Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ISL6722AARZ-T

RENESAS · DC-DC Controllers · QFN-16-EP(3x3)

ISL6722AARZ-T from RENESAS, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC/SLEEP input On the ISL6722A this is the SLEEP input, a logic-level, active-high control that disables the IC and enters low power standby (threshold 1.4V to 2.7V).
2 SLOPE passive Slope compensation pin where an internal 53µA current source charges an external capacitor to GND each cycle, and the resulting ramp is scaled and added to the ISENSE signal.
3 UV input Undervoltage monitor input compared to an internal 1.45V reference to detect an undervoltage condition.
4 OV input Overvoltage monitor input compared to an internal 2.5V reference to detect an overvoltage condition.
5 RTCT passive Oscillator timing pin where RT connects to VREF and CT connects to LGND to set switching frequency (100kHz to 1.0MHz) and maximum duty cycle.
6 ISET input A DC voltage between 0.35V and 1.2V on this pin sets the pulse-by-pulse overcurrent threshold.
7 FB input Feedback voltage input to the inverting input of the error amplifier, whose non-inverting input is tied internally to a 2.515V typical reference.
8 COMP output Error amplifier output and PWM comparator input, where the loop compensation network connects between COMP and FB and the soft-start clamps the maximum COMP voltage.
9 SS passive Soft-start capacitor connection to LGND that sets soft-start duration and the overcurrent shutdown delay.
10 LGND power_in Small-signal reference ground for all analog functions, to be connected externally to PGND with a short trace close to the IC.
11 VREF power_out 5.00V reference voltage output, to be bypassed to LGND with 0.01µF or larger capacitor.
12 VCC power_in Power supply connection for the device (9V to 20V operating), to be bypassed to LGND with a ceramic capacitor close to the VCC and LGND pins.
13 PGND power_in Dedicated ground for the output gate driver, to be connected externally to LGND with a short trace close to the IC.
14 VC power_in Separate collector supply for the output gate drive (GND -0.3V to +20.0V), to be decoupled to PGND with a low ESR 0.1µF or larger capacitor.
15 GATE output High current power driver output for a power MOSFET gate with 1.0A peak current, clamped to about 13.5V and held low when VCC is below UVLO.
16 ISENSE input Current sense input to the PWM and overcurrent comparators, with 0 to 1.5V input range and 5k input impedance.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package QFN-16-EP(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
START Threshold (ISL6722A) 7.95 8.25 8.55 V SLEEP = 0V 6
STOP Threshold 7.4 7.7 8.2 V 6
Hysteresis (ISL6722A) 0.5 0.55 1 V 6
Start-Up Current ICC 100 175 µA VCC < START Threshold 6
OC/OV Fault Operating Current ICC 200 300 µA 6
Operating Current ICC 4.5 10 mA 6
Operating Supply Current IC 8 12 mA Includes 1nF GATE loading 6
Reference Voltage Overall Accuracy VREF 4.95 5 5.05 V Line, load, TA = 0°C to +105°C 6
Reference Voltage Overall Accuracy VREF 4.9 5 5.05 V Line, load, TA = -40°C to +105°C 6
VREF Fault Voltage 4.5 4.65 4.75 V 6
VREF Good Voltage 4.65 4.8 4.95 V 6
VREF Hysteresis 75 165 250 mV 6
VREF Operational Current -10 mA 6
VREF Current Limit -20 mA 6
Current Sense Offset Voltage 0.08 0.1 0.11 V 6
Current Sense Input Voltage Range 0 1.5 V 6
Blanking Time 30 60 100 ns Note 6 7
Gain ACS 0.77 0.79 0.81 V/V VSLOPE = 0V, VFB = 2.3V, VISET = 0.35V, 1.5V; ACS = ISET/ISENSE 7
Open Loop Voltage Gain 60 90 dB Note 6 7
Reference Voltage Initial Accuracy 2.465 2.515 2.565 V VFB = COMP, TA = +25°C (Note 6) 7
Reference Voltage 2.44 2.515 2.59 V VFB = COMP 7
COMP to PWM Gain ACOMP 0.31 0.33 0.35 V/V COMP = 4V, TA = +25°C 7
COMP to PWM Offset 0.51 0.75 0.88 V COMP = 4V 7
FB Input Bias Current -2 0.1 2 µA VFB = 0V 7
COMP Sink Current 2 6 mA COMP = 1.5V, VFB = 2.7V 7
COMP Source Current -0.25 -0.5 mA COMP = 1.5V, VFB = 2.3V 7
COMP VOH 4.25 4.4 5 V VFB = 2.3V 7
COMP VOL 0.4 0.8 1.2 V VFB = 2.7V 7
PSRR 60 80 dB Frequency = 120Hz (Note 6) 7
SS Clamp, VCOMP 2.4 2.5 2.6 V SS = 2.5V, VFB = 0V, ISET = 2V 7
Oscillator Frequency Accuracy 289 318 347 kHz 7
Frequency Variation with VCC -2 2 % TA = +105°C (f20V - f9V)/f9V 7
Frequency Variation with VCC 3 % TA = -40°C (f20V - f9V)/f9V 7
Maximum Duty Cycle 68 75 81 % Note 7 7
Oscillator Discharge Current 0.75 1 1.2 mA TA = 0°C to +105°C 7
Oscillator Discharge Current 0.7 1 1.2 mA TA = -40°C to +105°C 7
Soft-Start Charging Current -40 -55 -70 µA SS = 2V 7
Charged Threshold Voltage 4.26 4.5 4.74 V 7
Initial Overcurrent Discharge Current 30 40 55 µA Sustained OC Threshold < SS < Charged Threshold 7
Overcurrent Shutdown Threshold Voltage 0.11 0.125 0.14 V Charged Threshold minus, TA = +25°C 7
Fault Discharge Current 0.25 1 mA SS = 2V 7
Reset Threshold Voltage 0.22 0.27 0.31 V TA = +25°C 7
Slope Charge Current -45 -53 -65 µA SLOPE = 2V, TA = 0 to +105°C 8
Slope Charge Current -41 -53 -65 µA SLOPE = 2V, TA = -40°C to +105°C 8
Slope Compensation Gain 0.097 0.103 V/V Fraction of slope voltage added to ISENSE, TA = +25°C 8
Slope Compensation Gain 0.082 0.118 V/V Fraction of slope voltage added to ISENSE (Note 4) 8
Slope Discharge Voltage 0.1 0.2 V VRTCT = 4.5V 8
Gate Output Limit Voltage 11 13.5 16 V VC = 20V, CGATE = 1nF, IOUT = 0mA 8
Gate VOH 1.5 2.2 V VC - GATE, VC = 10V, IOUT = 150mA 8
Gate VOL 1.2 1.5 V GATE - PGND, IOUT = 150mA 8
Gate VOL 0.6 0.8 V GATE - PGND, IOUT = 10mA 8
Peak Output Current 1 A VC = 20V, CGATE = 1nF (Note 6) 8
Output Faulted Leakage 1.2 2.6 mA VC = 20V, UV = 0V, GATE = 2V 8
Rise Time 60 100 ns VC = 20V, CGATE = 1nF, 1V < GATE < 9V 8
Fall Time 15 40 ns VC = 20V, CGATE = 1nF, 1V < GATE < 9V 8
Minimum ON time 110 ns ISET = 0.5V; VFB = 0V; VC = 11V; ISENSE to GATE w/10:1 Divider; RTCT = 4.75V through 1k (Note 6) 8
Minimum ISET Voltage 0.35 V 8
Maximum ISET Voltage 1.2 V 8
ISET Bias Current -1 1 µA VISET = 1.00V 8
Restart Delay 150 295 445 ms TA = +25°C 8
Overvoltage Threshold 2.4 2.5 2.6 V 8
Undervoltage Fault Threshold 1.38 1.45 1.52 V 8
Undervoltage Clear Threshold 1.41 1.53 1.62 V 8
Undervoltage Hysteresis Voltage 20 50 100 mV 8
UV Bias Current -1 1 µA VUV = 2.00V 8
OV Bias Current -1 1 µA VOV = 2.00V 8
SLEEP Input Threshold Voltage 1.4 2.7 V Active High 8
SLEEP Input Current 11 25 46 µA VSLEEP = 4.0V 8
ICC @ SLEEP 175 210 µA VCC = 15V 8
Supply Voltage VCC, VC -0.3 20 V GND -0.3V to +20.0V 6
VREF VREF -0.3 5.3 V GND - 0.3V to 5.3V 6
Peak GATE Current 1 A 6
Maximum Junction Temperature -55 150 °C 6
Maximum Storage Temperature Range -65 150 °C 6
Operating Temperature Range -40 105 °C ISL6722AAxZ 6
Supply Voltage Range (Typical) 9 18 V 6
Thermal Resistance Junction to Ambient, 16 Lead QFN θJA 52 °C/W Note 1, 2 6
Thermal Resistance Junction to Case, 16 Lead QFN θJC 4 °C/W Note 1, 2 6

CAD (KiCad official)

  • Symbol: ISL6722AARZ-T
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: isl6722aarz-t-etched.step / isl6722aarz-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl6722aarz-t.step / isl6722aarz-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (26 pp, sha256 b37cf45f90023ac7, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF