main
Ray
Publish 0.1.0
4b53ac1
KSZ8842-16MVLI-TR
Microchip Tech · Ethernet Transceivers · LQFP-128(14x14)
KSZ8842-16MVLI-TR from Microchip Tech, in a LQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TEST_EN | input | Test enable; for normal operation pull down to ground. |
| 2 | SCAN_EN | input | Scan test scan mux enable; for normal operation pull down to ground. |
| 3 | P1LED2 | output | Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 4 | P1LED1 | output | Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 5 | P1LED0 | output | Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 6 | P2LED2 | output | Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 7 | P2LED1 | output | Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 8 | P2LED0 | output | Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 9 | DGND | power_in | Digital ground. |
| 10 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 11 | RDYRTNN | input | Ready return not; asserted by host to complete synchronous reads in VLBus-like mode, or driven low for wait states in 32-bit burst mode. |
| 12 | BCLK | input | Local bus clock for synchronous bus systems; maximum frequency is 50 MHz; tie low or unconnected in asynchronous mode. |
| 13 | NC | unconnected | No connect. |
| 14 | NC | unconnected | No connect. |
| 15 | SRDYN | output | Synchronous ready not; falling edge indicates ready in VLBus-like mode, synchronous to BCLK. |
| 16 | INTRN | output | Active-low interrupt to host CPU; requires an external 4.7 kΩ pull-up resistor. |
| 17 | LDEVN | output | Active-low output asserted when AEN is low and A15-A4 decode to the programmed base address. |
| 18 | RDN | input | Asynchronous active-low read strobe. |
| 19 | EECS | output | EEPROM chip select. |
| 20 | ARDY | output | Asynchronous ready used to extend bus access cycles; requires an external 4.7 kΩ pull-up resistor. |
| 21 | CYCLEN | input | Cycle signal; follows the addressing cycle to signal the command cycle in VLBus-like mode. |
| 22 | P2LED3 | output | Port 2 LED indicator with internal pull-down; see pins 6, 7 and 8. |
| 23 | DGND | power_in | Digital IO ground. |
| 24 | VDDCO | power_out | 1.2V digital core voltage output from the internal LDO; supplies VDDC, VDDA and VDDAP; do not connect an external supply. |
| 25 | VLBUSN | input | Bus mode select: pull-down or float selects synchronous mode; pull-up selects 8/16-bit asynchronous or EISA-like burst mode. |
| 26 | EEEN | input | EEPROM enable; EEPROM is enabled and connected when pulled up, and disabled when pulled down or no connect. |
| 27 | P1LED3 | output | Port 1 LED indicator with internal pull-down; see pins 3, 4 and 5. |
| 28 | EEDO | output | EEPROM data out; connected to the DI input of the serial EEPROM. |
| 29 | EESK | output | EEPROM serial clock to load configuration; 4 µs cycle at 25 MHz on-chip bus speed or 800 ns at 125 MHz. |
| 30 | EEDI | input | EEPROM data in; connected to the DO output of the serial EEPROM when EEEN is pulled up. |
| 31 | SWR | input | Synchronous write/read; write cycles when high and read cycles when low. |
| 32 | AEN | input | Address enable; active-low address qualifier for address decoding. |
| 33 | WRN | input | Asynchronous active-low write strobe. |
| 34 | DGND | power_in | Digital IO ground. |
| 35 | ADSN | input | Address strobe not; the rising edge latches A15-A1 and AEN. |
| 36 | PWRDN | input | Full-chip power-down; low powers down the chip, high or floating is normal operation. |
| 37 | AGND | power_in | Analog ground. |
| 38 | VDDA | power_in | 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 39 | AGND | power_in | Analog ground. |
| 40 | NC | unconnected | No connect. |
| 41 | NC | unconnected | No connect. |
| 42 | AGND | power_in | Analog ground. |
| 43 | VDDA | power_in | 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 44 | NC | unconnected | No connect. |
| 45 | RXP1 | bidirectional | Port 1 physical receive (MDI) or transmit signal, + differential. |
| 46 | RXM1 | bidirectional | Port 1 physical receive (MDI) or transmit signal, - differential. |
| 47 | AGND | power_in | Analog ground. |
| 48 | TXP1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, + differential. |
| 49 | TXM1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, - differential. |
| 50 | VDDATX | power_in | 3.3V analog VDD input power supply with well decoupling capacitors. |
| 51 | VDDARX | power_in | 3.3V analog VDD input power supply with well decoupling capacitors. |
| 52 | RXM2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, - differential. |
| 53 | RXP2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, + differential. |
| 54 | AGND | power_in | Analog ground. |
| 55 | TXM2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, - differential. |
| 56 | TXP2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, + differential. |
| 57 | VDDA | power_in | 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 58 | AGND | power_in | Analog ground. |
| 59 | NC | unconnected | No connect. |
| 60 | NC | unconnected | No connect. |
| 61 | ISET | output | Sets physical transmit output current; pull down with a 3.01 kΩ 1% resistor to ground. |
| 62 | AGND | power_in | Analog ground. |
| 63 | VDDAP | power_in | 1.2V analog VDD for PLL supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 64 | AGND | power_in | Analog ground. |
| 65 | X1 | input | 25 MHz crystal or oscillator clock input; clock requirement ±50 ppm; a 3.3V tolerant oscillator may drive X1. |
| 66 | X2 | output | Crystal connection for the 25 MHz clock; no connect when an oscillator is used. |
| 67 | RSTN | input | Hardware reset, active-low; requires a minimum of 10 ms low after the 3.3V supply is stable. |
| 68 | A15 | input | Address bit 15 input. |
| 69 | A14 | input | Address bit 14 input. |
| 70 | A13 | input | Address bit 13 input. |
| 71 | A12 | input | Address bit 12 input. |
| 72 | A11 | input | Address bit 11 input. |
| 73 | A10 | input | Address bit 10 input. |
| 74 | A9 | input | Address bit 9 input. |
| 75 | A8 | input | Address bit 8 input. |
| 76 | A7 | input | Address bit 7 input. |
| 77 | A6 | input | Address bit 6 input. |
| 78 | DGND | power_in | Digital IO ground. |
| 79 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 80 | A5 | input | Address bit 5 input. |
| 81 | A4 | input | Address bit 4 input. |
| 82 | A3 | input | Address bit 3 input. |
| 83 | A2 | input | Address bit 2 input. |
| 84 | A1 | input | Address bit 1 input. |
| 85 | NC | unconnected | No connect. |
| 86 | NC | unconnected | No connect. |
| 87 | BE1N | input | Active-low byte enable 1 for data byte 1; don't care in 8-bit bus mode. |
| 88 | BE0N | input | Active-low byte enable 0 for data byte 0; internally inverted and connected to BE1N in 8-bit bus mode. |
| 89 | NC | unconnected | No connect. |
| 90 | DGND | power_in | Digital core ground. |
| 91 | VDDC | power_in | 1.2V digital core VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 92 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 93 | NC | unconnected | No connect. |
| 94 | NC | unconnected | No connect. |
| 95 | NC | unconnected | No connect. |
| 96 | NC | unconnected | No connect. |
| 97 | NC | unconnected | No connect. |
| 98 | NC | unconnected | No connect. |
| 99 | NC | unconnected | No connect. |
| 100 | NC | unconnected | No connect. |
| 101 | NC | unconnected | No connect. |
| 102 | NC | unconnected | No connect. |
| 103 | NC | unconnected | No connect. |
| 104 | NC | unconnected | No connect. |
| 105 | NC | unconnected | No connect. |
| 106 | NC | unconnected | No connect. |
| 107 | DGND | power_in | Digital IO ground. |
| 108 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 109 | NC | unconnected | No connect. |
| 110 | D15 | bidirectional | Data bus bit 15. |
| 111 | D14 | bidirectional | Data bus bit 14. |
| 112 | D13 | bidirectional | Data bus bit 13. |
| 113 | D12 | bidirectional | Data bus bit 12. |
| 114 | D11 | bidirectional | Data bus bit 11. |
| 115 | D10 | bidirectional | Data bus bit 10. |
| 116 | D9 | bidirectional | Data bus bit 9. |
| 117 | D8 | bidirectional | Data bus bit 8. |
| 118 | D7 | bidirectional | Data bus bit 7. |
| 119 | D6 | bidirectional | Data bus bit 6. |
| 120 | D5 | bidirectional | Data bus bit 5. |
| 121 | D4 | bidirectional | Data bus bit 4. |
| 122 | D3 | bidirectional | Data bus bit 3. |
| 123 | DGND | power_in | Digital IO ground. |
| 124 | DGND | power_in | Digital core ground. |
| 125 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 126 | D2 | bidirectional | Data bus bit 2. |
| 127 | D1 | bidirectional | Data bus bit 1. |
| 128 | D0 | bidirectional | Data bus bit 0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | LQFP-128(14x14) |
| Category | Communication Interface Chip |
| Pins | 128 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input High Voltage | VIH | 2 | V | 110 | |||
| Input Low Voltage | VIL | 0.8 | V | 110 | |||
| Input Current | IIN | -10 | 10 | μA | VIN = GND ~ VDDIO | 110 | |
| Output High Voltage | VOH | 2.4 | V | IOH = -8 mA | 110 | ||
| Output Low Voltage | VOL | 0.4 | V | IOL = 8 mA | 110 | ||
| Output Tri-State Leakage | /IOZ/ | 10 | μA | 110 | |||
| Peak Differential Output Voltage | VO | -0.95 | 1.05 | V | 100Ω termination on the differential output. | 110 | |
| Output Voltage Imbalance | VIMB | 2 | % | 100Ω termination on the differential output. | 110 | ||
| Rise/Fall Time | tr/tf | 3 | 5 | ns | 110 | ||
| Rise/Fall Time Imbalance | 0 | 0.5 | ns | 110 | |||
| Duty Cycle Distortion | -0.25 | 0.25 | ns | 110 | |||
| Overshoot | 5 | % | 110 | ||||
| Output Jitter (100BASE-TX) | 0.7 | 1.4 | ns | Peak-to-peak | 110 | ||
| Output Jitter (10BASE-T) | 1.8 | 3.5 | ns | Peak-to-peak | 110 | ||
| Supply Voltage (VDDATX, VDDARX, VDDIO) | -0.5 | 4 | V | 109 | |||
| Input Voltage (all inputs) | -0.5 | 5 | V | 109 | |||
| Output Voltage (all outputs) | -0.5 | 4 | V | 109 | |||
| Storage Temperature | TS | -55 | 150 | °C | 109 | ||
| Lead Temperature (Soldering) | 270 | °C | Soldering, 10 sec | 109 | |||
| Supply Voltage (VDDATX, VDDARX, VDDIO) | 3.1 | 3.5 | V | 109 | |||
| Ambient Operating Temperature (industrial option) | TA | -40 | 85 | °C | Industrial Temperature Range (Features, page 1) | 1 | |
| Maximum Junction Temperature | TJ | 125 | °C | 109 | |||
| Thermal Resistance (junction-to-ambient) | ΘJA | 42.91 | °C/W | Note 5-1: no heat spreader; air velocity 0 m/s | 109 | ||
| Thermal Resistance (junction-to-case) | ΘJC | 19.6 | °C/W | Note 5-1: no heat spreader; air velocity 0 m/s | 109 | ||
| Stable supply voltages to reset high | tSR | 10 | ms | 121 | |||
| Address valid to RDN/WRN active | t1 | 0 | ns | A1-A15, AEN, BExN[3:0] valid to RDN, WRN active | 111 | ||
| Address hold after RDN inactive | t2 | 0 | ns | Assume ADSN tied Low | 111 | ||
| Address hold after WRN inactive | t2 | 1 | ns | Assume ADSN tied Low | 111 | ||
| Read data valid to ARDY rising | t3 | 0.8 | ns | 111 | |||
| Read data hold after RDN inactive | t4 | 4 | ns | 111 | |||
| Write data setup to WRN inactive | t5 | 4 | ns | 111 | |||
| Write data hold after WRN inactive | t6 | 2 | ns | 111 | |||
| Read active to ARDY Low | t7 | 8 | ns | 111 | |||
| Write inactive to ARDY Low | t8 | 8 | ns | 111 |
CAD (KiCad official)
- Symbol:
KSZ8842-16MVLI-TR - Footprint:
Package_QFP:LQFP-128_14x14mm_P0.4mm - 3D model: LQFP-128(14x14) (KiCad packages3D, STEP)
- 3D model files:
ksz8842-16mvli-tr-etched.step/ksz8842-16mvli-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz8842-16mvli-tr.step/ksz8842-16mvli-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (132 pp, sha256
36e29b760fb0e430, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# KSZ8842-16MVLI-TR
**Microchip Tech** · Ethernet Transceivers · LQFP-128(14x14)
KSZ8842-16MVLI-TR from Microchip Tech, in a LQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TEST_EN | input | Test enable; for normal operation pull down to ground. |
| 2 | SCAN_EN | input | Scan test scan mux enable; for normal operation pull down to ground. |
| 3 | P1LED2 | output | Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 4 | P1LED1 | output | Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 5 | P1LED0 | output | Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 6 | P2LED2 | output | Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 7 | P2LED1 | output | Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 8 | P2LED0 | output | Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits. |
| 9 | DGND | power_in | Digital ground. |
| 10 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 11 | RDYRTNN | input | Ready return not; asserted by host to complete synchronous reads in VLBus-like mode, or driven low for wait states in 32-bit burst mode. |
| 12 | BCLK | input | Local bus clock for synchronous bus systems; maximum frequency is 50 MHz; tie low or unconnected in asynchronous mode. |
| 13 | NC | unconnected | No connect. |
| 14 | NC | unconnected | No connect. |
| 15 | SRDYN | output | Synchronous ready not; falling edge indicates ready in VLBus-like mode, synchronous to BCLK. |
| 16 | INTRN | output | Active-low interrupt to host CPU; requires an external 4.7 kΩ pull-up resistor. |
| 17 | LDEVN | output | Active-low output asserted when AEN is low and A15-A4 decode to the programmed base address. |
| 18 | RDN | input | Asynchronous active-low read strobe. |
| 19 | EECS | output | EEPROM chip select. |
| 20 | ARDY | output | Asynchronous ready used to extend bus access cycles; requires an external 4.7 kΩ pull-up resistor. |
| 21 | CYCLEN | input | Cycle signal; follows the addressing cycle to signal the command cycle in VLBus-like mode. |
| 22 | P2LED3 | output | Port 2 LED indicator with internal pull-down; see pins 6, 7 and 8. |
| 23 | DGND | power_in | Digital IO ground. |
| 24 | VDDCO | power_out | 1.2V digital core voltage output from the internal LDO; supplies VDDC, VDDA and VDDAP; do not connect an external supply. |
| 25 | VLBUSN | input | Bus mode select: pull-down or float selects synchronous mode; pull-up selects 8/16-bit asynchronous or EISA-like burst mode. |
| 26 | EEEN | input | EEPROM enable; EEPROM is enabled and connected when pulled up, and disabled when pulled down or no connect. |
| 27 | P1LED3 | output | Port 1 LED indicator with internal pull-down; see pins 3, 4 and 5. |
| 28 | EEDO | output | EEPROM data out; connected to the DI input of the serial EEPROM. |
| 29 | EESK | output | EEPROM serial clock to load configuration; 4 µs cycle at 25 MHz on-chip bus speed or 800 ns at 125 MHz. |
| 30 | EEDI | input | EEPROM data in; connected to the DO output of the serial EEPROM when EEEN is pulled up. |
| 31 | SWR | input | Synchronous write/read; write cycles when high and read cycles when low. |
| 32 | AEN | input | Address enable; active-low address qualifier for address decoding. |
| 33 | WRN | input | Asynchronous active-low write strobe. |
| 34 | DGND | power_in | Digital IO ground. |
| 35 | ADSN | input | Address strobe not; the rising edge latches A15-A1 and AEN. |
| 36 | PWRDN | input | Full-chip power-down; low powers down the chip, high or floating is normal operation. |
| 37 | AGND | power_in | Analog ground. |
| 38 | VDDA | power_in | 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 39 | AGND | power_in | Analog ground. |
| 40 | NC | unconnected | No connect. |
| 41 | NC | unconnected | No connect. |
| 42 | AGND | power_in | Analog ground. |
| 43 | VDDA | power_in | 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 44 | NC | unconnected | No connect. |
| 45 | RXP1 | bidirectional | Port 1 physical receive (MDI) or transmit signal, + differential. |
| 46 | RXM1 | bidirectional | Port 1 physical receive (MDI) or transmit signal, - differential. |
| 47 | AGND | power_in | Analog ground. |
| 48 | TXP1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, + differential. |
| 49 | TXM1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, - differential. |
| 50 | VDDATX | power_in | 3.3V analog VDD input power supply with well decoupling capacitors. |
| 51 | VDDARX | power_in | 3.3V analog VDD input power supply with well decoupling capacitors. |
| 52 | RXM2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, - differential. |
| 53 | RXP2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, + differential. |
| 54 | AGND | power_in | Analog ground. |
| 55 | TXM2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, - differential. |
| 56 | TXP2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, + differential. |
| 57 | VDDA | power_in | 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 58 | AGND | power_in | Analog ground. |
| 59 | NC | unconnected | No connect. |
| 60 | NC | unconnected | No connect. |
| 61 | ISET | output | Sets physical transmit output current; pull down with a 3.01 kΩ 1% resistor to ground. |
| 62 | AGND | power_in | Analog ground. |
| 63 | VDDAP | power_in | 1.2V analog VDD for PLL supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 64 | AGND | power_in | Analog ground. |
| 65 | X1 | input | 25 MHz crystal or oscillator clock input; clock requirement ±50 ppm; a 3.3V tolerant oscillator may drive X1. |
| 66 | X2 | output | Crystal connection for the 25 MHz clock; no connect when an oscillator is used. |
| 67 | RSTN | input | Hardware reset, active-low; requires a minimum of 10 ms low after the 3.3V supply is stable. |
| 68 | A15 | input | Address bit 15 input. |
| 69 | A14 | input | Address bit 14 input. |
| 70 | A13 | input | Address bit 13 input. |
| 71 | A12 | input | Address bit 12 input. |
| 72 | A11 | input | Address bit 11 input. |
| 73 | A10 | input | Address bit 10 input. |
| 74 | A9 | input | Address bit 9 input. |
| 75 | A8 | input | Address bit 8 input. |
| 76 | A7 | input | Address bit 7 input. |
| 77 | A6 | input | Address bit 6 input. |
| 78 | DGND | power_in | Digital IO ground. |
| 79 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 80 | A5 | input | Address bit 5 input. |
| 81 | A4 | input | Address bit 4 input. |
| 82 | A3 | input | Address bit 3 input. |
| 83 | A2 | input | Address bit 2 input. |
| 84 | A1 | input | Address bit 1 input. |
| 85 | NC | unconnected | No connect. |
| 86 | NC | unconnected | No connect. |
| 87 | BE1N | input | Active-low byte enable 1 for data byte 1; don't care in 8-bit bus mode. |
| 88 | BE0N | input | Active-low byte enable 0 for data byte 0; internally inverted and connected to BE1N in 8-bit bus mode. |
| 89 | NC | unconnected | No connect. |
| 90 | DGND | power_in | Digital core ground. |
| 91 | VDDC | power_in | 1.2V digital core VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor. |
| 92 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 93 | NC | unconnected | No connect. |
| 94 | NC | unconnected | No connect. |
| 95 | NC | unconnected | No connect. |
| 96 | NC | unconnected | No connect. |
| 97 | NC | unconnected | No connect. |
| 98 | NC | unconnected | No connect. |
| 99 | NC | unconnected | No connect. |
| 100 | NC | unconnected | No connect. |
| 101 | NC | unconnected | No connect. |
| 102 | NC | unconnected | No connect. |
| 103 | NC | unconnected | No connect. |
| 104 | NC | unconnected | No connect. |
| 105 | NC | unconnected | No connect. |
| 106 | NC | unconnected | No connect. |
| 107 | DGND | power_in | Digital IO ground. |
| 108 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 109 | NC | unconnected | No connect. |
| 110 | D15 | bidirectional | Data bus bit 15. |
| 111 | D14 | bidirectional | Data bus bit 14. |
| 112 | D13 | bidirectional | Data bus bit 13. |
| 113 | D12 | bidirectional | Data bus bit 12. |
| 114 | D11 | bidirectional | Data bus bit 11. |
| 115 | D10 | bidirectional | Data bus bit 10. |
| 116 | D9 | bidirectional | Data bus bit 9. |
| 117 | D8 | bidirectional | Data bus bit 8. |
| 118 | D7 | bidirectional | Data bus bit 7. |
| 119 | D6 | bidirectional | Data bus bit 6. |
| 120 | D5 | bidirectional | Data bus bit 5. |
| 121 | D4 | bidirectional | Data bus bit 4. |
| 122 | D3 | bidirectional | Data bus bit 3. |
| 123 | DGND | power_in | Digital IO ground. |
| 124 | DGND | power_in | Digital core ground. |
| 125 | VDDIO | power_in | 3.3V digital VDDIO input power supply for IO with well decoupling capacitors. |
| 126 | D2 | bidirectional | Data bus bit 2. |
| 127 | D1 | bidirectional | Data bus bit 1. |
| 128 | D0 | bidirectional | Data bus bit 0. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | LQFP-128(14x14) |
| Category | Communication Interface Chip |
| Pins | 128 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input High Voltage | VIH | 2 | | | V | | 110 |
| Input Low Voltage | VIL | | | 0.8 | V | | 110 |
| Input Current | IIN | -10 | | 10 | μA | VIN = GND ~ VDDIO | 110 |
| Output High Voltage | VOH | 2.4 | | | V | IOH = -8 mA | 110 |
| Output Low Voltage | VOL | | | 0.4 | V | IOL = 8 mA | 110 |
| Output Tri-State Leakage | /IOZ/ | | | 10 | μA | | 110 |
| Peak Differential Output Voltage | VO | -0.95 | | 1.05 | V | 100Ω termination on the differential output. | 110 |
| Output Voltage Imbalance | VIMB | | | 2 | % | 100Ω termination on the differential output. | 110 |
| Rise/Fall Time | tr/tf | 3 | | 5 | ns | | 110 |
| Rise/Fall Time Imbalance | | | 0 | 0.5 | ns | | 110 |
| Duty Cycle Distortion | | -0.25 | | 0.25 | ns | | 110 |
| Overshoot | | | | 5 | % | | 110 |
| Output Jitter (100BASE-TX) | | | 0.7 | 1.4 | ns | Peak-to-peak | 110 |
| Output Jitter (10BASE-T) | | | 1.8 | 3.5 | ns | Peak-to-peak | 110 |
| Supply Voltage (VDDATX, VDDARX, VDDIO) | | -0.5 | | 4 | V | | 109 |
| Input Voltage (all inputs) | | -0.5 | | 5 | V | | 109 |
| Output Voltage (all outputs) | | -0.5 | | 4 | V | | 109 |
| Storage Temperature | TS | -55 | | 150 | °C | | 109 |
| Lead Temperature (Soldering) | | | | 270 | °C | Soldering, 10 sec | 109 |
| Supply Voltage (VDDATX, VDDARX, VDDIO) | | 3.1 | | 3.5 | V | | 109 |
| Ambient Operating Temperature (industrial option) | TA | -40 | | 85 | °C | Industrial Temperature Range (Features, page 1) | 1 |
| Maximum Junction Temperature | TJ | | | 125 | °C | | 109 |
| Thermal Resistance (junction-to-ambient) | ΘJA | | 42.91 | | °C/W | Note 5-1: no heat spreader; air velocity 0 m/s | 109 |
| Thermal Resistance (junction-to-case) | ΘJC | | 19.6 | | °C/W | Note 5-1: no heat spreader; air velocity 0 m/s | 109 |
| Stable supply voltages to reset high | tSR | 10 | | | ms | | 121 |
| Address valid to RDN/WRN active | t1 | 0 | | | ns | A1-A15, AEN, BExN[3:0] valid to RDN, WRN active | 111 |
| Address hold after RDN inactive | t2 | 0 | | | ns | Assume ADSN tied Low | 111 |
| Address hold after WRN inactive | t2 | 1 | | | ns | Assume ADSN tied Low | 111 |
| Read data valid to ARDY rising | t3 | | | 0.8 | ns | | 111 |
| Read data hold after RDN inactive | t4 | 4 | | | ns | | 111 |
| Write data setup to WRN inactive | t5 | 4 | | | ns | | 111 |
| Write data hold after WRN inactive | t6 | 2 | | | ns | | 111 |
| Read active to ARDY Low | t7 | | | 8 | ns | | 111 |
| Write inactive to ARDY Low | t8 | | | 8 | ns | | 111 |
## CAD (KiCad official)
- Symbol: `KSZ8842-16MVLI-TR`
- Footprint: `Package_QFP:LQFP-128_14x14mm_P0.4mm`
- 3D model: LQFP-128(14x14) (KiCad packages3D, STEP)
- 3D model files: `ksz8842-16mvli-tr-etched.step` / `ksz8842-16mvli-tr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ksz8842-16mvli-tr.step` / `ksz8842-16mvli-tr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/ksz8842-16mvli-tr-datasheet.pdf) (132 pp, sha256 `36e29b760fb0e430`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ksz8842-16mvli-tr-datasheet.pdf)