main
Ray Publish 0.1.0 fe9b108

ISL80102IRAJZ-TK

RENESAS · Linear Voltage Regulators (LDO) · DFN-10(3x3)

ISL80102IRAJZ-TK from RENESAS, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VOUT power_out Output voltage pin; pins 1 and 2 are both VOUT, and a minimum 10µF X5R/X7R ceramic capacitor is required from VOUT to GND with traces no longer than 0.5cm.
2 VOUT power_out Output voltage pin; pins 1 and 2 are both VOUT, regulating 0.8V to 5.5V as set by the external divider.
3 ADJ input ADJ pin for externally set VOUT via a resistor divider to the 0.5V internal reference (VADJ 491mV to 509mV).
4 PG output Open-drain VOUT-in-regulation flag that goes logic low when VOUT is not in regulation (below about 84% of nominal), sinks up to 10mA, needs an external pull-up not above VIN, and must be grounded if not used.
5 GND power_in Ground pin.
6 SS passive External soft-start capacitor adjusts inrush current (about 4.5µA typical charge current); leave this pin open if not used.
7 ENABLE input VIN-independent chip enable, TTL and CMOS compatible, with turn-on threshold of 0.8V typical and 135mV hysteresis; must not be left floating and must be tied to VIN if not used.
8 DNC unconnected Do not connect this pin to ground or supply; leave floating.
9 VIN power_in Input supply pin, 2.2V to 6V operating range, with a minimum 10µF ceramic capacitor to GND with traces no longer than 0.5cm.
10 VIN power_in Input supply pin, 2.2V to 6V operating range; pins 9 and 10 are both VIN.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package DFN-10(3x3)
Category Power Management
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
DC Output Voltage Accuracy VOUT -1.8 1.8 % 2.2V < VIN < 6V; 0A < ILOAD < 3A 4
Feedback Pin Voltage VADJ 491 500 509 mV 0A < ILOAD < full load 4
DC Input Line Regulation -0.4 0.1 0.4 % 2.2V < VIN < 3.6V, VOUT = 1.8V 4
DC Input Line Regulation -0.8 0.1 0.8 % 2.9V < VIN < 6V, VOUT = 2.5V 4
DC Output Load Regulation (ISL80102) -0.6 -0.2 0.6 % ISL80102, 0A < ILOAD < 2A, 2.9V < VIN < 6V; VOUT = 2.5V 4
Feedback Input Current 0.01 1 µA VADJ = 0.5V 4
Ground Pin Current IQ 7.5 9 mA ILOAD = 0A, VOUT + 0.4V < VIN < 6V, VOUT = 2.5V 4
Ground Pin Current IQ 8.5 12 mA ILOAD = 3A, VOUT + 0.4V < VIN < 6V, VOUT = 2.5V 4
Ground Pin Current in Shutdown ISHDN 0.4 µA EN = 0V, VIN = 5V 4
Ground Pin Current in Shutdown ISHDN 3.3 16 µA EN = 0V, VIN = 6V 4
Dropout Voltage VDO 81 125 mV ISL80102, ILOAD = 2A, VOUT = 2.5V 5
Dropout Voltage VDO 60 121 mV ISL80102, ILOAD = 2A, VOUT = 5.5V 5
Output Short-Circuit Current (2A Version) ISC 2.8 A ISL80102, VOUT = 0V 5
Thermal Shutdown Temperature TSD 160 °C 5
Thermal Shutdown Hysteresis TSDn 15 °C 5
Input Supply Ripple Rejection PSRR 55 dB f = 1kHz, ILOAD = 1A; VIN = 2.2V 5
Input Supply Ripple Rejection PSRR 62 dB f = 120Hz, ILOAD = 1A; VIN = 2.2V 5
Output Noise Voltage 49 µVRMS VIN = 2.2V, VOUT = 1.8V, ILOAD = 3A, BW = 100Hz < f < 100kHz 5
Enable Turn-On Threshold VEN(HIGH) 0.616 0.8 0.95 V 2.2V < VIN < 6V 5
Enable Turn-Off Threshold VEN(LOW) 0.463 0.6 V 2.2V < VIN < 6V 5
Enable Hysteresis VEN(HYS) 135 mV 2.2V < VIN < 6V 5
Enable Pin Turn-On Delay tEN 150 µs COUT = 10µF, ILOAD = 1A 5
Enable Pin Leakage Current 1 µA VIN = 6V, EN = 3V 5
Soft-Start Reset Pull-Down Resistance RPD 323 Ω 5
Soft-Start Charge Current ICHG -7 -4.5 -2 µA 5
VOUT PG Flag Threshold 75 84 92 %VOUT 5
VOUT PG Flag Hysteresis 4 % 5
PG Flag Low Voltage 47 100 mV ISINK = 500µA 5
PG Flag Leakage Current 0.05 1 µA VIN = 6V, PG = 6V 5
VIN Relative to GND (abs max) VIN -0.3 6.5 V 4
VOUT Relative to GND (abs max) VOUT -0.3 6.5 V 4
PG, ENABLE, ADJ, SS Relative to GND (abs max) -0.3 6.5 V 4
Maximum Junction Temperature 150 °C Plastic Package 4
Storage Temperature Range -65 150 °C 4
ESD Human Body Model 2.2 kV JESD22 A114F 4
ESD Charge Device Model 1 kV JESD22-C101C 4
Junction Temperature Range TJ -40 125 °C 4
VIN Relative to GND VIN 2.2 6 V 4
VOUT Range VOUT 0.8 5.5 V 4
PG, ENABLE, ADJ, SS Relative to GND 0 6 V 4
PG Sink Current 10 mA 4
Thermal Resistance Junction-to-Ambient θJA 45 °C/W 10 Ld 3x3 DFN, Notes 5, 6 4
Thermal Resistance Junction-to-Case θJC 4 °C/W 10 Ld 3x3 DFN, Notes 5, 6 4
θJB at Pin 3 θJB 14.7 °C/W Note 7 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 9, 10 VIN Input supply pin EPAD EPAD must be connected to a copper plane with as 2

CAD (KiCad official)

  • Symbol: ISL80102IRAJZ-TK
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
  • 3D model files: isl80102irajz-tk-etched.step / isl80102irajz-tk-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl80102irajz-tk.step / isl80102irajz-tk.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (17 pp, sha256 43ae7eb0442be727, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF