main
Ray
Publish 0.1.0
94e88a1
ISL6341CRZ-T
RENESAS · DC-DC Controllers · TDFN-10-EP(3x3)
ISL6341CRZ-T from RENESAS, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_out | Provides a ground-referenced bias to the upper MOSFET driver through a bootstrap circuit, developing a voltage equal to VGD minus the boot diode drop with respect to PHASE. |
| 2 | PHASE | passive | Connects to the upper MOSFET source and lower MOSFET drain, acting as the UGATE driver sink and sensing the lower MOSFET voltage drop for overcurrent protection. |
| 3 | UGATE | output | Drives the gate of the upper MOSFET with PWM-controlled gate drive and is monitored by the adaptive shoot-through protection circuitry. |
| 4 | LGATE/OCSET | output | Drives the gate of the lower MOSFET from VCC with PWM-controlled gate drive and sets the overcurrent threshold through a resistor to GND during POR or shutdown release. |
| 5 | GND | power_in | Signal and power ground for the IC, to be tied to the ground island or plane through the lowest impedance connection available. |
| 6 | VCC | power_in | Provides the bias supply for the controller and the lower MOSFET gate, to be connected to a well-decoupled 5V to 12V supply. |
| 7 | COMP/EN | bidirectional | Multiplexed pin that is the error amplifier output during soft-start and normal operation, and pulling it low to the 0.7V nominal enable threshold disables the controller. |
| 8 | FB | input | Inverting input of the internal error amplifier, fed from a resistor divider from VOUT to set the regulation voltage. |
| 9 | VOS | input | Monitors the regulator output for OV and UV protection and PGOOD using a divider from VOUT with the same ratio as the FB divider, and has a small pull-up bias current. |
| 10 | PGOOD | output | Open-drain pull-down output reflecting the PGOOD comparator state, requiring an external pull-up to a 6V supply and held low through the soft-start ramp. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TDFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Bias Supply Current (enabled) | IVCC_en | 6.4 | 8.9 | 10.4 | mA | VCC = 12V; enabled (but not switching) | 4 |
| Rising VCC POR Threshold | VPOR | 3.8 | 4.2 | 4.47 | V | 4 | |
| VCC POR Threshold Hysteresis | 0.15 | 0.48 | 0.85 | V | 4 | ||
| Switching Frequency | fOSC | 270 | 300 | 330 | kHz | ISL6341C, ISL6341CC | 4 |
| Reference Voltage Tolerance | VREF | 0.7936 | 0.8 | 0.8064 | V | ISL6341C, ISL6341AC, ISL6341BC, ISL6341CC | 4 |
| OCSET Current Source | IOCSET | 9 | 10 | 11 | µA | LGATE/OCSET = 0V | 5 |
| Enable Threshold (COMP/EN pin) | VENABLE | 0.683 | 0.7 | 0.717 | V | 5 | |
| VOS Rising Trip (PGOOD OV; +10%) | 0.868 | 0.88 | 0.888 | V | 5 | ||
| VOS Falling Trip (PGOOD UV; -10%) | 0.708 | 0.72 | 0.732 | V | 5 | ||
| VOS Rising Threshold (OV; +25%) | 0.98 | 1 | 1.02 | V | 5 | ||
| VOS Threshold (OV; 50% of VOUT) | 0.38 | 0.4 | 0.41 | V | 5 | ||
| VOS Bias Current | -1500 | -250 | -100 | nA | VOS = 0.25V | 5 | |
| PGOOD Low Voltage | PGOOD | 0.1 | 0.18 | 0.3 | V | IPGOOD = 4mA | 5 |
| Input Bias Supply Current (disabled) | IVCC_dis | 7 | mA | VCC = 12V; disabled | 4 | ||
| Supply Voltage Range | VCC | 4.5 | 14.4 | V | 4 | ||
| Ambient Temperature Range (Commercial) | 0 | 70 | °C | ISL6341xCRZ | 4 | ||
| Junction Temperature Range | -40 | 125 | °C | 4 | |||
| Supply Voltage | VCC | -0.3 | 15 | V | relative to GND | 4 | |
| BOOT Voltage | VBOOT-GND | -0.3 | 36 | V | GND - 0.3V to 36V | 4 | |
| BOOT to PHASE Voltage | VBOOT-VPHASE | -0.3 | 15 | V | -0.3V to 16V (<10ns, 10µJ) | 4 | |
| FB, VOS, COMP/EN Voltage | -0.3 | 6 | V | GND - 0.3V to 6V | 4 | ||
| PGOOD Voltage | -0.3 | 7 | V | GND - 0.3V to 7V | 4 | ||
| Maximum Power Dissipation | 1 | W | 4 | ||||
| Maximum Junction Temperature | 150 | °C | Plastic Package | 4 | |||
| Storage Temperature Range | -65 | 150 | °C | 4 | |||
| Thermal Resistance Junction to Ambient | θJA | 44 | °C/W | 10 Ld TDFN, Notes 1, 2 | 4 | ||
| Thermal Resistance Junction to Case | θJC | 3.5 | °C/W | 10 Ld TDFN, Notes 1, 2 | 4 | ||
| Ramp Amplitude | VOSC | 1.5 | VP-P | Note 3 | 4 | ||
| DC Gain | GAIN | 96 | dB | Note 3 | 4 | ||
| Gain-Bandwidth Product | GBWP | 20 | MHz | Note 3 | 4 | ||
| Slew Rate | SR | 8 | V/µs | Note 3 | 4 | ||
| VOS Rising Trip (PGOOD OV) Hysteresis | 16 | mV | 5 | ||||
| VOS Falling Trip (PGOOD UV) Hysteresis | 16 | mV | 5 | ||||
| Upper Gate Source Impedance | RUG-SRCh | 2.1 | Ω | VCC = 12V; I = 50mA | 4 | ||
| Upper Gate Sink Impedance | RUG-SNKh | 1.6 | Ω | VCC = 12V; I = 50mA | 4 | ||
| Lower Gate Source Impedance | RLG-SRCh | 1.4 | Ω | VCC = 12V; I = 50mA | 4 | ||
| Lower Gate Sink Impedance | RLG-SNKh | 1 | Ω | VCC = 12V; I = 50mA | 4 | ||
| Upper Gate Source Impedance | RUG-SRCl | 2.4 | Ω | VCC = 5V; I = 50mA | 4 | ||
| Upper Gate Sink Impedance | RUG-SNKl | 1.7 | Ω | VCC = 5V; I = 50mA | 5 | ||
| Lower Gate Source Impedance | RLG-SRCl | 1.5 | Ω | VCC = 5V; I = 50mA | 5 | ||
| Lower Gate Sink Impedance | RLG-SNKl | 1.1 | Ω | VCC = 5V; I = 50mA | 5 |
CAD (KiCad official)
- Symbol:
ISL6341CRZ-T - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
isl6341crz-t-etched.step/isl6341crz-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl6341crz-t.step/isl6341crz-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (18 pp, sha256
27f68b4d5075c3ec, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ISL6341CRZ-T
**RENESAS** · DC-DC Controllers · TDFN-10-EP(3x3)
ISL6341CRZ-T from RENESAS, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_out | Provides a ground-referenced bias to the upper MOSFET driver through a bootstrap circuit, developing a voltage equal to VGD minus the boot diode drop with respect to PHASE. |
| 2 | PHASE | passive | Connects to the upper MOSFET source and lower MOSFET drain, acting as the UGATE driver sink and sensing the lower MOSFET voltage drop for overcurrent protection. |
| 3 | UGATE | output | Drives the gate of the upper MOSFET with PWM-controlled gate drive and is monitored by the adaptive shoot-through protection circuitry. |
| 4 | LGATE/OCSET | output | Drives the gate of the lower MOSFET from VCC with PWM-controlled gate drive and sets the overcurrent threshold through a resistor to GND during POR or shutdown release. |
| 5 | GND | power_in | Signal and power ground for the IC, to be tied to the ground island or plane through the lowest impedance connection available. |
| 6 | VCC | power_in | Provides the bias supply for the controller and the lower MOSFET gate, to be connected to a well-decoupled 5V to 12V supply. |
| 7 | COMP/EN | bidirectional | Multiplexed pin that is the error amplifier output during soft-start and normal operation, and pulling it low to the 0.7V nominal enable threshold disables the controller. |
| 8 | FB | input | Inverting input of the internal error amplifier, fed from a resistor divider from VOUT to set the regulation voltage. |
| 9 | VOS | input | Monitors the regulator output for OV and UV protection and PGOOD using a divider from VOUT with the same ratio as the FB divider, and has a small pull-up bias current. |
| 10 | PGOOD | output | Open-drain pull-down output reflecting the PGOOD comparator state, requiring an external pull-up to a 6V supply and held low through the soft-start ramp. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TDFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Bias Supply Current (enabled) | IVCC_en | 6.4 | 8.9 | 10.4 | mA | VCC = 12V; enabled (but not switching) | 4 |
| Rising VCC POR Threshold | VPOR | 3.8 | 4.2 | 4.47 | V | | 4 |
| VCC POR Threshold Hysteresis | | 0.15 | 0.48 | 0.85 | V | | 4 |
| Switching Frequency | fOSC | 270 | 300 | 330 | kHz | ISL6341C, ISL6341CC | 4 |
| Reference Voltage Tolerance | VREF | 0.7936 | 0.8 | 0.8064 | V | ISL6341C, ISL6341AC, ISL6341BC, ISL6341CC | 4 |
| OCSET Current Source | IOCSET | 9 | 10 | 11 | µA | LGATE/OCSET = 0V | 5 |
| Enable Threshold (COMP/EN pin) | VENABLE | 0.683 | 0.7 | 0.717 | V | | 5 |
| VOS Rising Trip (PGOOD OV; +10%) | | 0.868 | 0.88 | 0.888 | V | | 5 |
| VOS Falling Trip (PGOOD UV; -10%) | | 0.708 | 0.72 | 0.732 | V | | 5 |
| VOS Rising Threshold (OV; +25%) | | 0.98 | 1 | 1.02 | V | | 5 |
| VOS Threshold (OV; 50% of VOUT) | | 0.38 | 0.4 | 0.41 | V | | 5 |
| VOS Bias Current | | -1500 | -250 | -100 | nA | VOS = 0.25V | 5 |
| PGOOD Low Voltage | PGOOD | 0.1 | 0.18 | 0.3 | V | IPGOOD = 4mA | 5 |
| Input Bias Supply Current (disabled) | IVCC_dis | | | 7 | mA | VCC = 12V; disabled | 4 |
| Supply Voltage Range | VCC | 4.5 | | 14.4 | V | | 4 |
| Ambient Temperature Range (Commercial) | | 0 | | 70 | °C | ISL6341xCRZ | 4 |
| Junction Temperature Range | | -40 | | 125 | °C | | 4 |
| Supply Voltage | VCC | -0.3 | | 15 | V | relative to GND | 4 |
| BOOT Voltage | VBOOT-GND | -0.3 | | 36 | V | GND - 0.3V to 36V | 4 |
| BOOT to PHASE Voltage | VBOOT-VPHASE | -0.3 | | 15 | V | -0.3V to 16V (<10ns, 10µJ) | 4 |
| FB, VOS, COMP/EN Voltage | | -0.3 | | 6 | V | GND - 0.3V to 6V | 4 |
| PGOOD Voltage | | -0.3 | | 7 | V | GND - 0.3V to 7V | 4 |
| Maximum Power Dissipation | | | | 1 | W | | 4 |
| Maximum Junction Temperature | | | | 150 | °C | Plastic Package | 4 |
| Storage Temperature Range | | -65 | | 150 | °C | | 4 |
| Thermal Resistance Junction to Ambient | θJA | | 44 | | °C/W | 10 Ld TDFN, Notes 1, 2 | 4 |
| Thermal Resistance Junction to Case | θJC | | 3.5 | | °C/W | 10 Ld TDFN, Notes 1, 2 | 4 |
| Ramp Amplitude | VOSC | | 1.5 | | VP-P | Note 3 | 4 |
| DC Gain | GAIN | | 96 | | dB | Note 3 | 4 |
| Gain-Bandwidth Product | GBWP | | 20 | | MHz | Note 3 | 4 |
| Slew Rate | SR | | 8 | | V/µs | Note 3 | 4 |
| VOS Rising Trip (PGOOD OV) Hysteresis | | | 16 | | mV | | 5 |
| VOS Falling Trip (PGOOD UV) Hysteresis | | | 16 | | mV | | 5 |
| Upper Gate Source Impedance | RUG-SRCh | | 2.1 | | Ω | VCC = 12V; I = 50mA | 4 |
| Upper Gate Sink Impedance | RUG-SNKh | | 1.6 | | Ω | VCC = 12V; I = 50mA | 4 |
| Lower Gate Source Impedance | RLG-SRCh | | 1.4 | | Ω | VCC = 12V; I = 50mA | 4 |
| Lower Gate Sink Impedance | RLG-SNKh | | 1 | | Ω | VCC = 12V; I = 50mA | 4 |
| Upper Gate Source Impedance | RUG-SRCl | | 2.4 | | Ω | VCC = 5V; I = 50mA | 4 |
| Upper Gate Sink Impedance | RUG-SNKl | | 1.7 | | Ω | VCC = 5V; I = 50mA | 5 |
| Lower Gate Source Impedance | RLG-SRCl | | 1.5 | | Ω | VCC = 5V; I = 50mA | 5 |
| Lower Gate Sink Impedance | RLG-SNKl | | 1.1 | | Ω | VCC = 5V; I = 50mA | 5 |
## CAD (KiCad official)
- Symbol: `ISL6341CRZ-T`
- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`
- 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `isl6341crz-t-etched.step` / `isl6341crz-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `isl6341crz-t.step` / `isl6341crz-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/isl6341crz-t-datasheet.pdf) (18 pp, sha256 `27f68b4d5075c3ec`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/isl6341crz-t-datasheet.pdf)