← Commit history
ksz8851-16mlli: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)
2 files changed
+90−10
package.json+48−8@@ -71,7 +71,7 @@ "number": "4", "name": "INTRN", "type": "output",- "description": "Interrupt output (active low) to host CPU requiring external 4.7 k\u03a9 pull-up resistor when an interrupt status bit is set."+ "description": "Interrupt output (active low) to host CPU requiring external 4.7 kΩ pull-up resistor when an interrupt status bit is set." }, { "number": "5",@@ -107,7 +107,7 @@ "number": "10", "name": "EESK", "type": "output",- "description": "EEPROM serial clock output (4 \u03bcs or 800 ns cycle at 25 MHz or 125 MHz respectively) with internal pull-down during power-up/reset, latched for endian mode selection (pull-up=big endian, no connect/pull-down=little endian)."+ "description": "EEPROM serial clock output (4 μs or 800 ns cycle at 25 MHz or 125 MHz respectively) with internal pull-down during power-up/reset, latched for endian mode selection (pull-up=big endian, no connect/pull-down=little endian)." }, { "number": "11",@@ -161,13 +161,13 @@ "number": "19", "name": "TXP1", "type": "output",- "description": "Port 1 differential transmit signal (positive output) to isolation transformer with \u00b10.95V to \u00b11.05V peak differential voltage at 100\u03a9 termination."+ "description": "Port 1 differential transmit signal (positive output) to isolation transformer with ±0.95V to ±1.05V peak differential voltage at 100Ω termination." }, { "number": "20", "name": "TXM1", "type": "output",- "description": "Port 1 differential transmit signal (negative output) to isolation transformer with \u00b10.95V to \u00b11.05V peak differential voltage at 100\u03a9 termination."+ "description": "Port 1 differential transmit signal (negative output) to isolation transformer with ±0.95V to ±1.05V peak differential voltage at 100Ω termination." }, { "number": "21",@@ -179,7 +179,7 @@ "number": "22", "name": "ISET", "type": "output",- "description": "Transmit output current setting pin pulled to ground with 3.01 k\u03a9 1% resistor to set MAU current level."+ "description": "Transmit output current setting pin pulled to ground with 3.01 kΩ 1% resistor to set MAU current level." }, { "number": "23",@@ -191,7 +191,7 @@ "number": "24", "name": "X1", "type": "input",- "description": "25 MHz crystal or 3.3V oscillator input (\u00b150 ppm tolerance required) for system clock generation."+ "description": "25 MHz crystal or 3.3V oscillator input (±50 ppm tolerance required) for system clock generation." }, { "number": "25",@@ -372,6 +372,46 @@ "viewers": { "symbol": "viewers/symbol.html", "footprint": "viewers/footprint.html"- }+ },+ "models_3d": [+ {+ "file": "ksz8851-16mlli.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 9.0,+ 9.0,+ 1.5+ ],+ "zmin_mm": -0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "9dea352d93177c2904afd7d7b68ea8855ce1ab691f69f8b3e13655600514b6bf",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "ksz8851-16mlli-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 9.0,+ 9.0,+ 1.5+ ],+ "zmin_mm": -0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "29c69d583aa15dc9a6e79b4c3c28cf83fbe9ef29014a5405dec5c03601eaa244",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ] }-}+}
page.json+42−2@@ -357,7 +357,47 @@ "viewers": { "symbol": "viewers/symbol.html", "footprint": "viewers/footprint.html"- }+ },+ "models_3d": [+ {+ "file": "ksz8851-16mlli.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 9.0,+ 9.0,+ 1.5+ ],+ "zmin_mm": -0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "9dea352d93177c2904afd7d7b68ea8855ce1ab691f69f8b3e13655600514b6bf",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "ksz8851-16mlli-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 9.0,+ 9.0,+ 1.5+ ],+ "zmin_mm": -0.0,+ "centre_offset_mm": 0.0,+ "footprint_binding": "identity",+ "sha256": "29c69d583aa15dc9a6e79b4c3c28cf83fbe9ef29014a5405dec5c03601eaa244",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ] }, "metadata": { "specs": {@@ -405,4 +445,4 @@ "public": true }, "updated_at": "2026-09-24T23:25:09.516Z"-}+}