main
Ray
Publish 0.1.0
e8c1f69
ISL29501IRZ-T7
RENESAS · Position Sensor · QFN-24(4x5)
ISL29501IRZ-T7 from RENESAS, in a QFN-24(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVSS | power_in | Analog ground; the datasheet says to tie this pin to AVSS. |
| 2 | AVSS | power_in | Analog ground; the datasheet says to tie this pin to AVSS. |
| 3 | CEn | input | Chip enable, active low. |
| 4 | A2 | input | I2C address bit; pull to DVCC or DVSS. |
| 5 | SDA | bidirectional | I2C data bus. |
| 6 | SCL | input | I2C clock bus. |
| 7 | A1 | input | I2C ID address bit; pull to DVCC or DVSS. |
| 8 | IRQ | output | Interrupt, active low, open-drain output to the host; a 2.7kΩ pull-up to supply is required. |
| 9 | SS | input | Sample start input, active on a HIGH to LOW edge. |
| 10 | EVSS | power_in | Emitter driver ground; connects to the cathode of the emitter. |
| 11 | EIR | output | Emitter driver output; connects to the anode of the emitter. |
| 12 | EVCC | power_in | Emitter driver supply, 2.7V to 3.3V range per the supply spec; decouple with 2.2µF or larger capacitor along with 0.1µF for high frequency. |
| 13 | AVSS | power_in | Analog ground; the datasheet says to tie this pin to AVSS. |
| 14 | DVCC | power_in | Digital power supply, 2.7V to 3.3V. |
| 15 | DVSS | power_in | Digital power ground. |
| 16 | AVSS | power_in | Analog power ground. |
| 17 | AVCC | power_in | Analog power supply, 2.7V to 3.3V. |
| 18 | VOUT | power_out | AFE LDO output, tied to AVDD; decouple with a 1µF and 0.01µF capacitor pair. |
| 19 | AVDD | power_in | AFE analog supply; tied to VOUT. |
| 20 | AVSS | power_in | Analog ground shield. |
| 21 | PDp | input | Photodiode cathode input. |
| 22 | PDn | input | Photodiode anode input. |
| 23 | AVSS | power_in | Analog ground shield. |
| 24 | RSET | passive | Sets chip bias current; tie to a 10kΩ 1% resistor to AVSS. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-24(4x5) |
| Category | Sensors |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Modulation frequency | fmod | 4.45 | 4.5 | 4.65 | MHz | Modulation frequency of emitter | 5 |
| Chip Power Supply (DVCC, AVCC, EVCC) | 2.7 | 3 | 3.3 | V | 5 | ||
| Supply Voltage (recommended) | 2.7 | 3.3 | V | 5 | |||
| Temperature (recommended) | -40 | 85 | °C | 5 | |||
| Supply Voltage Range (absolute) | -0.2 | 4 | V | 5 | |||
| Voltage on All Other Pins | -0.3 | V | Upper limit printed as (VCC) + 0.3V, not numeric | 5 | |||
| ESD Human Body Model | 2 | kV | Tested per JESD22-A114E; IRQ and SDA passed 1kV | 5 | |||
| ESD Machine Model | 200 | V | Tested per JESD22-A115-A | 5 | |||
| Latch-Up | 100 | mA | Tested per JESD-78C; Class 2, Level A | 5 | |||
| Maximum Junction Temperature | 150 | °C | Plastic package | 5 | |||
| Quiescent Current - Sleep Mode (DVCC+AVCC+EVCC) | IS-HS | 2.5 | µA | CEn = 1; I2C disable; register values retained; SS = SDA = SCL = VCC | 5 | ||
| Quiescent Current - Shutdown (DVCC+AVCC+EVCC) | IS-SD | 1 | µA | CEn = 0; I2C enable; register values retained; all other functions disabled | 5 | ||
| Delay from Chip Enable to First Sample | tcen_fs | 500 | µs | Note 7 | 5 | ||
| Delay between Sleep Mode to Start of First Sample | tsleep_fs | 3 | µs | Note 7 | 5 | ||
| Maximum AFE Input Current PDp/PDn | Imax_PD | 12.8 | µA | Design recommendation | 5 | ||
| Maximum Photodiode Capacitance (recommended) | Cmax | 15 | pF | Design recommendation | 5 | ||
| Supply Voltage Range for I2C Specification | VI2C | 1.8 | 3.3 | V | 6 | ||
| Input Leakage | IIL | 1 | µA | VIN = GND to VCC | 6 | ||
| Input LOW Voltage | VIL | -0.3 | V | Upper limit printed as 0.3 x VCC, not numeric | 6 | ||
| SDA Output Buffer low Voltage | VOL | 0 | 0.4 | V | IOL = 3mA | 6 | |
| SCL Frequency | fSCL | 400 | kHz | 6 | |||
| Pulse Width Suppression Time at SDA and SCL Inputs | tsp | 50 | ns | Any pulse narrower than the maximum specification is suppressed | 6 | ||
| SCL Falling Edge to SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VCC until SDA exits the 30% to 70% of VCC window | 6 | ||
| Time the Bus Must Be Free Before Start of New Transmission | tBUF | 1300 | ns | SDA crossing 70% of VCC during STOP to SDA crossing 70% of VCC during START | 6 | ||
| Clock Low Time | tLOW | 1300 | ns | Measured at the 30% of VCC crossing | 6 | ||
| Clock High Time | tHIGH | 600 | ns | Measured at the 70% of VCC crossing | 6 | ||
| START Condition Set-Up Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge; both crossing 70% of VCC | 6 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC | 6 | ||
| Input Data Set-Up Time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VCC window to SCL rising edge crossing 30% of VCC | 6 | ||
| Input Data Hold Time | tHD:DAT | 0 | ns | From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window | 6 | ||
| STOP Condition Set-Up Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VCC to SDA rising edge crossing 30% of VCC | 6 | ||
| STOP Condition Hold Time for Read or Volatile Only Write | tHD:STO | 1300 | ns | From SDA rising edge to SCL falling edge; both crossing 70% of VCC | 6 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VCC until SDA enters the 30% to 70% of VCC window | 6 | ||
| SDA and SCL Rise Time | tR | 250 | ns | From 30% to 70% of VCC; minimum printed as 20 + 0.1 x cb, not numeric | 6 | ||
| SDA and SCL Fall Time | tF | 250 | ns | From 70% to 30% of VCC; minimum printed as 20 + 0.1 x cb, not numeric | 6 | ||
| Capacitive Loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 6 | |
| Output Leakage Current (SDA only) | ILO | 1 | µA | VOUT = GND to VCC | 6 | ||
| A1, A2, SDA, SCL Input Buffer low Voltage | VIL | -0.3 | V | Upper limit printed as VCC x 0.3, not numeric | 6 | ||
| Thermal Resistance Junction-to-Ambient (QFN) | JA | 35 | °C/W | Measured in free air on high-effective thermal conductivity test board (Notes 4, 5) | 5 | ||
| Thermal Resistance Junction-to-Case (QFN) | JC | 1.2 | °C/W | Case temp at center of exposed metal pad (Note 5) | 5 | ||
| Chip Current While Measuring (DVCC+AVCC+EVCC) | IDDact | 55 | mA | Emitter duty cycle = 50%, 0x90 = 06h, 0x91 = 00h | 5 | ||
| Voltage at PDp | VPDp | 1.7 | V | 5 | |||
| Voltage at PDn | VPDn | 0.75 | V | 5 | |||
| Differential I to V Conversion Range (TIA Gain) | 8 | kΩ | TIA Gain 0x97[0:1], b0 = 0 and b1 = 0 default; printed as 8k kΩ | 5 | |||
| Pin Capacitance | Cpin | 10 | pF | Note 10 | 6 | ||
| Off-chip SDA and SCL Bus Pull-Up Resistor | Rpu | 1 | kΩ | Maximum determined by tR and tF; for Cb = 400pF about 2kΩ to 2.5kΩ | 6 |
CAD (KiCad official)
- Symbol:
ISL29501IRZ-T7 - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-24(4x5) (KiCad packages3D, STEP)
- 3D model files:
isl29501irz-t7-etched.step/isl29501irz-t7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl29501irz-t7.step/isl29501irz-t7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (23 pp, sha256
9b7bcfa0ed5c56be, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ISL29501IRZ-T7
**RENESAS** · Position Sensor · QFN-24(4x5)
ISL29501IRZ-T7 from RENESAS, in a QFN-24(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AVSS | power_in | Analog ground; the datasheet says to tie this pin to AVSS. |
| 2 | AVSS | power_in | Analog ground; the datasheet says to tie this pin to AVSS. |
| 3 | CEn | input | Chip enable, active low. |
| 4 | A2 | input | I2C address bit; pull to DVCC or DVSS. |
| 5 | SDA | bidirectional | I2C data bus. |
| 6 | SCL | input | I2C clock bus. |
| 7 | A1 | input | I2C ID address bit; pull to DVCC or DVSS. |
| 8 | IRQ | output | Interrupt, active low, open-drain output to the host; a 2.7kΩ pull-up to supply is required. |
| 9 | SS | input | Sample start input, active on a HIGH to LOW edge. |
| 10 | EVSS | power_in | Emitter driver ground; connects to the cathode of the emitter. |
| 11 | EIR | output | Emitter driver output; connects to the anode of the emitter. |
| 12 | EVCC | power_in | Emitter driver supply, 2.7V to 3.3V range per the supply spec; decouple with 2.2µF or larger capacitor along with 0.1µF for high frequency. |
| 13 | AVSS | power_in | Analog ground; the datasheet says to tie this pin to AVSS. |
| 14 | DVCC | power_in | Digital power supply, 2.7V to 3.3V. |
| 15 | DVSS | power_in | Digital power ground. |
| 16 | AVSS | power_in | Analog power ground. |
| 17 | AVCC | power_in | Analog power supply, 2.7V to 3.3V. |
| 18 | VOUT | power_out | AFE LDO output, tied to AVDD; decouple with a 1µF and 0.01µF capacitor pair. |
| 19 | AVDD | power_in | AFE analog supply; tied to VOUT. |
| 20 | AVSS | power_in | Analog ground shield. |
| 21 | PDp | input | Photodiode cathode input. |
| 22 | PDn | input | Photodiode anode input. |
| 23 | AVSS | power_in | Analog ground shield. |
| 24 | RSET | passive | Sets chip bias current; tie to a 10kΩ 1% resistor to AVSS. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-24(4x5) |
| Category | Sensors |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Modulation frequency | fmod | 4.45 | 4.5 | 4.65 | MHz | Modulation frequency of emitter | 5 |
| Chip Power Supply (DVCC, AVCC, EVCC) | | 2.7 | 3 | 3.3 | V | | 5 |
| Supply Voltage (recommended) | | 2.7 | | 3.3 | V | | 5 |
| Temperature (recommended) | | -40 | | 85 | °C | | 5 |
| Supply Voltage Range (absolute) | | -0.2 | | 4 | V | | 5 |
| Voltage on All Other Pins | | -0.3 | | | V | Upper limit printed as (VCC) + 0.3V, not numeric | 5 |
| ESD Human Body Model | | | | 2 | kV | Tested per JESD22-A114E; IRQ and SDA passed 1kV | 5 |
| ESD Machine Model | | | | 200 | V | Tested per JESD22-A115-A | 5 |
| Latch-Up | | | | 100 | mA | Tested per JESD-78C; Class 2, Level A | 5 |
| Maximum Junction Temperature | | | | 150 | °C | Plastic package | 5 |
| Quiescent Current - Sleep Mode (DVCC+AVCC+EVCC) | IS-HS | | | 2.5 | µA | CEn = 1; I2C disable; register values retained; SS = SDA = SCL = VCC | 5 |
| Quiescent Current - Shutdown (DVCC+AVCC+EVCC) | IS-SD | | | 1 | µA | CEn = 0; I2C enable; register values retained; all other functions disabled | 5 |
| Delay from Chip Enable to First Sample | tcen_fs | | | 500 | µs | Note 7 | 5 |
| Delay between Sleep Mode to Start of First Sample | tsleep_fs | | | 3 | µs | Note 7 | 5 |
| Maximum AFE Input Current PDp/PDn | Imax_PD | | | 12.8 | µA | Design recommendation | 5 |
| Maximum Photodiode Capacitance (recommended) | Cmax | | | 15 | pF | Design recommendation | 5 |
| Supply Voltage Range for I2C Specification | VI2C | 1.8 | | 3.3 | V | | 6 |
| Input Leakage | IIL | | | 1 | µA | VIN = GND to VCC | 6 |
| Input LOW Voltage | VIL | -0.3 | | | V | Upper limit printed as 0.3 x VCC, not numeric | 6 |
| SDA Output Buffer low Voltage | VOL | 0 | | 0.4 | V | IOL = 3mA | 6 |
| SCL Frequency | fSCL | | | 400 | kHz | | 6 |
| Pulse Width Suppression Time at SDA and SCL Inputs | tsp | | | 50 | ns | Any pulse narrower than the maximum specification is suppressed | 6 |
| SCL Falling Edge to SDA Output Data Valid | tAA | | | 900 | ns | SCL falling edge crossing 30% of VCC until SDA exits the 30% to 70% of VCC window | 6 |
| Time the Bus Must Be Free Before Start of New Transmission | tBUF | 1300 | | | ns | SDA crossing 70% of VCC during STOP to SDA crossing 70% of VCC during START | 6 |
| Clock Low Time | tLOW | 1300 | | | ns | Measured at the 30% of VCC crossing | 6 |
| Clock High Time | tHIGH | 600 | | | ns | Measured at the 70% of VCC crossing | 6 |
| START Condition Set-Up Time | tSU:STA | 600 | | | ns | SCL rising edge to SDA falling edge; both crossing 70% of VCC | 6 |
| START Condition Hold Time | tHD:STA | 600 | | | ns | From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC | 6 |
| Input Data Set-Up Time | tSU:DAT | 100 | | | ns | From SDA exiting the 30% to 70% of VCC window to SCL rising edge crossing 30% of VCC | 6 |
| Input Data Hold Time | tHD:DAT | 0 | | | ns | From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window | 6 |
| STOP Condition Set-Up Time | tSU:STO | 600 | | | ns | From SCL rising edge crossing 70% of VCC to SDA rising edge crossing 30% of VCC | 6 |
| STOP Condition Hold Time for Read or Volatile Only Write | tHD:STO | 1300 | | | ns | From SDA rising edge to SCL falling edge; both crossing 70% of VCC | 6 |
| Output Data Hold Time | tDH | 0 | | | ns | From SCL falling edge crossing 30% of VCC until SDA enters the 30% to 70% of VCC window | 6 |
| SDA and SCL Rise Time | tR | | | 250 | ns | From 30% to 70% of VCC; minimum printed as 20 + 0.1 x cb, not numeric | 6 |
| SDA and SCL Fall Time | tF | | | 250 | ns | From 70% to 30% of VCC; minimum printed as 20 + 0.1 x cb, not numeric | 6 |
| Capacitive Loading of SDA or SCL | Cb | 10 | | 400 | pF | Total on-chip and off-chip | 6 |
| Output Leakage Current (SDA only) | ILO | | | 1 | µA | VOUT = GND to VCC | 6 |
| A1, A2, SDA, SCL Input Buffer low Voltage | VIL | -0.3 | | | V | Upper limit printed as VCC x 0.3, not numeric | 6 |
| Thermal Resistance Junction-to-Ambient (QFN) | JA | | 35 | | °C/W | Measured in free air on high-effective thermal conductivity test board (Notes 4, 5) | 5 |
| Thermal Resistance Junction-to-Case (QFN) | JC | | 1.2 | | °C/W | Case temp at center of exposed metal pad (Note 5) | 5 |
| Chip Current While Measuring (DVCC+AVCC+EVCC) | IDDact | | 55 | | mA | Emitter duty cycle = 50%, 0x90 = 06h, 0x91 = 00h | 5 |
| Voltage at PDp | VPDp | | 1.7 | | V | | 5 |
| Voltage at PDn | VPDn | | 0.75 | | V | | 5 |
| Differential I to V Conversion Range (TIA Gain) | | | 8 | | kΩ | TIA Gain 0x97[0:1], b0 = 0 and b1 = 0 default; printed as 8k kΩ | 5 |
| Pin Capacitance | Cpin | | 10 | | pF | Note 10 | 6 |
| Off-chip SDA and SCL Bus Pull-Up Resistor | Rpu | | 1 | | kΩ | Maximum determined by tR and tF; for Cb = 400pF about 2kΩ to 2.5kΩ | 6 |
## CAD (KiCad official)
- Symbol: `ISL29501IRZ-T7`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`
- 3D model: QFN-24(4x5) (KiCad packages3D, STEP)
- 3D model files: `isl29501irz-t7-etched.step` / `isl29501irz-t7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `isl29501irz-t7.step` / `isl29501irz-t7.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/isl29501irz-t7-datasheet.pdf) (23 pp, sha256 `9b7bcfa0ed5c56be`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/isl29501irz-t7-datasheet.pdf)