main
Ray
Publish 0.1.0
5e471ab
KSZ8463MLI
Microchip Tech · Interface - Specialized · LQFP-64(10x10)
KSZ8463MLI from Microchip Tech, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RXM1 | bidirectional | Port 1 physical receive (MDI) or transmit (MDI-X) signal, negative differential. |
| 2 | RXP1 | bidirectional | Port 1 physical receive (MDI) or transmit (MDI-X) signal, positive differential. |
| 3 | AGND | power_in | Analog ground. |
| 4 | TXM1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, negative differential. |
| 5 | TXP1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, positive differential. |
| 6 | VDD_AL | power_in | Filtered low-voltage analog power input, to be filtered with a ferrite bead and capacitors. |
| 7 | ISET | output | Sets the physical transmit output current; pull down with a 6.49 kΩ (1%) resistor to ground. |
| 8 | AGND | power_in | Analog ground. |
| 9 | VDD_A3.3 | power_in | 3.3V analog VDD input power supply, must be well decoupled. |
| 10 | RXM2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, negative differential. |
| 11 | RXP2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, positive differential. |
| 12 | AGND | power_in | Analog ground. |
| 13 | TXM2 | bidirectional | Port 2 physical transmit (MDI) or receive (MDI-X) signal, negative differential. |
| 14 | TXP2 | bidirectional | Port 2 physical transmit (MDI) or receive (MDI-X) signal, positive differential. |
| 15 | FXSD2 | input | Fiber signal detect input for port 2 in 100BASE-FX mode; must be pulled to GND in copper mode and is available only on KSZ8463FML/FRL. |
| 16 | VDD_COL | power_in | Second low-voltage analog power input, to be filtered with a ferrite bead and capacitors. |
| 17 | PWRDN | input | Active-low full-chip power-down input; when asserted low all I/O are tri-stated and registers return to default. |
| 18 | X1 | input | 25 MHz crystal or oscillator clock connection with a required tolerance of ±50 ppm. |
| 19 | X2 | output | Second crystal connection; left as no connect when an oscillator drives X1. |
| 20 | DGND | power_in | Digital ground. |
| 21 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO logic and the internal low-voltage regulator. |
| 22 | TX_EN | input | In MII mode, active-high transmit enable indicating valid data on TXD[3:0]; in RMII mode, it indicates valid data on TXD[1:0]. |
| 23 | TXD3/EN_REFCLKO | input | In MII mode, transmit data bit 3 synchronous to TX_CLK; in RMII mode, pulling it up enables the 50 MHz REFCLK_O output on pin 32. |
| 24 | TXD2/NC | input | In MII mode, transmit data bit 2 synchronous to TX_CLK; in RMII mode it is not connected. |
| 25 | TXD1 | input | Transmit data bit 1, synchronous to TX_CLK in MII mode or to the 50 MHz REFCLK in RMII mode. |
| 26 | TXD0 | input | Transmit data bit 0, synchronous to TX_CLK in MII mode or to the 50 MHz REFCLK in RMII mode. |
| 27 | TX_CLK/REFCLK_I | bidirectional | In MII mode, transmit clock (2.5 MHz at 10BASE-T, 25 MHz at 100BASE-TX); in RMII mode, 50 MHz reference clock input. |
| 28 | TX_ER/MII_BP | input | In MII MAC mode, transmit error input; in MII PHY mode, 1 disables the PHY link and enables bypass mode. |
| 29 | DGND | power_in | Digital ground. |
| 30 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO logic and the internal low-voltage regulator. |
| 31 | RX_DV | bidirectional | In MII mode, receive data valid active high; during power-up/reset a pull-down selects MAC MII mode, otherwise PHY MII mode is selected. |
| 32 | RXD3/REFCLK_O | bidirectional | In MII mode, receive data bit 3 synchronous to RX_CLK; in RMII mode, 50 MHz REFCLK_O output when EN_REFCLKO is pulled up (16 mA drive). |
| 33 | RXD2 | bidirectional | In MII mode, receive data bit 2 synchronous to RX_CLK; at power-up/reset a pull-down selects low-speed SPI (up to 12.5 MHz) instead of high-speed SPI (up to 50 MHz). |
| 34 | RXD1 | bidirectional | Receive data bit 1 synchronous to RX_CLK in MII mode or REFCLK in RMII mode; at reset it, with RXD0, selects the serial bus mode (SPI slave default or MIIM). |
| 35 | RXD0 | bidirectional | Receive data bit 0 synchronous to RX_CLK in MII mode or REFCLK in RMII mode; at reset it, with RXD1, selects the serial bus mode. |
| 36 | CRS/GPIO9_RLI | bidirectional | In MII mode, carrier sense (output in PHY mode, input in MAC mode); in RMII mode it is GPIO9. |
| 37 | COL/GPIO10_RLI | bidirectional | In MII mode, collision detect (output in PHY mode, input in MAC mode); in RMII mode it is GPIO10. |
| 38 | RX_CLK/GPIO7_RLI | bidirectional | In MII mode, receive clock (2.5 MHz at 10BASE-T, 25 MHz at 100BASE-TX); in RMII mode it is GPIO7. |
| 39 | DGND | power_in | Digital ground. |
| 40 | VDD_L | power_in | Low-voltage core supply: input if the internal low-voltage regulator is not used, or regulated low-voltage output if it is used. |
| 41 | SPI_DO | bidirectional | Serial data output in SPI slave mode; at power-up/reset it selects 25 MHz from X1/X2 or 50 MHz from REFCLK_I and must NOT be pulled down on KSZ8463ML/FML. |
| 42 | SPI_CSN | input | Active-low SPI chip select in slave mode; requires an external 4.7 kΩ pull-up when in use. |
| 43 | INTRN | output | Active-low interrupt output to the host CPU; requires an external 4.7 kΩ pull-up resistor. |
| 44 | SPI_SCLK/MDC | input | Serial clock input in SPI slave mode, or MDC clock input in MIIM mode. |
| 45 | SPI_DI/MDIO | bidirectional | Serial data input in SPI slave mode, or MDIO data input/output in MIIM mode; requires an external 4.7 kΩ pull-up. |
| 46 | GPIO8 | bidirectional | General purpose I/O 8, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 47 | GPIO11 | bidirectional | General purpose I/O 11, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 48 | GPIO0 | bidirectional | General purpose I/O 0 usable as IEEE 1588 event trigger or time stamp input/output and directly driven or read by the host. |
| 49 | GPIO1 | bidirectional | General purpose I/O 1, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 50 | DGND | power_in | Digital ground. |
| 51 | VDD_L | power_in | Low-voltage core supply: input if the internal low-voltage regulator is not used, or regulated low-voltage output if it is used. |
| 52 | GPIO2 | bidirectional | General purpose I/O 2, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 53 | GPIO3 | bidirectional | General purpose I/O 3, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 54 | GPIO4 | bidirectional | General purpose I/O 4, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 55 | GPIO5 | bidirectional | General purpose I/O 5, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 56 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO logic and the internal low-voltage regulator. |
| 57 | DGND | power_in | Digital ground. |
| 58 | GPIO6 | bidirectional | General purpose I/O 6, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 59 | P1LED1/GPIO7_MLI | bidirectional | Programmable LED output for port 1 and port 2 activity/status, active (on) when low; alternately GPIO7 when IOMXSEL is set. |
| 60 | P1LED0 | bidirectional | Programmable LED output for port 1 status, active (on) when low, with function set by the SGCR7 indicator table. |
| 61 | P2LED1/GPIO9_MLI | bidirectional | Programmable LED output for port 2 activity/status, active (on) when low; alternately GPIO9 when IOMXSEL is set. |
| 62 | P2LED0/GPIO10_MLI | bidirectional | Programmable LED output for port 2 status, active (on) when low; alternately GPIO10 when IOMXSEL is set on the MII variant. |
| 63 | RSTN | input | Active-low hardware reset input that must be low for at least 10 ms after VDD_IO and 3.3V supplies are stable. |
| 64 | FXSD1 | input | Fiber signal detect input for port 1 in 100BASE-FX mode; must be pulled to GND in copper mode and is available only on KSZ8463FML/FRL. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | LQFP-64(10x10) |
| Category | Communication Interface Chip |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VDD_A3.3, VDD_IO) | -0.5 | 5 | V | 189 | |||
| Supply Voltage (VDD_AL, VDD_L) | -0.5 | 1.8 | V | 189 | |||
| Input Voltage (All Inputs) | -0.5 | 5 | V | 189 | |||
| Output Voltage (All Outputs) | -0.5 | 5 | V | 189 | |||
| Lead Temperature (soldering, 10s) | 260 | °C | soldering, 10s | 189 | |||
| Storage Temperature (TS) | TS | -65 | 150 | °C | 189 | ||
| Maximum Junction Temperature (TJ) | TJ | 125 | °C | 189 | |||
| HBM ESD Rating | 2 | kV | 189 | ||||
| Supply Voltage VDDA_3.3 | 3.135 | 3.465 | V | 189 | |||
| Supply Voltage VDD_L, VDD_AL, VDD_COL | 1.25 | 1.4 | V | 189 | |||
| Supply Voltage VDD_IO (3.3V) | 3.135 | 3.465 | V | 189 | |||
| Supply Voltage VDD_IO (2.5V) | 2.375 | 2.625 | V | 189 | |||
| Supply Voltage VDD_IO (1.8V) | 1.71 | 1.89 | V | 189 | |||
| Ambient Operating Temperature (TA) Industrial | TA | -40 | 85 | °C | Industrial | 189 | |
| Thermal Resistance Junction-to-Ambient | ΘJA | 49 | °C/W | Note 5-1: no heat spreader, air velocity 0 m/s | 189 | ||
| Thermal Resistance Junction-to-Case | ΘJC | 19 | °C/W | Note 5-1: no heat spreader, air velocity 0 m/s | 189 | ||
| CMOS Inputs Input Current | IIN | -10 | 10 | µA | VIN = GND ~ VDD_IO | 191 | |
| X1 Crystal/Osc Input Pin Input High Voltage | VIH | 2.1 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 | ||
| X1 Crystal/Osc Input Pin Input Low Voltage | VIL | 0.9 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 | ||
| X1 Crystal/Osc Input Pin Input Current | IIN | 10 | µA | 191 | |||
| PWRDN Input High Voltage | VIH | 1.1 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 | ||
| PWRDN Input Low Voltage | VIL | 0.3 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 | ||
| FXSD Input High Voltage | VIH | 2.1 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 192 | ||
| FXSD Input Low Voltage | VIL | 1.2 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 192 | ||
| Output Tri-State Leakage | /IOZ/ | 10 | µA | 192 | |||
| 100BASE-TX Peak Differential Output Voltage | VO | 0.95 | 1.05 | V | 100Ω termination on the diff. output | 192 | |
| 100BASE-TX Output Voltage Imbalance | VIMB | 2 | % | 100Ω termination on the diff. output | 192 | ||
| 100BASE-TX Rise/Fall Time | tr/tf | 3 | 5 | ns | 192 | ||
| 100BASE-TX Rise/Fall Time Imbalance | 0 | 0.5 | ns | 192 | |||
| 100BASE-TX Duty Cycle Distortion | -0.25 | 0.25 | ns | 192 | |||
| 100BASE-TX Overshoot | 5 | % | 192 | ||||
| 100BASE-TX Output Jitter | 0.7 | 1.4 | ns | Peak-to-peak | 192 | ||
| 10BASE-T Peak Differential Output Voltage | VP | 2.2 | 2.5 | 2.8 | V | 100Ω termination on the differential output | 192 |
| 10BASE-T Jitter Added | 1.8 | 3.5 | ns | 100Ω termination on the differential output (peak-to-peak) | 192 | ||
| 1.8V Pull-Up Resistance | R1.8PU | 57 | 100 | 187 | kΩ | VDD_IO = 1.8V | 192 |
| 1.8V Pull-Down Resistance | R1.8PD | 55 | 100 | 190 | kΩ | 192 | |
| 2.5V Pull-Up Resistance | R2.5PU | 37 | 59 | 102 | kΩ | VDD_IO = 2.5V | 192 |
| 2.5V Pull-Down Resistance | R2.5PD | 35 | 60 | 110 | kΩ | 192 | |
| 3.3V Pull-Up Resistance | R3.3PU | 29 | 43 | 70 | kΩ | VDD_IO = 3.3V | 192 |
| 3.3V Pull-Down Resistance | R3.3PD | 27 | 43 | 76 | kΩ | 192 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | In copper mode, and on the KSZ8463ML and KSZ8463RL, the FXSD pins are unused and should be pulled low. | 18 |
CAD (KiCad official)
- Symbol:
KSZ8463MLI - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
ksz8463mli-etched.step/ksz8463mli-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz8463mli.step/ksz8463mli.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (213 pp, sha256
6e2255020c924402, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# KSZ8463MLI
**Microchip Tech** · Interface - Specialized · LQFP-64(10x10)
KSZ8463MLI from Microchip Tech, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RXM1 | bidirectional | Port 1 physical receive (MDI) or transmit (MDI-X) signal, negative differential. |
| 2 | RXP1 | bidirectional | Port 1 physical receive (MDI) or transmit (MDI-X) signal, positive differential. |
| 3 | AGND | power_in | Analog ground. |
| 4 | TXM1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, negative differential. |
| 5 | TXP1 | bidirectional | Port 1 physical transmit (MDI) or receive (MDI-X) signal, positive differential. |
| 6 | VDD_AL | power_in | Filtered low-voltage analog power input, to be filtered with a ferrite bead and capacitors. |
| 7 | ISET | output | Sets the physical transmit output current; pull down with a 6.49 kΩ (1%) resistor to ground. |
| 8 | AGND | power_in | Analog ground. |
| 9 | VDD_A3.3 | power_in | 3.3V analog VDD input power supply, must be well decoupled. |
| 10 | RXM2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, negative differential. |
| 11 | RXP2 | bidirectional | Port 2 physical receive (MDI) or transmit (MDI-X) signal, positive differential. |
| 12 | AGND | power_in | Analog ground. |
| 13 | TXM2 | bidirectional | Port 2 physical transmit (MDI) or receive (MDI-X) signal, negative differential. |
| 14 | TXP2 | bidirectional | Port 2 physical transmit (MDI) or receive (MDI-X) signal, positive differential. |
| 15 | FXSD2 | input | Fiber signal detect input for port 2 in 100BASE-FX mode; must be pulled to GND in copper mode and is available only on KSZ8463FML/FRL. |
| 16 | VDD_COL | power_in | Second low-voltage analog power input, to be filtered with a ferrite bead and capacitors. |
| 17 | PWRDN | input | Active-low full-chip power-down input; when asserted low all I/O are tri-stated and registers return to default. |
| 18 | X1 | input | 25 MHz crystal or oscillator clock connection with a required tolerance of ±50 ppm. |
| 19 | X2 | output | Second crystal connection; left as no connect when an oscillator drives X1. |
| 20 | DGND | power_in | Digital ground. |
| 21 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO logic and the internal low-voltage regulator. |
| 22 | TX_EN | input | In MII mode, active-high transmit enable indicating valid data on TXD[3:0]; in RMII mode, it indicates valid data on TXD[1:0]. |
| 23 | TXD3/EN_REFCLKO | input | In MII mode, transmit data bit 3 synchronous to TX_CLK; in RMII mode, pulling it up enables the 50 MHz REFCLK_O output on pin 32. |
| 24 | TXD2/NC | input | In MII mode, transmit data bit 2 synchronous to TX_CLK; in RMII mode it is not connected. |
| 25 | TXD1 | input | Transmit data bit 1, synchronous to TX_CLK in MII mode or to the 50 MHz REFCLK in RMII mode. |
| 26 | TXD0 | input | Transmit data bit 0, synchronous to TX_CLK in MII mode or to the 50 MHz REFCLK in RMII mode. |
| 27 | TX_CLK/REFCLK_I | bidirectional | In MII mode, transmit clock (2.5 MHz at 10BASE-T, 25 MHz at 100BASE-TX); in RMII mode, 50 MHz reference clock input. |
| 28 | TX_ER/MII_BP | input | In MII MAC mode, transmit error input; in MII PHY mode, 1 disables the PHY link and enables bypass mode. |
| 29 | DGND | power_in | Digital ground. |
| 30 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO logic and the internal low-voltage regulator. |
| 31 | RX_DV | bidirectional | In MII mode, receive data valid active high; during power-up/reset a pull-down selects MAC MII mode, otherwise PHY MII mode is selected. |
| 32 | RXD3/REFCLK_O | bidirectional | In MII mode, receive data bit 3 synchronous to RX_CLK; in RMII mode, 50 MHz REFCLK_O output when EN_REFCLKO is pulled up (16 mA drive). |
| 33 | RXD2 | bidirectional | In MII mode, receive data bit 2 synchronous to RX_CLK; at power-up/reset a pull-down selects low-speed SPI (up to 12.5 MHz) instead of high-speed SPI (up to 50 MHz). |
| 34 | RXD1 | bidirectional | Receive data bit 1 synchronous to RX_CLK in MII mode or REFCLK in RMII mode; at reset it, with RXD0, selects the serial bus mode (SPI slave default or MIIM). |
| 35 | RXD0 | bidirectional | Receive data bit 0 synchronous to RX_CLK in MII mode or REFCLK in RMII mode; at reset it, with RXD1, selects the serial bus mode. |
| 36 | CRS/GPIO9_RLI | bidirectional | In MII mode, carrier sense (output in PHY mode, input in MAC mode); in RMII mode it is GPIO9. |
| 37 | COL/GPIO10_RLI | bidirectional | In MII mode, collision detect (output in PHY mode, input in MAC mode); in RMII mode it is GPIO10. |
| 38 | RX_CLK/GPIO7_RLI | bidirectional | In MII mode, receive clock (2.5 MHz at 10BASE-T, 25 MHz at 100BASE-TX); in RMII mode it is GPIO7. |
| 39 | DGND | power_in | Digital ground. |
| 40 | VDD_L | power_in | Low-voltage core supply: input if the internal low-voltage regulator is not used, or regulated low-voltage output if it is used. |
| 41 | SPI_DO | bidirectional | Serial data output in SPI slave mode; at power-up/reset it selects 25 MHz from X1/X2 or 50 MHz from REFCLK_I and must NOT be pulled down on KSZ8463ML/FML. |
| 42 | SPI_CSN | input | Active-low SPI chip select in slave mode; requires an external 4.7 kΩ pull-up when in use. |
| 43 | INTRN | output | Active-low interrupt output to the host CPU; requires an external 4.7 kΩ pull-up resistor. |
| 44 | SPI_SCLK/MDC | input | Serial clock input in SPI slave mode, or MDC clock input in MIIM mode. |
| 45 | SPI_DI/MDIO | bidirectional | Serial data input in SPI slave mode, or MDIO data input/output in MIIM mode; requires an external 4.7 kΩ pull-up. |
| 46 | GPIO8 | bidirectional | General purpose I/O 8, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 47 | GPIO11 | bidirectional | General purpose I/O 11, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 48 | GPIO0 | bidirectional | General purpose I/O 0 usable as IEEE 1588 event trigger or time stamp input/output and directly driven or read by the host. |
| 49 | GPIO1 | bidirectional | General purpose I/O 1, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 50 | DGND | power_in | Digital ground. |
| 51 | VDD_L | power_in | Low-voltage core supply: input if the internal low-voltage regulator is not used, or regulated low-voltage output if it is used. |
| 52 | GPIO2 | bidirectional | General purpose I/O 2, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 53 | GPIO3 | bidirectional | General purpose I/O 3, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 54 | GPIO4 | bidirectional | General purpose I/O 4, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 55 | GPIO5 | bidirectional | General purpose I/O 5, with pull-down, usable for IEEE 1588 event trigger and time stamp functions. |
| 56 | VDD_IO | power_in | 3.3V, 2.5V, or 1.8V digital VDD input for IO logic and the internal low-voltage regulator. |
| 57 | DGND | power_in | Digital ground. |
| 58 | GPIO6 | bidirectional | General purpose I/O 6, with pull-up, usable for IEEE 1588 event trigger and time stamp functions. |
| 59 | P1LED1/GPIO7_MLI | bidirectional | Programmable LED output for port 1 and port 2 activity/status, active (on) when low; alternately GPIO7 when IOMXSEL is set. |
| 60 | P1LED0 | bidirectional | Programmable LED output for port 1 status, active (on) when low, with function set by the SGCR7 indicator table. |
| 61 | P2LED1/GPIO9_MLI | bidirectional | Programmable LED output for port 2 activity/status, active (on) when low; alternately GPIO9 when IOMXSEL is set. |
| 62 | P2LED0/GPIO10_MLI | bidirectional | Programmable LED output for port 2 status, active (on) when low; alternately GPIO10 when IOMXSEL is set on the MII variant. |
| 63 | RSTN | input | Active-low hardware reset input that must be low for at least 10 ms after VDD_IO and 3.3V supplies are stable. |
| 64 | FXSD1 | input | Fiber signal detect input for port 1 in 100BASE-FX mode; must be pulled to GND in copper mode and is available only on KSZ8463FML/FRL. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | LQFP-64(10x10) |
| Category | Communication Interface Chip |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VDD_A3.3, VDD_IO) | | -0.5 | | 5 | V | | 189 |
| Supply Voltage (VDD_AL, VDD_L) | | -0.5 | | 1.8 | V | | 189 |
| Input Voltage (All Inputs) | | -0.5 | | 5 | V | | 189 |
| Output Voltage (All Outputs) | | -0.5 | | 5 | V | | 189 |
| Lead Temperature (soldering, 10s) | | | | 260 | °C | soldering, 10s | 189 |
| Storage Temperature (TS) | TS | -65 | | 150 | °C | | 189 |
| Maximum Junction Temperature (TJ) | TJ | | | 125 | °C | | 189 |
| HBM ESD Rating | | | | 2 | kV | | 189 |
| Supply Voltage VDDA_3.3 | | 3.135 | | 3.465 | V | | 189 |
| Supply Voltage VDD_L, VDD_AL, VDD_COL | | 1.25 | | 1.4 | V | | 189 |
| Supply Voltage VDD_IO (3.3V) | | 3.135 | | 3.465 | V | | 189 |
| Supply Voltage VDD_IO (2.5V) | | 2.375 | | 2.625 | V | | 189 |
| Supply Voltage VDD_IO (1.8V) | | 1.71 | | 1.89 | V | | 189 |
| Ambient Operating Temperature (TA) Industrial | TA | -40 | | 85 | °C | Industrial | 189 |
| Thermal Resistance Junction-to-Ambient | ΘJA | | 49 | | °C/W | Note 5-1: no heat spreader, air velocity 0 m/s | 189 |
| Thermal Resistance Junction-to-Case | ΘJC | | 19 | | °C/W | Note 5-1: no heat spreader, air velocity 0 m/s | 189 |
| CMOS Inputs Input Current | IIN | -10 | | 10 | µA | VIN = GND ~ VDD_IO | 191 |
| X1 Crystal/Osc Input Pin Input High Voltage | VIH | 2.1 | | | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 |
| X1 Crystal/Osc Input Pin Input Low Voltage | VIL | | | 0.9 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 |
| X1 Crystal/Osc Input Pin Input Current | IIN | | | 10 | µA | | 191 |
| PWRDN Input High Voltage | VIH | 1.1 | | | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 |
| PWRDN Input Low Voltage | VIL | | | 0.3 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 191 |
| FXSD Input High Voltage | VIH | 2.1 | | | V | VDD_A3.3 = 3.3V, VDD_IO = any | 192 |
| FXSD Input Low Voltage | VIL | | | 1.2 | V | VDD_A3.3 = 3.3V, VDD_IO = any | 192 |
| Output Tri-State Leakage | /IOZ/ | | | 10 | µA | | 192 |
| 100BASE-TX Peak Differential Output Voltage | VO | 0.95 | | 1.05 | V | 100Ω termination on the diff. output | 192 |
| 100BASE-TX Output Voltage Imbalance | VIMB | | | 2 | % | 100Ω termination on the diff. output | 192 |
| 100BASE-TX Rise/Fall Time | tr/tf | 3 | | 5 | ns | | 192 |
| 100BASE-TX Rise/Fall Time Imbalance | | | 0 | 0.5 | ns | | 192 |
| 100BASE-TX Duty Cycle Distortion | | -0.25 | | 0.25 | ns | | 192 |
| 100BASE-TX Overshoot | | | | 5 | % | | 192 |
| 100BASE-TX Output Jitter | | | 0.7 | 1.4 | ns | Peak-to-peak | 192 |
| 10BASE-T Peak Differential Output Voltage | VP | 2.2 | 2.5 | 2.8 | V | 100Ω termination on the differential output | 192 |
| 10BASE-T Jitter Added | | | 1.8 | 3.5 | ns | 100Ω termination on the differential output (peak-to-peak) | 192 |
| 1.8V Pull-Up Resistance | R1.8PU | 57 | 100 | 187 | kΩ | VDD_IO = 1.8V | 192 |
| 1.8V Pull-Down Resistance | R1.8PD | 55 | 100 | 190 | kΩ | | 192 |
| 2.5V Pull-Up Resistance | R2.5PU | 37 | 59 | 102 | kΩ | VDD_IO = 2.5V | 192 |
| 2.5V Pull-Down Resistance | R2.5PD | 35 | 60 | 110 | kΩ | | 192 |
| 3.3V Pull-Up Resistance | R3.3PU | 29 | 43 | 70 | kΩ | VDD_IO = 3.3V | 192 |
| 3.3V Pull-Down Resistance | R3.3PD | 27 | 43 | 76 | kΩ | | 192 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | In copper mode, and on the KSZ8463ML and KSZ8463RL, the FXSD pins are unused and should be pulled low. | 18 |
## CAD (KiCad official)
- Symbol: `KSZ8463MLI`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `ksz8463mli-etched.step` / `ksz8463mli-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ksz8463mli.step` / `ksz8463mli.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/ksz8463mli-datasheet.pdf) (213 pp, sha256 `6e2255020c924402`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ksz8463mli-datasheet.pdf)