main
Ray
Publish 0.1.0
1e28758
ISO5852SMDWREP
Texas Instruments · Gate Drive ICs · SOIC-16-300mil
ISO5852SMDWREP from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE2 | power_in | Output negative supply; connect to GND2 for unipolar supply applications. |
| 2 | DESAT | input | Desaturation voltage input used to detect IGBT collector-emitter overvoltage during short-circuit events; absolute voltage limited to GND2 - 0.3 V to VCC2 + 0.3 V. |
| 3 | GND2 | power_in | Gate drive common; connect to the IGBT emitter. |
| 4 | OUTH | output | Positive gate drive voltage output (2.5 A source capability). |
| 5 | VCC2 | power_in | Most positive output supply potential; 15 V to 30 V recommended with respect to GND2. |
| 6 | OUTL | output | Negative gate drive voltage output (5 A sink capability). |
| 7 | CLAMP | output | Miller clamp output that sinks Miller current from the IGBT gate (up to 2 A) when the gate voltage is below 2 V in unipolar operation. |
| 8 | VEE2 | power_in | Output negative supply; connect to GND2 for unipolar supply applications. |
| 9 | GND1 | power_in | Input ground. |
| 10 | IN+ | input | Non-inverting gate drive voltage control input; CMOS-compatible with high-level input at 0.7 × VCC1 minimum and low-level input at 0.3 × VCC1 maximum. |
| 11 | IN- | input | Inverting gate drive voltage control input; CMOS-compatible with high-level input at 0.7 × VCC1 minimum and low-level input at 0.3 × VCC1 maximum. |
| 12 | RDY | output | Power-good output that is high only when both the input and output supplies are above their UVLO thresholds; maximum output current 10 mA. |
| 13 | FLT | output | Fault output, active-low during a DESAT condition; latched and reset only through RST after RDY goes high; maximum output current 10 mA. |
| 14 | RST | input | Reset input; apply a low pulse of at least 800 ns to reset the fault latch. |
| 15 | VCC1 | power_in | Positive input supply, 2.25 V to 5.5 V. |
| 16 | GND1 | power_in | Input ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16-300mil |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC1 Supply-voltage input side | VCC1 | 2.25 | 5.5 | V | 5 | ||
| VCC2 Positive supply-voltage output side (VCC2 - GND2) | VCC2 | 15 | 30 | V | 5 | ||
| VEE2 Negative supply-voltage output side (VEE2 - GND2) | V(EE2) | -15 | 0 | V | 5 | ||
| Total supply-voltage output side (VCC2 - VEE2) | V(SUP2) | 15 | 30 | V | 5 | ||
| Pulse width at IN+, IN- for full output | tUI | 40 | ns | CLOAD = 1 nF | 5 | ||
| Pulse width at RST for resetting fault latch | tRST | 800 | ns | 5 | |||
| Ambient temperature | TA | -55 | 125 | °C | 5 | ||
| VCC1 Supply-voltage input side | VCC1 | 6 | V | 5 | |||
| VCC2 Positive supply-voltage output side (VCC2 - GND2) | VCC2 | -0.3 | 35 | V | 5 | ||
| VEE2 Negative supply-voltage output side (VEE2 - GND2) | VEE2 | -17.5 | 0.3 | V | 5 | ||
| Total-supply output voltage (VCC2 - VEE2) | V(SUP2) | -0.3 | 35 | V | 5 | ||
| Gate-driver high output current | I(OUTH) | 2.7 | A | Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% | 5 | ||
| Gate-driver low output current | I(OUTL) | 5.5 | A | Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% | 5 | ||
| Output current of FLT, RDY | I(LOP) | 10 | mA | 5 | |||
| Junction temperature | TJ | -55 | 150 | °C | 5 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 5 | ||
| Positive-going UVLO2 threshold-voltage output side | VIT+(UVLO2) | 12 | 13 | V | 9 | ||
| Negative-going UVLO2 threshold-voltage output side | VIT-(UVLO2) | 9.5 | 11 | V | 9 | ||
| Input-supply quiescent current | IQ1 | 2.8 | 4.5 | mA | 9 | ||
| Output-supply quiescent current | IQ2 | 3.6 | 6 | mA | 9 | ||
| High-level output peak current | I(OUTH) | 1.5 | 2.5 | A | IN+ = high, IN- = low, V(OUTH) = VCC2 - 15 V | 9 | |
| Low-level output peak current | I(OUTL) | 3.4 | 5 | A | IN+ = low, IN- = high, V(OUTL) = VEE2 + 15 V | 9 | |
| Low-level clamp current | I(CLP) | 1.6 | 2.5 | 3.3 | A | V(CLAMP) = VEE2 + 2.5 V | 9 |
| Clamp threshold voltage | V(CLTH) | 1.6 | 2.1 | 2.5 | V | 9 | |
| Clamping voltage (VOUTH - VCC2) | V(CLP-OUTH) | 1.1 | 1.3 | V | IN+ = high, IN- = low, tCLP = 10 µs, I(OUTH) = 500 mA | 9 | |
| Clamping voltage (VOUTL - VCC2) | V(CLP-OUTL) | 1.3 | 1.5 | V | IN+ = high, IN- = low, tCLP = 10 µs, I(OUTL) = 500 mA | 9 | |
| Clamping voltage at CLAMP | V(CLP-CLAMP) | 0.7 | 1.1 | V | IN+ = High, IN- = Low, I(CLP) = 20 mA | 9 | |
| Clamping voltage at OUTL (VCLP - VCC2) | V(CLP-OUTL) | 0.7 | 1.1 | V | IN+ = High, IN- = Low, I(OUTL) = 20 mA | 9 | |
| Blanking-capacitor charge current | I(CHG) | 0.42 | 0.5 | 0.58 | mA | V(DESAT) - GND2 = 2 V | 9 |
| Blanking-capacitor discharge current | I(DCHG) | 9 | 14 | mA | V(DESAT) - GND2 = 6 V | 9 | |
| DESAT threshold voltage with respect to GND2 | V(DSTH) | 8.3 | 9 | 9.5 | V | 10 | |
| DESAT voltage with respect to GND2 | V(DSL) | 0.4 | 1 | V | when OUTH or OUTL is driven low | 10 | |
| Output-signal rise time at OUTH | tr | 12 | 18 | 35 | ns | CLOAD = 1 nF; See Figure 44, Figure 45, and Figure 46 | 10 |
| Output-signal fall time at OUTL | tf | 12 | 20 | 37 | ns | CLOAD = 1 nF | 10 |
| Propagation delay | tPLH, tPHL | 76 | 110 | ns | CLOAD = 1 nF | 10 | |
| Glitch filter on IN+, IN-, RST | tGF (IN,/RST) | 20 | 30 | 40 | ns | CLOAD = 1 nF | 10 |
| DESAT sense to 90% VOUTH/L delay | tDS (90%) | 553 | 760 | ns | CLOAD = 10 nF | 10 | |
| DESAT sense to 10% VOUTH/L delay | tDS (10%) | 2 | 3.5 | μs | CLOAD = 10 nF | 10 | |
| Leading-edge blanking time | tLEB | 310 | 400 | 480 | ns | See Figure 44 and Figure 45 | 10 |
| Glitch filter on RST for resetting FLT | tGF(RSTFLT) | 300 | 800 | ns | 10 | ||
| Common-mode transient immunity | CMTI | 100 | 120 | kV/μs | VCM = 1500 V, see Figure 47 | 10 | |
| Positive-going UVLO1 threshold-voltage input side | VIT+(UVLO1) | 2.25 | V | 9 | |||
| Negative-going UVLO1 threshold-voltage input side | VIT-(UVLO1) | 1.7 | V | 9 | |||
| UVLO1 hysteresis voltage (VIT+ - VIT-) input side | VHYS(UVLO1) | 0.2 | V | 9 | |||
| UVLO2 hysteresis voltage (VIT+ - VIT-) output side | VHYS(UVLO2) | 1 | V | 9 | |||
| High-level input leakage at IN+ | IIH | 100 | µA | IN+ = VCC1 | 9 | ||
| Low-level input leakage at IN-, RST | IIL | -100 | µA | IN- = GND1, RST = GND1 | 9 | ||
| Pullup current of FLT, RDY | IPU | 100 | µA | V(RDY) = GND1, V(FLT) = GND1 | 9 | ||
| Low-level output voltage at FLT, RDY | V(OL) | 0.2 | V | I(FLT) = 5 mA | 9 | ||
| Active output pulldown voltage | V(OUTPD) | 2 | V | I(OUTH/L) = 200 mA, VCC2 = open | 9 | ||
| Low-level output current during fault condition | I(OLF) | 130 | mA | 9 | |||
| Clamping voltage (VCLP - VCC2) | V(CLP-CLP) | 1.3 | V | IN+ = high, IN- = low, tCLP = 10 µs, I(CLP) = 500 mA | 9 | ||
| Pulse skew /tPHL - tPLH/ | tsk-p | 20 | ns | CLOAD = 1 nF | 10 | ||
| DESAT-glitch filter delay | tDS (GF) | 330 | ns | CLOAD = 1 nF | 10 | ||
| DESAT sense to FLT-low delay | tDS (FLT) | 1.4 | μs | See Figure 46 | 10 | ||
| Input capacitance | CI | 2 | pF | VI = VCC1 / 2 + 0.4 × sin (2πft), f = 1 MHz, VCC1 = 5 V | 10 | ||
| Junction-to-ambient thermal resistance | RθJA | 99.6 | °C/W | 6 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 48.5 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 56.5 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
ISO5852SMDWREP - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
iso5852smdwrep-etched.step/iso5852smdwrep-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);iso5852smdwrep.step/iso5852smdwrep.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
b5e8ab9182fe12c2, retrieved 2026-11-12, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ISO5852SMDWREP
**Texas Instruments** · Gate Drive ICs · SOIC-16-300mil
ISO5852SMDWREP from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE2 | power_in | Output negative supply; connect to GND2 for unipolar supply applications. |
| 2 | DESAT | input | Desaturation voltage input used to detect IGBT collector-emitter overvoltage during short-circuit events; absolute voltage limited to GND2 - 0.3 V to VCC2 + 0.3 V. |
| 3 | GND2 | power_in | Gate drive common; connect to the IGBT emitter. |
| 4 | OUTH | output | Positive gate drive voltage output (2.5 A source capability). |
| 5 | VCC2 | power_in | Most positive output supply potential; 15 V to 30 V recommended with respect to GND2. |
| 6 | OUTL | output | Negative gate drive voltage output (5 A sink capability). |
| 7 | CLAMP | output | Miller clamp output that sinks Miller current from the IGBT gate (up to 2 A) when the gate voltage is below 2 V in unipolar operation. |
| 8 | VEE2 | power_in | Output negative supply; connect to GND2 for unipolar supply applications. |
| 9 | GND1 | power_in | Input ground. |
| 10 | IN+ | input | Non-inverting gate drive voltage control input; CMOS-compatible with high-level input at 0.7 × VCC1 minimum and low-level input at 0.3 × VCC1 maximum. |
| 11 | IN- | input | Inverting gate drive voltage control input; CMOS-compatible with high-level input at 0.7 × VCC1 minimum and low-level input at 0.3 × VCC1 maximum. |
| 12 | RDY | output | Power-good output that is high only when both the input and output supplies are above their UVLO thresholds; maximum output current 10 mA. |
| 13 | FLT | output | Fault output, active-low during a DESAT condition; latched and reset only through RST after RDY goes high; maximum output current 10 mA. |
| 14 | RST | input | Reset input; apply a low pulse of at least 800 ns to reset the fault latch. |
| 15 | VCC1 | power_in | Positive input supply, 2.25 V to 5.5 V. |
| 16 | GND1 | power_in | Input ground. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16-300mil |
| Category | Power Supply Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC1 Supply-voltage input side | VCC1 | 2.25 | | 5.5 | V | | 5 |
| VCC2 Positive supply-voltage output side (VCC2 - GND2) | VCC2 | 15 | | 30 | V | | 5 |
| VEE2 Negative supply-voltage output side (VEE2 - GND2) | V(EE2) | -15 | | 0 | V | | 5 |
| Total supply-voltage output side (VCC2 - VEE2) | V(SUP2) | 15 | | 30 | V | | 5 |
| Pulse width at IN+, IN- for full output | tUI | 40 | | | ns | CLOAD = 1 nF | 5 |
| Pulse width at RST for resetting fault latch | tRST | 800 | | | ns | | 5 |
| Ambient temperature | TA | -55 | | 125 | °C | | 5 |
| VCC1 Supply-voltage input side | VCC1 | | | 6 | V | | 5 |
| VCC2 Positive supply-voltage output side (VCC2 - GND2) | VCC2 | -0.3 | | 35 | V | | 5 |
| VEE2 Negative supply-voltage output side (VEE2 - GND2) | VEE2 | -17.5 | | 0.3 | V | | 5 |
| Total-supply output voltage (VCC2 - VEE2) | V(SUP2) | -0.3 | | 35 | V | | 5 |
| Gate-driver high output current | I(OUTH) | | | 2.7 | A | Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% | 5 |
| Gate-driver low output current | I(OUTL) | | | 5.5 | A | Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% | 5 |
| Output current of FLT, RDY | I(LOP) | | | 10 | mA | | 5 |
| Junction temperature | TJ | -55 | | 150 | °C | | 5 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 5 |
| Positive-going UVLO2 threshold-voltage output side | VIT+(UVLO2) | 12 | | 13 | V | | 9 |
| Negative-going UVLO2 threshold-voltage output side | VIT-(UVLO2) | 9.5 | | 11 | V | | 9 |
| Input-supply quiescent current | IQ1 | 2.8 | | 4.5 | mA | | 9 |
| Output-supply quiescent current | IQ2 | 3.6 | | 6 | mA | | 9 |
| High-level output peak current | I(OUTH) | 1.5 | | 2.5 | A | IN+ = high, IN- = low, V(OUTH) = VCC2 - 15 V | 9 |
| Low-level output peak current | I(OUTL) | 3.4 | | 5 | A | IN+ = low, IN- = high, V(OUTL) = VEE2 + 15 V | 9 |
| Low-level clamp current | I(CLP) | 1.6 | 2.5 | 3.3 | A | V(CLAMP) = VEE2 + 2.5 V | 9 |
| Clamp threshold voltage | V(CLTH) | 1.6 | 2.1 | 2.5 | V | | 9 |
| Clamping voltage (VOUTH - VCC2) | V(CLP-OUTH) | 1.1 | | 1.3 | V | IN+ = high, IN- = low, tCLP = 10 µs, I(OUTH) = 500 mA | 9 |
| Clamping voltage (VOUTL - VCC2) | V(CLP-OUTL) | 1.3 | | 1.5 | V | IN+ = high, IN- = low, tCLP = 10 µs, I(OUTL) = 500 mA | 9 |
| Clamping voltage at CLAMP | V(CLP-CLAMP) | 0.7 | | 1.1 | V | IN+ = High, IN- = Low, I(CLP) = 20 mA | 9 |
| Clamping voltage at OUTL (VCLP - VCC2) | V(CLP-OUTL) | 0.7 | | 1.1 | V | IN+ = High, IN- = Low, I(OUTL) = 20 mA | 9 |
| Blanking-capacitor charge current | I(CHG) | 0.42 | 0.5 | 0.58 | mA | V(DESAT) - GND2 = 2 V | 9 |
| Blanking-capacitor discharge current | I(DCHG) | 9 | | 14 | mA | V(DESAT) - GND2 = 6 V | 9 |
| DESAT threshold voltage with respect to GND2 | V(DSTH) | 8.3 | 9 | 9.5 | V | | 10 |
| DESAT voltage with respect to GND2 | V(DSL) | 0.4 | | 1 | V | when OUTH or OUTL is driven low | 10 |
| Output-signal rise time at OUTH | tr | 12 | 18 | 35 | ns | CLOAD = 1 nF; See Figure 44, Figure 45, and Figure 46 | 10 |
| Output-signal fall time at OUTL | tf | 12 | 20 | 37 | ns | CLOAD = 1 nF | 10 |
| Propagation delay | tPLH, tPHL | 76 | | 110 | ns | CLOAD = 1 nF | 10 |
| Glitch filter on IN+, IN-, RST | tGF (IN,/RST) | 20 | 30 | 40 | ns | CLOAD = 1 nF | 10 |
| DESAT sense to 90% VOUTH/L delay | tDS (90%) | 553 | | 760 | ns | CLOAD = 10 nF | 10 |
| DESAT sense to 10% VOUTH/L delay | tDS (10%) | 2 | | 3.5 | μs | CLOAD = 10 nF | 10 |
| Leading-edge blanking time | tLEB | 310 | 400 | 480 | ns | See Figure 44 and Figure 45 | 10 |
| Glitch filter on RST for resetting FLT | tGF(RSTFLT) | 300 | | 800 | ns | | 10 |
| Common-mode transient immunity | CMTI | 100 | | 120 | kV/μs | VCM = 1500 V, see Figure 47 | 10 |
| Positive-going UVLO1 threshold-voltage input side | VIT+(UVLO1) | | 2.25 | | V | | 9 |
| Negative-going UVLO1 threshold-voltage input side | VIT-(UVLO1) | | 1.7 | | V | | 9 |
| UVLO1 hysteresis voltage (VIT+ - VIT-) input side | VHYS(UVLO1) | | 0.2 | | V | | 9 |
| UVLO2 hysteresis voltage (VIT+ - VIT-) output side | VHYS(UVLO2) | | 1 | | V | | 9 |
| High-level input leakage at IN+ | IIH | | 100 | | µA | IN+ = VCC1 | 9 |
| Low-level input leakage at IN-, RST | IIL | | -100 | | µA | IN- = GND1, RST = GND1 | 9 |
| Pullup current of FLT, RDY | IPU | | 100 | | µA | V(RDY) = GND1, V(FLT) = GND1 | 9 |
| Low-level output voltage at FLT, RDY | V(OL) | | 0.2 | | V | I(FLT) = 5 mA | 9 |
| Active output pulldown voltage | V(OUTPD) | | 2 | | V | I(OUTH/L) = 200 mA, VCC2 = open | 9 |
| Low-level output current during fault condition | I(OLF) | | 130 | | mA | | 9 |
| Clamping voltage (VCLP - VCC2) | V(CLP-CLP) | | 1.3 | | V | IN+ = high, IN- = low, tCLP = 10 µs, I(CLP) = 500 mA | 9 |
| Pulse skew /tPHL - tPLH/ | tsk-p | | 20 | | ns | CLOAD = 1 nF | 10 |
| DESAT-glitch filter delay | tDS (GF) | | 330 | | ns | CLOAD = 1 nF | 10 |
| DESAT sense to FLT-low delay | tDS (FLT) | | 1.4 | | μs | See Figure 46 | 10 |
| Input capacitance | CI | | 2 | | pF | VI = VCC1 / 2 + 0.4 × sin (2πft), f = 1 MHz, VCC1 = 5 V | 10 |
| Junction-to-ambient thermal resistance | RθJA | | 99.6 | | °C/W | | 6 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 48.5 | | °C/W | | 6 |
| Junction-to-board thermal resistance | RθJB | | 56.5 | | °C/W | | 6 |
## CAD (KiCad official)
- Symbol: `ISO5852SMDWREP`
- Footprint: `Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm`
- 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files: `iso5852smdwrep-etched.step` / `iso5852smdwrep-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `iso5852smdwrep.step` / `iso5852smdwrep.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/iso5852s-ep) (44 pp, sha256 `b5e8ab9182fe12c2`, retrieved 2026-11-12, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/iso5852smdwrep-datasheet.pdf)