← Commit history

Initial commit: component/ksz8851-16mlli

Ray ·5217857fcd ·
2 files changed +467
README.mdadded+84
@@ -0,0 +1,84 @@+# KSZ8851-16MLLI++**Microchip Tech** · Ethernet Controllers · LQFP-48(7x7)++KSZ8851-16MLLI from Microchip Tech, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | P1LED1 | output | Programmable LED output indicating port activity or 100 Mbps speed (LED ON=LOW), used for 16-/8-bit bus mode selection during power-up/reset where no connect or pull-up selects 16-bit mode and pull-down selects 8-bit mode. |+| 2 | P1LED0 | output | Programmable LED output indicating link status or link/activity (LED ON=LOW) per Chip Global Control Register CGCR bit 9 setting. |+| 3 | PME | output | Power Management Event output (active low or high per PMECR[12]) asserted when wake-on-LAN events are detected (energy, linkup, magic packet, or wake-up frame). |+| 4 | INTRN | output | Interrupt output (active low) to host CPU requiring external 4.7 kΩ pull-up resistor when an interrupt status bit is set. |+| 5 | RDN | input | Asynchronous read strobe input (active low) indicating a read cycle with data valid 24-32 ns after RDN activation. |+| 6 | WRN | input | Asynchronous write strobe input (active low) indicating a write cycle requiring minimum 40 ns active time. |+| 7 | DGND | power_in | Digital ground reference. |+| 8 | VDD_CO1.8 | power_out | 1.8V regulator output providing power to VDD_A1.8 and VDD_D1.8 pins or left floating if external 1.8V supply is tied to VDD_IO pins. |+| 9 | EED_IO | bidirectional | EEPROM serial data I/O line for external EEPROM communication with internal pull-down during power-up/reset, latched to indicate EEPROM presence (pull-up=present, no connect/pull-down=absent). |+| 10 | EESK | output | EEPROM serial clock output (4 μs or 800 ns cycle at 25 MHz or 125 MHz respectively) with internal pull-down during power-up/reset, latched for endian mode selection (pull-up=big endian, no connect/pull-down=little endian). |+| 11 | CMD | input | Command type input selecting shared data bus access where low selects data access and high selects address/byte-enable access. |+| 12 | CSN | input | Chip select input (active low) enabling shared data bus access for read or write operations. |+| 13 | AGND | power_in | Analog ground reference. |+| 14 | VDD_A1.8 | power_in | 1.8V analog power supply from VDD_CO1.8 or external source (if VDD_IO=1.8V) requiring appropriate filtering capacitors. |+| 15 | EECS | output | EEPROM chip select output (active low) for selecting external EEPROM device during serial communication. |+| 16 | RXP1 | input | Port 1 differential receive signal (positive input) from isolation transformer for 10BASE-T/100BASE-TX physical layer. |+| 17 | RXM1 | input | Port 1 differential receive signal (negative input) from isolation transformer for 10BASE-T/100BASE-TX physical layer. |+| 18 | AGND | power_in | Analog ground reference. |+| 19 | TXP1 | output | Port 1 differential transmit signal (positive output) to isolation transformer with ±0.95V to ±1.05V peak differential voltage at 100Ω termination. |+| 20 | TXM1 | output | Port 1 differential transmit signal (negative output) to isolation transformer with ±0.95V to ±1.05V peak differential voltage at 100Ω termination. |+| 21 | VDD_A3.3 | power_in | 3.3V analog power supply input requiring appropriate decoupling capacitors. |+| 22 | ISET | output | Transmit output current setting pin pulled to ground with 3.01 kΩ 1% resistor to set MAU current level. |+| 23 | RSTN | input | Hardware reset input (active low) requiring minimum 10 ms low pulse after stable 3.3V supply voltage for proper device initialization. |+| 24 | X1 | input | 25 MHz crystal or 3.3V oscillator input (±50 ppm tolerance required) for system clock generation. |+| 25 | X2 | output | 25 MHz crystal output connection or no-connect if external oscillator is used for X1. |+| 26 | DGND | power_in | Digital ground reference. |+| 27 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital I/O power supply input for CPU interface logic requiring appropriate decoupling capacitors. |+| 28 | DGND | power_in | Digital ground reference. |+| 29 | VDD_D1.8 | power_in | 1.8V digital core power supply from VDD_CO1.8 or external source (if VDD_IO=1.8V) requiring appropriate filtering. |+| 30 | SD15 | bidirectional | Shared data bus bit 15 for data access when CMD=0; byte enable 3 (BE3, 4th byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 31 | SD14 | bidirectional | Shared data bus bit 14 for data access when CMD=0; byte enable 2 (BE2, 3rd byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 32 | SD13 | bidirectional | Shared data bus bit 13 for data access when CMD=0; byte enable 1 (BE1, 2nd byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 33 | SD12 | bidirectional | Shared data bus bit 12 for data access when CMD=0; byte enable 0 (BE0, 1st byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 34 | SD11 | bidirectional | Shared data bus bit 11 for data D11 access when CMD=0, do-not-care when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 35 | SD10 | bidirectional | Shared data bus bit 10 for data D10 access when CMD=0, do-not-care when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 36 | SD9 | bidirectional | Shared data bus bit 9 for data D9 access when CMD=0, do-not-care when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode. |+| 37 | DGND | power_in | Digital ground reference. |+| 38 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital I/O power supply input for CPU interface logic requiring appropriate decoupling capacitors. |+| 39 | SD8 | bidirectional | Shared data bus bit 8 for data D8 access when CMD=0, do-not-care when CMD=1; must be tied to GND in 8-bit mode. |+| 40 | SD7 | bidirectional | Shared data bus bit 7 for data D7 access when CMD=0, address A7 access when CMD=1 in both 8-bit and 16-bit modes. |+| 41 | SD6 | bidirectional | Shared data bus bit 6 for data D6 access when CMD=0, address A6 access when CMD=1 in both 8-bit and 16-bit modes. |+| 42 | SD5 | bidirectional | Shared data bus bit 5 for data D5 access when CMD=0, address A5 access when CMD=1 in both 8-bit and 16-bit modes. |+| 43 | SD4 | bidirectional | Shared data bus bit 4 for data D4 access when CMD=0, address A4 access when CMD=1 in both 8-bit and 16-bit modes. |+| 44 | SD3 | bidirectional | Shared data bus bit 3 for data D3 access when CMD=0, address A3 access when CMD=1 in both 8-bit and 16-bit modes. |+| 45 | SD2 | bidirectional | Shared data bus bit 2 for data D2 access when CMD=0, address A2 access when CMD=1 in both 8-bit and 16-bit modes. |+| 46 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital I/O power supply input for CPU interface logic requiring appropriate decoupling capacitors. |+| 47 | SD1 | bidirectional | Shared data bus bit 1 for data D1 access when CMD=0; address A1 access when CMD=1 in 8-bit mode, do-not-care when CMD=1 in 16-bit mode. |+| 48 | SD0 | bidirectional | Shared data bus bit 0 for data D0 access when CMD=0; address A0 access when CMD=1 in 8-bit mode, do-not-care when CMD=1 in 16-bit mode. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip Tech |+| Package | LQFP-48(7x7) |+| Category | Interface |+| Pins | 48 |++## CAD (KiCad official)++- Symbol: `KSZ8851-16MLLI`+- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`+- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)+- 3D model files: `ksz8851-16mlli-etched.step` / `ksz8851-16mlli-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ksz8851-16mlli.step` / `ksz8851-16mlli.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586184784834281472) (85 pp, sha256 `48923de9b6d88788`, retrieved 2026-09-18, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ksz8851-16mlli-datasheet.pdf)
page.jsonadded+383
@@ -0,0 +1,383 @@+{+  "slug": "ksz8851-16mlli",+  "version": "0.1.0",+  "type": "component",+  "description": "Microchip Tech Ethernet Controllers, LQFP-48(7x7). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "ksz8851-16mlli",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ksz8851-16mlli.kicad_sym",+    "ksz8851-16mlli.kicad_mod",+    "ksz8851-16mlli.glb",+    "ksz8851-16mlli.step",+    "ksz8851-16mlli.lbr",+    "docs/hero.png",+    "docs/ksz8851-16mlli-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "KSZ8851-16MLLI",+    "manufacturer": "Microchip Tech",+    "package": "LQFP-48(7x7)",+    "pin_count": 48,+    "category": "Interface",+    "subcategory": "Ethernet Controllers",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586184784834281472",+    "parts": {+      "symbol": "ksz8851-16mlli.kicad_sym",+      "footprint": "ksz8851-16mlli.kicad_mod",+      "model_3d": "ksz8851-16mlli-etched.glb",+      "model_3d_plain": "ksz8851-16mlli.glb",+      "model_3d_step": "ksz8851-16mlli-etched.step",+      "model_3d_step_plain": "ksz8851-16mlli.step",+      "lbr": "ksz8851-16mlli.lbr"+    },+    "distributor_links": {+      "lcsc": "C220270"+    },+    "pins": [+      {+        "number": "1",+        "name": "P1LED1",+        "type": "output",+        "description": "Programmable LED output indicating port activity or 100 Mbps speed (LED ON=LOW), used for 16-/8-bit bus mode selection during power-up/reset where no connect or pull-up selects 16-bit mode and pull-down selects 8-bit mode."+      },+      {+        "number": "2",+        "name": "P1LED0",+        "type": "output",+        "description": "Programmable LED output indicating link status or link/activity (LED ON=LOW) per Chip Global Control Register CGCR bit 9 setting."+      },+      {+        "number": "3",+        "name": "PME",+        "type": "output",+        "description": "Power Management Event output (active low or high per PMECR[12]) asserted when wake-on-LAN events are detected (energy, linkup, magic packet, or wake-up frame)."+      },+      {+        "number": "4",+        "name": "INTRN",+        "type": "output",+        "description": "Interrupt output (active low) to host CPU requiring external 4.7 kΩ pull-up resistor when an interrupt status bit is set."+      },+      {+        "number": "5",+        "name": "RDN",+        "type": "input",+        "description": "Asynchronous read strobe input (active low) indicating a read cycle with data valid 24-32 ns after RDN activation."+      },+      {+        "number": "6",+        "name": "WRN",+        "type": "input",+        "description": "Asynchronous write strobe input (active low) indicating a write cycle requiring minimum 40 ns active time."+      },+      {+        "number": "7",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference."+      },+      {+        "number": "8",+        "name": "VDD_CO1.8",+        "type": "power_out",+        "description": "1.8V regulator output providing power to VDD_A1.8 and VDD_D1.8 pins or left floating if external 1.8V supply is tied to VDD_IO pins."+      },+      {+        "number": "9",+        "name": "EED_IO",+        "type": "bidirectional",+        "description": "EEPROM serial data I/O line for external EEPROM communication with internal pull-down during power-up/reset, latched to indicate EEPROM presence (pull-up=present, no connect/pull-down=absent)."+      },+      {+        "number": "10",+        "name": "EESK",+        "type": "output",+        "description": "EEPROM serial clock output (4 μs or 800 ns cycle at 25 MHz or 125 MHz respectively) with internal pull-down during power-up/reset, latched for endian mode selection (pull-up=big endian, no connect/pull-down=little endian)."+      },+      {+        "number": "11",+        "name": "CMD",+        "type": "input",+        "description": "Command type input selecting shared data bus access where low selects data access and high selects address/byte-enable access."+      },+      {+        "number": "12",+        "name": "CSN",+        "type": "input",+        "description": "Chip select input (active low) enabling shared data bus access for read or write operations."+      },+      {+        "number": "13",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference."+      },+      {+        "number": "14",+        "name": "VDD_A1.8",+        "type": "power_in",+        "description": "1.8V analog power supply from VDD_CO1.8 or external source (if VDD_IO=1.8V) requiring appropriate filtering capacitors."+      },+      {+        "number": "15",+        "name": "EECS",+        "type": "output",+        "description": "EEPROM chip select output (active low) for selecting external EEPROM device during serial communication."+      },+      {+        "number": "16",+        "name": "RXP1",+        "type": "input",+        "description": "Port 1 differential receive signal (positive input) from isolation transformer for 10BASE-T/100BASE-TX physical layer."+      },+      {+        "number": "17",+        "name": "RXM1",+        "type": "input",+        "description": "Port 1 differential receive signal (negative input) from isolation transformer for 10BASE-T/100BASE-TX physical layer."+      },+      {+        "number": "18",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground reference."+      },+      {+        "number": "19",+        "name": "TXP1",+        "type": "output",+        "description": "Port 1 differential transmit signal (positive output) to isolation transformer with ±0.95V to ±1.05V peak differential voltage at 100Ω termination."+      },+      {+        "number": "20",+        "name": "TXM1",+        "type": "output",+        "description": "Port 1 differential transmit signal (negative output) to isolation transformer with ±0.95V to ±1.05V peak differential voltage at 100Ω termination."+      },+      {+        "number": "21",+        "name": "VDD_A3.3",+        "type": "power_in",+        "description": "3.3V analog power supply input requiring appropriate decoupling capacitors."+      },+      {+        "number": "22",+        "name": "ISET",+        "type": "output",+        "description": "Transmit output current setting pin pulled to ground with 3.01 kΩ 1% resistor to set MAU current level."+      },+      {+        "number": "23",+        "name": "RSTN",+        "type": "input",+        "description": "Hardware reset input (active low) requiring minimum 10 ms low pulse after stable 3.3V supply voltage for proper device initialization."+      },+      {+        "number": "24",+        "name": "X1",+        "type": "input",+        "description": "25 MHz crystal or 3.3V oscillator input (±50 ppm tolerance required) for system clock generation."+      },+      {+        "number": "25",+        "name": "X2",+        "type": "output",+        "description": "25 MHz crystal output connection or no-connect if external oscillator is used for X1."+      },+      {+        "number": "26",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference."+      },+      {+        "number": "27",+        "name": "VDD_IO",+        "type": "power_in",+        "description": "3.3V, 2.5V, or 1.8V digital I/O power supply input for CPU interface logic requiring appropriate decoupling capacitors."+      },+      {+        "number": "28",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference."+      },+      {+        "number": "29",+        "name": "VDD_D1.8",+        "type": "power_in",+        "description": "1.8V digital core power supply from VDD_CO1.8 or external source (if VDD_IO=1.8V) requiring appropriate filtering."+      },+      {+        "number": "30",+        "name": "SD15",+        "type": "bidirectional",+        "description": "Shared data bus bit 15 for data access when CMD=0; byte enable 3 (BE3, 4th byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "31",+        "name": "SD14",+        "type": "bidirectional",+        "description": "Shared data bus bit 14 for data access when CMD=0; byte enable 2 (BE2, 3rd byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "32",+        "name": "SD13",+        "type": "bidirectional",+        "description": "Shared data bus bit 13 for data access when CMD=0; byte enable 1 (BE1, 2nd byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "33",+        "name": "SD12",+        "type": "bidirectional",+        "description": "Shared data bus bit 12 for data access when CMD=0; byte enable 0 (BE0, 1st byte enable, active high) when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "34",+        "name": "SD11",+        "type": "bidirectional",+        "description": "Shared data bus bit 11 for data D11 access when CMD=0, do-not-care when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "35",+        "name": "SD10",+        "type": "bidirectional",+        "description": "Shared data bus bit 10 for data D10 access when CMD=0, do-not-care when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "36",+        "name": "SD9",+        "type": "bidirectional",+        "description": "Shared data bus bit 9 for data D9 access when CMD=0, do-not-care when CMD=1 in 16-bit mode; must be tied to GND in 8-bit mode."+      },+      {+        "number": "37",+        "name": "DGND",+        "type": "power_in",+        "description": "Digital ground reference."+      },+      {+        "number": "38",+        "name": "VDD_IO",+        "type": "power_in",+        "description": "3.3V, 2.5V, or 1.8V digital I/O power supply input for CPU interface logic requiring appropriate decoupling capacitors."+      },+      {+        "number": "39",+        "name": "SD8",+        "type": "bidirectional",+        "description": "Shared data bus bit 8 for data D8 access when CMD=0, do-not-care when CMD=1; must be tied to GND in 8-bit mode."+      },+      {+        "number": "40",+        "name": "SD7",+        "type": "bidirectional",+        "description": "Shared data bus bit 7 for data D7 access when CMD=0, address A7 access when CMD=1 in both 8-bit and 16-bit modes."+      },+      {+        "number": "41",+        "name": "SD6",+        "type": "bidirectional",+        "description": "Shared data bus bit 6 for data D6 access when CMD=0, address A6 access when CMD=1 in both 8-bit and 16-bit modes."+      },+      {+        "number": "42",+        "name": "SD5",+        "type": "bidirectional",+        "description": "Shared data bus bit 5 for data D5 access when CMD=0, address A5 access when CMD=1 in both 8-bit and 16-bit modes."+      },+      {+        "number": "43",+        "name": "SD4",+        "type": "bidirectional",+        "description": "Shared data bus bit 4 for data D4 access when CMD=0, address A4 access when CMD=1 in both 8-bit and 16-bit modes."+      },+      {+        "number": "44",+        "name": "SD3",+        "type": "bidirectional",+        "description": "Shared data bus bit 3 for data D3 access when CMD=0, address A3 access when CMD=1 in both 8-bit and 16-bit modes."+      },+      {+        "number": "45",+        "name": "SD2",+        "type": "bidirectional",+        "description": "Shared data bus bit 2 for data D2 access when CMD=0, address A2 access when CMD=1 in both 8-bit and 16-bit modes."+      },+      {+        "number": "46",+        "name": "VDD_IO",+        "type": "power_in",+        "description": "3.3V, 2.5V, or 1.8V digital I/O power supply input for CPU interface logic requiring appropriate decoupling capacitors."+      },+      {+        "number": "47",+        "name": "SD1",+        "type": "bidirectional",+        "description": "Shared data bus bit 1 for data D1 access when CMD=0; address A1 access when CMD=1 in 8-bit mode, do-not-care when CMD=1 in 16-bit mode."+      },+      {+        "number": "48",+        "name": "SD0",+        "type": "bidirectional",+        "description": "Shared data bus bit 0 for data D0 access when CMD=0; address A0 access when CMD=1 in 8-bit mode, do-not-care when CMD=1 in 16-bit mode."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: RXP1 and RXM1 (pins 16-17) are listed as I/O in datasheet buffer type but function as differential r; P1LED1 (pin 1) is listed as IPU/O with internal pull-up during power-up/reset, used for bus mode sel; EESK (pin 10) is listed as IPD/O with internal pull-down during power-up/reset for endian selection,"+        ],+        "pages_sent": 85,+        "cost_usd": 1.0273,+        "at": "2026-09-18T06:08:14"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586184784834281472",+        "pages": 85,+        "sha256": "48923de9b6d88788",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 48,+        "described": 48,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file