main
Ray
Publish 0.1.0
901cd7e
ISL6353IRTZ
RENESAS · Power Management Specialized - PMIC · TQFN-40-EP(5x5)
ISL6353IRTZ from RENESAS, in a TQFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDA | bidirectional | Serial communication bus data signal connected between the CPU and the voltage regulator. |
| 2 | ALERT# | output | Serial communication bus alert signal connected between the CPU and the voltage regulator; ALERT# is specified as an open-drain output with a 7V maximum rating. |
| 3 | SCLK | input | Serial communication bus clock signal connected between the CPU and the voltage regulator. |
| 4 | VR_ON | input | Voltage regulator enable input; a high level logic signal on this pin enables the VR. |
| 5 | PGOOD | output | Open-drain output indicating the regulator is ready to supply regulated voltage; requires an external pull-up resistor. |
| 6 | IMON | output | Sources a current proportional to the regulator output current; a resistor to ground sets a voltage that is sampled by an internal ADC. |
| 7 | VR_HOT# | output | Thermal overload output indicator (open-drain output per the absolute maximum ratings, 7V maximum). |
| 8 | NTC | input | Thermistor input to the VR_HOT# circuit. |
| 9 | VW | passive | Window voltage set pin; a resistor from this pin to COMP programs the switching frequency (18k gives approximately 300kHz). |
| 10 | COMP | output | Output of the error amplifier. |
| 11 | FB | input | Inverting input of the error amplifier. |
| 12 | FB2 | passive | Switches an RC network from VOUT to FB in PS1 and PS2 modes to improve transient performance and phase margin; the pin can be left open if the function is not needed. |
| 13 | ISEN3 | input | Individual current sensing input for Phase 3; leave open when configured for 2-phase operation. |
| 14 | ISEN2 | input | Individual current sensing input for Phase 2; pulling this pin to 5V VDD disables Phase 2 and runs the controller in 1-phase mode. |
| 15 | ISEN1 | input | Individual current sensing input for Phase 1. |
| 16 | VSEN | input | Output voltage sense pin; connect to the output voltage (typically VDDQ) at the desired remote voltage sensing location. |
| 17 | RTN | input | Output voltage sense return pin; connect to ground at the desired remote sensing location. |
| 18 | ISUMN | input | Inverting input of the transconductance amplifier used for current monitoring and overcurrent protection. |
| 19 | ISUMP | input | Non-inverting input of the transconductance amplifier used for current monitoring and overcurrent protection. |
| 20 | VDD | power_in | 5V bias power; the recommended supply is +5V ±5%. |
| 21 | VIN | power_in | Input supply voltage used for input supply feed-forward compensation; recommended input voltage range is 4.5V to 25V. |
| 22 | PROG1 | input | Program pin for the IMAX setting, selected by resistor per Table 6. |
| 23 | BOOT1 | passive | Connect an MLCC capacitor across BOOT1 and PH1; the boot capacitor is charged through an internal switch from VDDP. |
| 24 | UG1 | output | Output of the Phase 1 high-side MOSFET gate driver; connect to the gate of the Phase 1 high-side MOSFET. |
| 25 | PH1 | passive | Current return path for the Phase 1 high-side gate driver; connect to the node of the high-side source, low-side drain and Phase 1 output inductor. |
| 26 | GND | power_in | Electrical ground connection for the IC; connect to the PCB ground plane next to the controller or to the exposed pad via a low impedance path. |
| 27 | LG1 | output | Output of the Phase 1 low-side MOSFET gate driver; connect to the gate of the Phase 1 low-side MOSFET. |
| 28 | PWM3 | output | PWM output for Phase 3; pulling this pin to 5V VDD disables Phase 3 and lets the other phases operate. |
| 29 | VDDP | power_in | Input bias for the internal gate drivers; connect +5V and decouple with at least 1µF MLCC close to the IC. |
| 30 | LG2 | output | Output of the Phase 2 low-side MOSFET gate driver; connect to the gate of the Phase 2 low-side MOSFET. |
| 31 | GND | power_in | Electrical ground connection for the IC; connect to the PCB ground plane next to the controller or to the exposed pad via a low impedance path. |
| 32 | PH2 | passive | Current return path for the Phase 2 high-side gate driver; connect to the node of the high-side source, low-side drain and Phase 2 output inductor. |
| 33 | UG2 | output | Output of the Phase 2 high-side MOSFET gate driver; connect to the gate of the Phase 2 high-side MOSFET. |
| 34 | BOOT2 | passive | Connect an MLCC capacitor across BOOT2 and PH2; the boot capacitor is charged through an internal switch from VDDP. |
| 35 | PROG2 | input | Program pin for VBOOT voltage, droop enable/disable and the number of active phases in PS1 mode, per Table 7. |
| 36 | PSI | input | External power-state pin: ground selects the SVID register power state, high impedance selects PS1, and logic high selects PS2. |
| 37 | VSET2 | input | Logic input used with VSET1 to program the output voltage with external signals, per Table 9. |
| 38 | VSET1 | input | Logic input used with VSET2 to program the output voltage with external signals, per Table 9. |
| 39 | OVP | output | Inverter output that latches high for an overvoltage event and is reset by POR. |
| 40 | ADDR | input | Sets the SVID address offset register, range 0 to 13 (0h to Dh) by resistor per Table 8. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TQFN-40-EP(5x5) |
| Category | Power Management |
| Pins | 41 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| +5V supply current (VR_ON = 1V) | IVDD | 4 | 4 | 4.6 | mA | VR_ON = 1V | 8 |
| Power-on-reset threshold, VDD rising | PORr | 4.35 | 4.5 | V | VDD rising | 8 | |
| Power-on-reset threshold, VDD falling | PORf | 4 | 4.15 | V | VDD falling | 8 | |
| Power-on-reset threshold, VIN rising | PORr | 4 | 4.35 | V | VIN pin rising | 8 | |
| Power-on-reset threshold, VIN falling | PORf | 2.8 | 3.5 | V | VIN pin falling | 8 | |
| System accuracy %Error (VCC_CORE), IRTZ | %Error (VCC_CORE) | -0.8 | 0.8 | % | No load; closed loop, active mode range; VID = 0.75V to 1.50V | 8 | |
| System accuracy (VCC_CORE), IRTZ | %Error (VCC_CORE) | -10 | 10 | mV | No load; closed loop, active mode range; VID = 0.5V to 0.7375V | 8 | |
| System accuracy (VCC_CORE), IRTZ | %Error (VCC_CORE) | -18 | 18 | mV | No load; closed loop, active mode range; VID = 0.3V to 0.4875V | 8 | |
| Maximum output voltage + offset | VCC_CORE(max) | 2.155 | V | VID = FFh, OFFSET = 7Fh | 8 | ||
| Minimum output voltage | VCC_CORE(min) | 0.25 | V | VID = 01h, OFFSET = 00h | 8 | ||
| Nominal channel frequency | fSW(nom) | 280 | 300 | 320 | kHz | RFSET = 18kΩ, 3-channel operation, VCOMP = 1V | 9 |
| Adjustment range (channel frequency) | 200 | 500 | kHz | 9 | |||
| Current-sense amplifier input offset | -0.1 | 0.1 | mV | IFB = 0A | 9 | ||
| PGOOD low voltage | VOL | 0.26 | 0.4 | V | IPGOOD = 4mA | 9 | |
| PGOOD leakage current | IOH | -1 | 1 | µA | PGOOD = 3.3V | 9 | |
| ALERT# pull-down resistance | 7 | 13 | Ω | 9 | |||
| UGATE pull-up resistance | RUGPU | 1 | 1.5 | Ω | 200mA source current | 9 | |
| UGATE sink resistance | RUGPD | 1 | 1.5 | Ω | 250mA sink current | 9 | |
| LGATE pull-up resistance | RLGPU | 1 | 1.5 | Ω | 250mA source current | 9 | |
| LGATE sink resistance | RLGPD | 0.5 | 0.9 | Ω | 250mA sink current | 9 | |
| Pre-charge overvoltage threshold | OVP | 2.29 | 2.35 | V | VSEN rising above setpoint for >1ms | 9 | |
| Overvoltage threshold | OVH | 145 | 175 | 200 | mV | VSEN rising above setpoint for >1ms | 9 |
| Overcurrent threshold, IRTZ 3/2/1-phase PS0 | 54.5 | 60 | 64.5 | µA | IRTZ 3/2/1-Phase Config, PS0 | 9 | |
| Overcurrent threshold, IRTZ 3-phase PS1 drop to 2-phase | 37 | 40 | 43.2 | µA | IRTZ 3-Phase Config, PS1 - Drop to 2-Phase | 9 | |
| Overcurrent threshold, IRTZ 3-phase PS1/2 drop to 1-phase | 18.5 | 20 | 22.25 | µA | IRTZ 3-Phase Config, PS1/2 - Drop to 1-Phase | 9 | |
| Overcurrent threshold, IRTZ 2-phase PS1/2 drop to 1-phase | 27 | 30 | 33 | µA | IRTZ 2-Phase Config, PS1/2 - Drop to 1-Phase | 9 | |
| Way overcurrent threshold, IRTZ 3/2/1-phase PS0 | 74 | 88 | 100 | µA | IRTZ 3/2/1-Phase Config, PS0 | 10 | |
| Way overcurrent threshold, IRTZ 3-phase PS1 drop to 2-phase | 50 | 60 | 68 | µA | IRTZ 3-Phase Config, PS1 - Drop to 2-Phase | 10 | |
| Way overcurrent threshold, IRTZ 3-phase PS1/2 drop to 1-phase | 27 | 32 | 35.8 | µA | IRTZ 3-Phase Config, PS1/2 - Drop to 1-Phase | 10 | |
| NTC source current, IRTZ | 56 | 60 | 62 | µA | NTC = 1.3V | 10 | |
| VR_HOT# trip voltage | 0.895 | 0.91 | V | Falling | 10 | ||
| ALERT# trip voltage | 0.915 | 0.93 | V | Falling | 10 | ||
| IMON output current | IIMON | 12.3 | 12.45 | 12.6 | µA | ISUM- pin current = 50µA | 10 |
| IccMAX alert trip voltage | VIMONMAX | 1.2 | 1.225 | V | Rising | 10 | |
| IccMAX alert reset voltage | 1.05 | 1.14 | V | Falling | 10 | ||
| VR_ON input low | VIL_MAX | 0.3 | V | 10 | |||
| VR_ON input high | VIH_MIN | 0.8 | V | 10 | |||
| VSET1/2 input low | VSETIL_MAX | 1.5 | V | 10 | |||
| VSET1/2 input high | VSETIH_MIN | 3.1 | V | 10 | |||
| PSI sink/source current | 12 | 16 | 20 | µA | PSI Voltage | 10 | |
| PSI pin state PS0 | 0 | 0.51 | V | PS0, VDD = 5V | 10 | ||
| PWM3 output low | VOL_MAX | 1 | V | Sinking 5mA | 10 | ||
| PWM3 output high | VOH_MIN | 3.5 | V | Sourcing 5mA | 10 | ||
| Supply voltage, VDD | VDD | 5 | V | +5V ±5% | 8 | ||
| Supply voltage tolerance, VDD | -5 | 5 | % | VDD = +5V ±5% | 8 | ||
| Input supply voltage, VIN | VIN | 4.5 | 25 | V | 8 | ||
| Ambient temperature, ISL6353IRTZ | TA | -40 | 85 | °C | ISL6353IRTZ | 8 | |
| Junction temperature, ISL6353IRTZ | TJ | -40 | 125 | °C | ISL6353IRTZ | 8 | |
| Supply voltage, VDD | VDD | -0.3 | 7 | V | 8 | ||
| Input supply voltage, VIN | VIN | 28 | V | 8 | |||
| Boot voltage | BOOT | -0.3 | 33 | V | 8 | ||
| Boot to phase voltage (DC) | BOOT-PHASE | -0.3 | 7 | V | DC | 8 | |
| Phase voltage | PHASE | -7 | V | <20ns pulse width, 10µJ | 8 | ||
| LGATE voltage (DC) | LGATE | -0.3 | V | DC; maximum VDD + 0.3V | 8 | ||
| All other pins voltage | -0.3 | V | Maximum VDD + 0.3V | 8 | |||
| Open drain outputs PGOOD, VR_HOT#, ALERT# | -0.3 | 7 | V | 8 | |||
| Maximum junction temperature | TJ | 150 | °C | 8 | |||
| Maximum storage temperature range | TSTG | -65 | 150 | °C | 8 | ||
| Thermal resistance junction-to-ambient, 40 Ld TQFN | θJA | 32 | °C/W | Free air, high effective thermal conductivity test board (Notes 4, 5) | 8 | ||
| Thermal resistance junction-to-case, 40 Ld TQFN | θJC | 3 | °C/W | Case = center of exposed metal pad (Note 5) | 8 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | near this trace. Recommend routing the PH1 trace to the phase 1 high-side MOSFET source pins instead of general copper. | 29 |
CAD (KiCad official)
- Symbol:
ISL6353IRTZ - Footprint:
Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm - 3D model: TQFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
isl6353irtz-etched.step/isl6353irtz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl6353irtz.step/isl6353irtz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (30 pp, sha256
3d503073f071ea00, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ISL6353IRTZ
**RENESAS** · Power Management Specialized - PMIC · TQFN-40-EP(5x5)
ISL6353IRTZ from RENESAS, in a TQFN-40-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDA | bidirectional | Serial communication bus data signal connected between the CPU and the voltage regulator. |
| 2 | ALERT# | output | Serial communication bus alert signal connected between the CPU and the voltage regulator; ALERT# is specified as an open-drain output with a 7V maximum rating. |
| 3 | SCLK | input | Serial communication bus clock signal connected between the CPU and the voltage regulator. |
| 4 | VR_ON | input | Voltage regulator enable input; a high level logic signal on this pin enables the VR. |
| 5 | PGOOD | output | Open-drain output indicating the regulator is ready to supply regulated voltage; requires an external pull-up resistor. |
| 6 | IMON | output | Sources a current proportional to the regulator output current; a resistor to ground sets a voltage that is sampled by an internal ADC. |
| 7 | VR_HOT# | output | Thermal overload output indicator (open-drain output per the absolute maximum ratings, 7V maximum). |
| 8 | NTC | input | Thermistor input to the VR_HOT# circuit. |
| 9 | VW | passive | Window voltage set pin; a resistor from this pin to COMP programs the switching frequency (18k gives approximately 300kHz). |
| 10 | COMP | output | Output of the error amplifier. |
| 11 | FB | input | Inverting input of the error amplifier. |
| 12 | FB2 | passive | Switches an RC network from VOUT to FB in PS1 and PS2 modes to improve transient performance and phase margin; the pin can be left open if the function is not needed. |
| 13 | ISEN3 | input | Individual current sensing input for Phase 3; leave open when configured for 2-phase operation. |
| 14 | ISEN2 | input | Individual current sensing input for Phase 2; pulling this pin to 5V VDD disables Phase 2 and runs the controller in 1-phase mode. |
| 15 | ISEN1 | input | Individual current sensing input for Phase 1. |
| 16 | VSEN | input | Output voltage sense pin; connect to the output voltage (typically VDDQ) at the desired remote voltage sensing location. |
| 17 | RTN | input | Output voltage sense return pin; connect to ground at the desired remote sensing location. |
| 18 | ISUMN | input | Inverting input of the transconductance amplifier used for current monitoring and overcurrent protection. |
| 19 | ISUMP | input | Non-inverting input of the transconductance amplifier used for current monitoring and overcurrent protection. |
| 20 | VDD | power_in | 5V bias power; the recommended supply is +5V ±5%. |
| 21 | VIN | power_in | Input supply voltage used for input supply feed-forward compensation; recommended input voltage range is 4.5V to 25V. |
| 22 | PROG1 | input | Program pin for the IMAX setting, selected by resistor per Table 6. |
| 23 | BOOT1 | passive | Connect an MLCC capacitor across BOOT1 and PH1; the boot capacitor is charged through an internal switch from VDDP. |
| 24 | UG1 | output | Output of the Phase 1 high-side MOSFET gate driver; connect to the gate of the Phase 1 high-side MOSFET. |
| 25 | PH1 | passive | Current return path for the Phase 1 high-side gate driver; connect to the node of the high-side source, low-side drain and Phase 1 output inductor. |
| 26 | GND | power_in | Electrical ground connection for the IC; connect to the PCB ground plane next to the controller or to the exposed pad via a low impedance path. |
| 27 | LG1 | output | Output of the Phase 1 low-side MOSFET gate driver; connect to the gate of the Phase 1 low-side MOSFET. |
| 28 | PWM3 | output | PWM output for Phase 3; pulling this pin to 5V VDD disables Phase 3 and lets the other phases operate. |
| 29 | VDDP | power_in | Input bias for the internal gate drivers; connect +5V and decouple with at least 1µF MLCC close to the IC. |
| 30 | LG2 | output | Output of the Phase 2 low-side MOSFET gate driver; connect to the gate of the Phase 2 low-side MOSFET. |
| 31 | GND | power_in | Electrical ground connection for the IC; connect to the PCB ground plane next to the controller or to the exposed pad via a low impedance path. |
| 32 | PH2 | passive | Current return path for the Phase 2 high-side gate driver; connect to the node of the high-side source, low-side drain and Phase 2 output inductor. |
| 33 | UG2 | output | Output of the Phase 2 high-side MOSFET gate driver; connect to the gate of the Phase 2 high-side MOSFET. |
| 34 | BOOT2 | passive | Connect an MLCC capacitor across BOOT2 and PH2; the boot capacitor is charged through an internal switch from VDDP. |
| 35 | PROG2 | input | Program pin for VBOOT voltage, droop enable/disable and the number of active phases in PS1 mode, per Table 7. |
| 36 | PSI | input | External power-state pin: ground selects the SVID register power state, high impedance selects PS1, and logic high selects PS2. |
| 37 | VSET2 | input | Logic input used with VSET1 to program the output voltage with external signals, per Table 9. |
| 38 | VSET1 | input | Logic input used with VSET2 to program the output voltage with external signals, per Table 9. |
| 39 | OVP | output | Inverter output that latches high for an overvoltage event and is reset by POR. |
| 40 | ADDR | input | Sets the SVID address offset register, range 0 to 13 (0h to Dh) by resistor per Table 8. |
| 41 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TQFN-40-EP(5x5) |
| Category | Power Management |
| Pins | 41 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| +5V supply current (VR_ON = 1V) | IVDD | 4 | 4 | 4.6 | mA | VR_ON = 1V | 8 |
| Power-on-reset threshold, VDD rising | PORr | 4.35 | | 4.5 | V | VDD rising | 8 |
| Power-on-reset threshold, VDD falling | PORf | 4 | | 4.15 | V | VDD falling | 8 |
| Power-on-reset threshold, VIN rising | PORr | 4 | | 4.35 | V | VIN pin rising | 8 |
| Power-on-reset threshold, VIN falling | PORf | 2.8 | | 3.5 | V | VIN pin falling | 8 |
| System accuracy %Error (VCC_CORE), IRTZ | %Error (VCC_CORE) | -0.8 | | 0.8 | % | No load; closed loop, active mode range; VID = 0.75V to 1.50V | 8 |
| System accuracy (VCC_CORE), IRTZ | %Error (VCC_CORE) | -10 | | 10 | mV | No load; closed loop, active mode range; VID = 0.5V to 0.7375V | 8 |
| System accuracy (VCC_CORE), IRTZ | %Error (VCC_CORE) | -18 | | 18 | mV | No load; closed loop, active mode range; VID = 0.3V to 0.4875V | 8 |
| Maximum output voltage + offset | VCC_CORE(max) | | | 2.155 | V | VID = FFh, OFFSET = 7Fh | 8 |
| Minimum output voltage | VCC_CORE(min) | 0.25 | | | V | VID = 01h, OFFSET = 00h | 8 |
| Nominal channel frequency | fSW(nom) | 280 | 300 | 320 | kHz | RFSET = 18kΩ, 3-channel operation, VCOMP = 1V | 9 |
| Adjustment range (channel frequency) | | 200 | | 500 | kHz | | 9 |
| Current-sense amplifier input offset | | -0.1 | | 0.1 | mV | IFB = 0A | 9 |
| PGOOD low voltage | VOL | | 0.26 | 0.4 | V | IPGOOD = 4mA | 9 |
| PGOOD leakage current | IOH | -1 | | 1 | µA | PGOOD = 3.3V | 9 |
| ALERT# pull-down resistance | | 7 | | 13 | Ω | | 9 |
| UGATE pull-up resistance | RUGPU | | 1 | 1.5 | Ω | 200mA source current | 9 |
| UGATE sink resistance | RUGPD | | 1 | 1.5 | Ω | 250mA sink current | 9 |
| LGATE pull-up resistance | RLGPU | | 1 | 1.5 | Ω | 250mA source current | 9 |
| LGATE sink resistance | RLGPD | | 0.5 | 0.9 | Ω | 250mA sink current | 9 |
| Pre-charge overvoltage threshold | OVP | 2.29 | | 2.35 | V | VSEN rising above setpoint for >1ms | 9 |
| Overvoltage threshold | OVH | 145 | 175 | 200 | mV | VSEN rising above setpoint for >1ms | 9 |
| Overcurrent threshold, IRTZ 3/2/1-phase PS0 | | 54.5 | 60 | 64.5 | µA | IRTZ 3/2/1-Phase Config, PS0 | 9 |
| Overcurrent threshold, IRTZ 3-phase PS1 drop to 2-phase | | 37 | 40 | 43.2 | µA | IRTZ 3-Phase Config, PS1 - Drop to 2-Phase | 9 |
| Overcurrent threshold, IRTZ 3-phase PS1/2 drop to 1-phase | | 18.5 | 20 | 22.25 | µA | IRTZ 3-Phase Config, PS1/2 - Drop to 1-Phase | 9 |
| Overcurrent threshold, IRTZ 2-phase PS1/2 drop to 1-phase | | 27 | 30 | 33 | µA | IRTZ 2-Phase Config, PS1/2 - Drop to 1-Phase | 9 |
| Way overcurrent threshold, IRTZ 3/2/1-phase PS0 | | 74 | 88 | 100 | µA | IRTZ 3/2/1-Phase Config, PS0 | 10 |
| Way overcurrent threshold, IRTZ 3-phase PS1 drop to 2-phase | | 50 | 60 | 68 | µA | IRTZ 3-Phase Config, PS1 - Drop to 2-Phase | 10 |
| Way overcurrent threshold, IRTZ 3-phase PS1/2 drop to 1-phase | | 27 | 32 | 35.8 | µA | IRTZ 3-Phase Config, PS1/2 - Drop to 1-Phase | 10 |
| NTC source current, IRTZ | | 56 | 60 | 62 | µA | NTC = 1.3V | 10 |
| VR_HOT# trip voltage | | 0.895 | | 0.91 | V | Falling | 10 |
| ALERT# trip voltage | | 0.915 | | 0.93 | V | Falling | 10 |
| IMON output current | IIMON | 12.3 | 12.45 | 12.6 | µA | ISUM- pin current = 50µA | 10 |
| IccMAX alert trip voltage | VIMONMAX | 1.2 | | 1.225 | V | Rising | 10 |
| IccMAX alert reset voltage | | 1.05 | | 1.14 | V | Falling | 10 |
| VR_ON input low | VIL_MAX | | | 0.3 | V | | 10 |
| VR_ON input high | VIH_MIN | 0.8 | | | V | | 10 |
| VSET1/2 input low | VSETIL_MAX | | | 1.5 | V | | 10 |
| VSET1/2 input high | VSETIH_MIN | 3.1 | | | V | | 10 |
| PSI sink/source current | | 12 | 16 | 20 | µA | PSI Voltage | 10 |
| PSI pin state PS0 | | 0 | | 0.51 | V | PS0, VDD = 5V | 10 |
| PWM3 output low | VOL_MAX | | | 1 | V | Sinking 5mA | 10 |
| PWM3 output high | VOH_MIN | 3.5 | | | V | Sourcing 5mA | 10 |
| Supply voltage, VDD | VDD | | 5 | | V | +5V ±5% | 8 |
| Supply voltage tolerance, VDD | | -5 | | 5 | % | VDD = +5V ±5% | 8 |
| Input supply voltage, VIN | VIN | 4.5 | | 25 | V | | 8 |
| Ambient temperature, ISL6353IRTZ | TA | -40 | | 85 | °C | ISL6353IRTZ | 8 |
| Junction temperature, ISL6353IRTZ | TJ | -40 | | 125 | °C | ISL6353IRTZ | 8 |
| Supply voltage, VDD | VDD | -0.3 | | 7 | V | | 8 |
| Input supply voltage, VIN | VIN | | | 28 | V | | 8 |
| Boot voltage | BOOT | -0.3 | | 33 | V | | 8 |
| Boot to phase voltage (DC) | BOOT-PHASE | -0.3 | | 7 | V | DC | 8 |
| Phase voltage | PHASE | -7 | | | V | <20ns pulse width, 10µJ | 8 |
| LGATE voltage (DC) | LGATE | -0.3 | | | V | DC; maximum VDD + 0.3V | 8 |
| All other pins voltage | | -0.3 | | | V | Maximum VDD + 0.3V | 8 |
| Open drain outputs PGOOD, VR_HOT#, ALERT# | | -0.3 | | 7 | V | | 8 |
| Maximum junction temperature | TJ | | | 150 | °C | | 8 |
| Maximum storage temperature range | TSTG | -65 | | 150 | °C | | 8 |
| Thermal resistance junction-to-ambient, 40 Ld TQFN | θJA | | 32 | | °C/W | Free air, high effective thermal conductivity test board (Notes 4, 5) | 8 |
| Thermal resistance junction-to-case, 40 Ld TQFN | θJC | | 3 | | °C/W | Case = center of exposed metal pad (Note 5) | 8 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | near this trace. Recommend routing the PH1 trace to the phase 1 high-side MOSFET source pins instead of general copper. | 29 |
## CAD (KiCad official)
- Symbol: `ISL6353IRTZ`
- Footprint: `Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm`
- 3D model: TQFN-40-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `isl6353irtz-etched.step` / `isl6353irtz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `isl6353irtz.step` / `isl6353irtz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/isl6353irtz-datasheet.pdf) (30 pp, sha256 `3d503073f071ea00`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/isl6353irtz-datasheet.pdf)