3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownKSZ8001LI
Microchip Tech · Ethernet Transceivers · LQFP-48(7x7)
KSZ8001LI from Microchip Tech, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MDIO | bidirectional | MII Management (MIIM) interface data I/O; this pin requires an external 4.7K pull-up resistor. |
| 2 | MDC | input | MII Management (MIIM) interface clock input, synchronous to the MDIO data line. |
| 3 | RXD3/PHYAD1 | bidirectional | In MII mode this is receive data output bit 3, synchronous with RXC; during reset the pull-up/pull-down is latched as PHYAD[1]. |
| 4 | RXD2/PHYAD2 | bidirectional | In MII mode this is receive data output bit 2, synchronous with RXC; during reset the pull-up/pull-down is latched as PHYAD[2]. |
| 5 | RXD1/RXD[1]/PHYAD3 | bidirectional | Receive data output bit 1 in MII and RMII modes; during reset the pull-up/pull-down is latched as PHYAD[3]. |
| 6 | RXD0/RXD[0]/PHYAD4 | bidirectional | Receive data output bit 0 in MII and RMII modes, and receive data and control in SMII mode; during reset the pull-up/pull-down is latched as PHYAD[4]. |
| 7 | VDDIO | power_in | 3.3V digital VDD supply. |
| 8 | GND | power_in | Ground. |
| 9 | RXDV/CRSDV/PCS_LPBK | bidirectional | Receive data valid output in MII mode and carrier sense/receive data valid in RMII mode; during reset the pull-up/pull-down is latched as PCS_LPBK. |
| 10 | RXC/SMII_SELECT | bidirectional | MII receive clock output at 25 MHz for 100 Mbps and 2.5 MHz for 10 Mbps; during reset the pull-up/pull-down is latched as SMII select. |
| 11 | RXER/RX_ER/ISO | bidirectional | Receive error output in MII and RMII modes; during reset the pull-up/pull-down is latched as ISOLATE. |
| 12 | GND | power_in | Ground. |
| 13 | VDDC | power_in | 1.8V digital core VDD; it is an output on the KSZ8001L and KSZ8001SL and an input on the KSZ8001S. |
| 14 | TXER | input | MII transmit error input; when asserted the KSZ8001 drives H symbols onto the line to force signaling errors. |
| 15 | TXC/REF_CLK/CLOCK | bidirectional | MII transmit clock output, 50 MHz reference clock input in RMII mode, or 125 MHz synchronization clock input in SMII mode. |
| 16 | TXEN | input | MII transmit enable input; the MAC asserts it with the first nibble of the preamble and de-asserts it after the last bit of the packet. |
| 17 | TXD0/TXD[0]/TX | input | Transmit data input bit 0 in MII and RMII modes, and transmit data and control in SMII mode. |
| 18 | TXD1/TXD[1]/SYNC | input | Transmit data input bit 1 in MII and RMII modes, and SYNC in SMII mode. |
| 19 | TXD2 | input | MII transmit data input bit 2, synchronous with TXC. |
| 20 | TXD3 | input | MII transmit data input bit 3, synchronous with TXC. |
| 21 | COL/RMII_SELECT | bidirectional | MII collision detect output; during reset the pull-up/pull-down is latched as RMII select. |
| 22 | CRS/RMII_BTB | bidirectional | MII carrier sense output; when RMII mode is selected, the pull-up/pull-down is latched as RMII loop-back during reset. |
| 23 | GND | power_in | Ground. |
| 24 | VDDIO | power_in | 3.3V digital VDD supply. |
| 25 | INT#/PHYAD0 | bidirectional | Management interface interrupt output; latched as PHYAD[0] during power-up or reset. |
| 26 | LED0/TEST | bidirectional | Programmable active-low LED output 0 that shows link and activity; an external pull-down enables factory test mode. |
| 27 | LED1/SPD100/noFEF | bidirectional | Programmable active-low LED output 1 that shows speed; latched as register 0h bit 13 speed setting during power-up or reset. |
| 28 | LED2/DUPLEX | bidirectional | Programmable active-low LED output 2 that shows duplex; latched as register 0h bit 8 duplex setting during power-up or reset. |
| 29 | LED3/NWAYEN | bidirectional | Programmable active-low LED output 3 that shows collision or activity; latched as register 0h bit 12 auto-negotiation enable during power-up or reset. |
| 30 | PD# | input | Chip power-down input, active low: high for normal operation and low for power-down mode. |
| 31 | VDDRX | power_in | 1.8V analog VDD supply. |
| 32 | RX- | bidirectional | Physical receive or transmit '-' differential signal. |
| 33 | RX+ | bidirectional | Physical receive or transmit '+' differential signal. |
| 34 | FXSD/FXEN | bidirectional | Fiber mode enable and signal detect in fiber mode; FX mode is disabled when FXEN is 0, with the default set to 0. |
| 35 | GND | power_in | Ground. |
| 36 | GND | power_in | Ground. |
| 37 | REXT | input | Connect a 6.65K external resistor from this pin to ground. |
| 38 | VDDRCV | power_in | 3.3V analog VDD supply. |
| 39 | GND | power_in | Ground. |
| 40 | TX- | bidirectional | Physical transmit or receive '-' differential signal. |
| 41 | TX+ | bidirectional | Physical transmit or receive '+' differential signal. |
| 42 | NC | unconnected | No connect. |
| 43 | NC | unconnected | No connect. |
| 44 | GND | power_in | Ground. |
| 45 | XO | output | 25 MHz crystal or oscillator clock connection; it is a no connect when an oscillator drives XI, with clock tolerance of +/- 50 ppm. |
| 46 | XI | input | 25 MHz crystal or oscillator clock connection; when an oscillator is used it connects to a 3.3V tolerant oscillator, with clock tolerance of +/- 50 ppm. |
| 47 | VDDPLL | power_in | 1.8V analog PLL VDD supply. |
| 48 | RST# | input | Chip reset, active low; a minimum pulse of 50 us is required. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | LQFP-48(7x7) |
| Category | Communication Interface Chip |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TS | -55 | 150 | °C | 34 | ||
| Supply Voltage referenced to GND | -0.5 | 4 | V | 34 | |||
| All pins voltage | -0.5 | 4 | V | 34 | |||
| Ambient Temperature Industrial (TAI) | TAI | -40 | 85 | °C | Industrial grade (KSZ8001LI) | 34 | |
| Supply Voltage (VDDPLL, VDDRX, VDDC) | VDDPLL, VDDRX, VDDC | 1.8 | V | 34 | |||
| Supply Voltage tolerance (VDDPLL, VDDRX, VDDC) | VDDPLL, VDDRX, VDDC | -5 | 5 | % | 34 | ||
| Supply Voltage (VDDRCV, VDDIO) | VDDRCV, VDDIO | 3.3 | V | 34 | |||
| Supply Voltage tolerance (VDDRCV, VDDIO) | VDDRCV, VDDIO | -5 | 5 | % | 34 | ||
| Package Thermal Resistance JA | JA | 83.56 | Airflow 0 m/s, KSZ8001L / KSZ8001LI | 34 | |||
| Package Thermal Resistance JA | JA | 77.08 | Airflow 1 m/s, KSZ8001L / KSZ8001LI | 34 | |||
| Package Thermal Resistance JA | JA | 72.36 | Airflow 2 m/s, KSZ8001L / KSZ8001LI | 34 | |||
| Package Thermal Resistance JC | JC | 35.9 | Airflow 0 m/s, KSZ8001L / KSZ8001LI | 34 | |||
| TTL Input High Voltage | VIH | 2 | V | 34 | |||
| TTL Input Low Voltage | VIL | 0.8 | V | 34 | |||
| TTL Output High Voltage | VOH | 2.4 | V | IOH = -4mA | 34 | ||
| TTL Output Low Voltage | VOL | 0.4 | V | 34 | |||
| Input Current | IIN | -10 | 10 | uA | VIN = GND - VDD | 34 | |
| Total Supply Current 100BASE-TX | IDD1 | 52 | mA | Chip only, no transformer | 34 | ||
| Total Supply Current 10BASE-T | IDD2 | 32 | mA | Chip only, no transformer | 34 | ||
| Total Supply Current Power Saving Mode | IDD3 | 35 | mA | Ethernet cable disconnected | 34 | ||
| Total Supply Current SW Power Down Mode | IDD4 | 5 | mA | Register (software) power down | 34 | ||
| Total Supply Current Power down pin (PD#) | IDD5 | 3 | mA | Chip (hardware) power down | 34 | ||
| 100BASE-TX Peak Differential Output Voltage | VO | 0.95 | 1.05 | V | 50 from each output to VDD | 35 | |
| 100BASE-TX Output Voltage Imbalance | VIMB | 2 | % | 50 from each output to VDD | 35 | ||
| 100BASE-TX Overshoot | 5 | % | 35 | ||||
| 10BASE-T Peak Differential Output Voltage | VP | 2.2 | 2.8 | V | 50 from each output to VDD | 35 | |
| REXT external resistor | REXT | 6.65 | K | External resistor from REXT pin to ground | 9 | ||
| REXT resistor tolerance | REXT | -1 | 1 | % | 1% external resistor | 12 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | do this, RXD2 and TXD2 pins need to be connected via an inverter. When TXD2 pin is high in both the copper and fiber | 23 |
CAD (KiCad official)
- Symbol:
KSZ8001LI - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
ksz8001li-etched.step/ksz8001li-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ksz8001li.step/ksz8001li.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (51 pp, sha256
1203273bca1b850f, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).