connection. |
| 54 | VDDIO | power_in | 3.3V, 2.5V or 1.8V digital VDD input for IO, with well decoupling capacitors. |
| 55 | GND | power_in | Digital ground. |
| 56 | VDDCO | power_out | 1.8V internal LDO output (input from VDDIO) powering VDDA_1.8 and VDDC; do not connect an external supply, use a ferrite bead between analog and digital 1.8V. |
| 57 | NC | unconnected | Unused pin; no external connection. |
| 58 | P1LED1 | bidirectional | Port 1 LED (default speed, register 195 bits[5:4]); strap selects port 3 flow control: pull-up = always enabled (default), pull-down = disabled. |
| 59 | P1LED0 | bidirectional | Port 1 LED (default link/activity); strap selects port 3 duplex: pull-up = half, pull-down = full (default); external 0.5kΩ pull-down recommended. |
| 60 | P2LED1 | bidirectional | Port 2 LED; with P2LED0 strap selects serial bus mode: [P2LED1,P2LED0] 00 = I2C master, 01 = I2C slave, 10 = SPI slave, 11 = SMI/MIIM. |
| 61 | P2LED0 | bidirectional | Port 2 LED (link/activity); with P2LED1 strap selects serial bus configuration mode. |
| 62 | RSTN | input | Hardware reset input, active-low, with internal pull-up. |
| 63 | FXSD1 | input | On MLL/RLL, connect to analog ground by a pull-down resistor (fiber signal detect on FLL). |
| 64 | VDDA_1.8 | power_in | 1.8V analog VDD input from VDDCO (pin 56) through external ferrite bead and capacitors. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Current | IIN | -10 | 10 | µA | VIN = GND ~ VDDIO | 75 | |
| Output Tri-State Leakage | /IOZ/ | 10 | µA | 75 | |||
| Input High Voltage (3.3V) | VIH | 2 | V | VDDIO = 3.3V | 75 | ||
| Input High Voltage (2.5V) | VIH | 1.8 | V | VDDIO = 2.5V | 75 | ||
| Input High Voltage (1.8V) | VIH | 1.3 | V | VDDIO = 1.8V | 75 | ||
| Input Low Voltage (3.3V) | VIL | 0.8 | V | VDDIO = 3.3V | 75 | ||
| Input Low Voltage (2.5V) | VIL | 0.7 | V | VDDIO = 2.5V | 75 | ||
| Input Low Voltage (1.8V) | VIL | 0.5 | V | VDDIO = 1.8V | 75 | ||
| Output High Voltage (3.3V) | VOH | 2.4 | V | IOH = -8 mA, VDDIO = 3.3V | 75 | ||
| Output High Voltage (2.5V) | VOH | 2 | V | IOH = -8 mA, VDDIO = 2.5V | 75 | ||
| Output High Voltage (1.8V) | VOH | 1.5 | V | IOH = -8 mA, VDDIO = 1.8V | 75 | ||
| Output Low Voltage (3.3V/2.5V) | VOL | 0.4 | V | IOL = 8 mA, VDDIO = 3.3V/2.5V | 75 | ||
| Output Low Voltage (1.8V) | VOL | 0.3 | V | IOL = 8 mA, VDDIO = 1.8V | 75 | ||
| 100BASE-TX Peak Differential Output Voltage | VO | 0.95 | 1.05 | V | 100Ω termination across differential output | 75 | |
| Output Voltage Imbalance | VIMB | 2 | % | 100Ω termination across differential output | 76 | ||
| Rise/Fall Time | tr/tf | 3 | 5 | ns | 76 | ||
| Rise/Fall Time Imbalance | 0 | 0.5 | ns | 76 | |||
| Duty Cycle Distortion | -0.5 | 0.5 | ns | 76 | |||
| Overshoot | 5 | % | 76 | ||||
| 100BASE-TX Output Jitter | 0.7 | 1.4 | ns | Peak-to-peak | 76 | ||
| 10BASE-T Transmit Output Jitter | 1.4 | 11 | ns | Peak-to-peak | 76 | ||
| EEPROM Setup time | ts1 | 20 | ns | 77 | |||
| EEPROM Hold time | th1 | 20 | ns | 77 | |||
| EEPROM Output valid | tov1 | 4096 | 4112 | 4128 | ns | 77 | |
| EEPROM Clock cycle | tcyc1 | 16384 | ns | 77 | |||
| Supply Voltage VDDA_1.8, VDDC | VIN | -0.5 | 2.4 | V | 74 | ||
| Supply Voltage VDDA_3.3, VDDIO | VIN | -0.5 | 4 | V | 74 | ||
| Input Voltage | -0.5 | 4 | V | 74 | |||
| Output Voltage | -0.5 | 4 | V | 74 | |||
| Lead Temperature | 260 | °C | soldering, 10s | 74 | |||
| Storage Temperature | TS | -55 | 150 | °C | 74 | ||
| HBM ESD Rating | -3 | 3 | kV | 74 | |||
| Operating Supply Voltage VDDA_1.8, VDDC | 1.66 | 1.94 | V | 74 | |||
| Operating Supply Voltage VDDA_3.3 | 2.5 | 3.465 | V | 74 | |||
| Operating Supply Voltage VDDIO | 1.71 | 3.465 | V | 74 | |||
| Ambient Temperature (Industrial) | TA | -40 | 85 | °C | Industrial | 74 | |
| Junction Temperature | TJ | 125 | °C | 74 | |||
| Thermal Resistance Junction-to-Ambient | ΘJA | 47.24 | °C/W | LQFP, no heat spreader | 74 | ||
| Thermal Resistance Junction-to-Case | ΘJC | 19.37 | °C/W | LQFP, no heat spreader | 74 | ||
| 100BASE-TX Supply Current (single 3.3V) | IDDXIO | 115 | mA | VDDA_3.3, VDDIO = 3.3V (single power), all ports 100% utilization | 75 | ||
| 10BASE-T Supply Current (single 3.3V) | IDDXIO | 85 | mA | VDDA_3.3, VDDIO = 3.3V, all ports 100% utilization | 75 | ||
| Power Saving Mode Current | IDD3 | 96 | mA | VDDA_3.3, VDDIO = 3.3V, unplug Port 1 and Port 2, Register 195 bit[1,0] = [1,1] | 75 | ||
| Soft Power Down Mode Current | IDD4 | 5 | mA | VDDA_3.3, VDDIO = 3.3V, Register 195 bit[1,0] = [1,0] | 75 | ||
| Energy Detect Mode Current | IDD5 | 15 | mA | VDDA_3.3, VDDIO = 3.3V, unplug Port 1 and Port 2 | 75 | ||
| 10BASE-T Squelch Threshold | VSQ | 400 | mV | 5 MHz square wave | 76 | ||
| 10BASE-T Peak Differential Output Voltage | VP | 2.4 | V | 100Ω termination across differential output | 76 |
CAD (KiCad official)
- Symbol:
KSZ8873MMLI - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
ksz8873mmli-etched.step/ksz8873mmli-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz8873mmli.step/ksz8873mmli.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (95 pp, sha256
5bfa1107d97e8afb, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).