main
Ray Publish 0.1.0 37dd153

ISO5852SQDWRQ1

Texas Instruments · Gate Drive ICs · SOIC-16-300mil

ISO5852SQDWRQ1 from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VEE2 power_in Output negative supply; connect to GND2 for unipolar supply application.
2 DESAT input Desaturation voltage input for IGBT collector-emitter overcurrent detection, referenced to GND2.
3 GND2 power_in Gate drive common; connect to IGBT emitter.
4 OUTH output Positive gate drive voltage output (2.5-A peak source).
5 VCC2 power_in Most positive output supply potential, 15 V to 30 V with respect to GND2.
6 OUTL output Negative gate drive voltage output (5-A peak sink).
7 CLAMP output Miller clamp output, used to sink Miller current from the IGBT gate when the gate is turned off in unipolar operation.
8 VEE2 power_in Output negative supply; connect to GND2 for unipolar supply application.
9 GND1 power_in Input ground.
10 IN+ input Non-inverting gate drive voltage control input, CMOS compatible with thresholds referenced to VCC1.
11 IN- input Inverting gate drive voltage control input, CMOS compatible with thresholds referenced to VCC1.
12 RDY output Power-good output, high when both input-side and output-side supplies are good; open-drain with internal 50-kΩ pullup.
13 FLT output Fault output, active low during DESAT condition; latched until reset through RST after RDY goes high.
14 RST input Reset input; apply a low pulse of at least 800 ns to reset the fault latch.
15 VCC1 power_in Positive input supply, 2.25 V to 5.5 V.
16 GND1 power_in Input ground.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-16-300mil
Category Power Supply Chip
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC1 supply-voltage input side VCC1 -0.3 6 V referenced to GND1 4
Positive supply-voltage output side (VCC2, GND2) VCC2 -0.3 35 V 4
Negative supply-voltage output side (VEE2, GND2) VEE2 -17.5 0.3 V referenced to GND2 4
Total-supply output voltage (VCC2, VEE2) V(SUP2) -0.3 35 V 4
Gate-driver high output current I(OUTH) 2.7 A Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% 4
Gate-driver low output current I(OUTL) 5.5 A Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% 4
Output current of FLT, RDY I(LOP) 10 mA 4
Junction temperature TJ -40 150 °C 4
Storage temperature TSTG -65 150 °C 4
Supply-voltage input side (VCC1, GND1) VCC1 2.25 5.5 V 4
Positive supply-voltage output side (VCC2, GND2) VCC2 15 30 V 4
Negative supply-voltage output side (VEE2, GND2) V(EE2) -15 0 V 4
Total supply-voltage output side (VCC2, VEE2) V(SUP2) 15 30 V 4
Pulse width at IN+, IN- for full output tUI 40 ns CLOAD = 1 nF 4
Pulse width at RST for resetting fault latch tRST 800 ns 4
Ambient temperature TA -40 125 °C 4
Junction-to-ambient thermal resistance RθJA 99.6 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 48.5 °C/W 5
Junction-to-board thermal resistance RθJB 56.5 °C/W 5
Junction-to-top characterization parameter ψJT 29.2 °C/W 5
Junction-to-board characterization parameter ψJB 56.5 °C/W 5
Maximum power dissipation (both sides) PD 1255 mW VCC1 = 5.5 V, VCC2 = 30 V, TA = 25°C 5
Maximum input power dissipation PID 175 mW VCC1 = 5.5 V, VCC2 = 30 V, TA = 25°C 5
Maximum output power dissipation POD 1080 mW VCC1 = 5.5 V, VCC2 = 30 V, TA = 25°C 5
Input-supply quiescent current IQ1 2.8 4.5 mA 8
Output-supply quiescent current IQ2 3.6 6 mA 8
Low-level clamp current I(CLP) 1.6 2.5 3.3 A V(CLAMP) = VEE2 + 2.5 V 8
Clamp threshold voltage V(CLTH) 1.6 2.1 2.5 V 8
Blanking-capacitor charge current I(CHG) 0.42 0.5 0.58 mA V(DESAT), GND2 = 2 V 8
DESAT threshold voltage with respect to GND2 V(DSTH) 8.3 9 9.5 V 9
Output-signal rise time at OUTH tr 12 18 35 ns CLOAD = 1 nF 9
Output-signal fall time at OUTL tf 12 20 37 ns CLOAD = 1 nF 9
Propagation delay tPLH, tPHL 76 110 ns CLOAD = 1 nF 9
Glitch filter on IN+, IN-, RST tGF (IN,/RST) 20 30 40 ns CLOAD = 1 nF 9
Leading-edge blanking time tLEB 310 400 480 ns See Figure 44 and Figure 45 9
Common-mode transient immunity CMTI 100 120 kV/μs VCM = 1500 V, see Figure 47 9

CAD (KiCad official)

  • Symbol: ISO5852SQDWRQ1
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: iso5852sqdwrq1-etched.step / iso5852sqdwrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); iso5852sqdwrq1.step / iso5852sqdwrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (40 pp, sha256 318e69c0fd223ff4, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF