Generated by kicad-footprint-generator · KiCad file format 20260206
ISL23325TFVZ
RENESAS · Digital Potentiometers · TSSOP-14
ISL23325TFVZ from RENESAS, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin for the device. |
| 2 | VLOGIC | power_in | I2C bus/logic supply, range 1.2V to 5.5V, independent of VCC. |
| 3 | SDA | bidirectional | Serial bus data input/open-drain output for the I2C interface, which requires an external pull-up resistor. |
| 4 | SCL | input | Serial clock input for the I2C interface, which requires an external pull-up resistor. |
| 5 | A0 | input | Hardwired slave address pin for the I2C bus, to be tied to VLOGIC or GND. |
| 6 | A1 | input | Hardwired slave address pin for the I2C bus, to be tied to VLOGIC or GND. |
| 7 | A2 | input | Hardwired slave address pin for the I2C bus, to be tied to VLOGIC or GND. |
| 8 | RL1 | passive | DCP1 'low' terminal; DCP terminal voltage must stay between 0 and VCC. |
| 9 | RW1 | passive | DCP1 wiper terminal, whose position is set by the WR1 register. |
| 10 | RH1 | passive | DCP1 'high' terminal; DCP terminal voltage must stay between 0 and VCC. |
| 11 | RH0 | passive | DCP0 'high' terminal; DCP terminal voltage must stay between 0 and VCC. |
| 12 | RW0 | passive | DCP0 wiper terminal, whose position is set by the WR0 register. |
| 13 | RL0 | passive | DCP0 'low' terminal; DCP terminal voltage must stay between 0 and VCC. |
| 14 | VCC | power_in | Analog power supply for the potentiometer section, range 1.7V to 5.5V, independent of VLOGIC. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TSSOP-14 |
| Category | Data Converters |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC | VCC | -0.3 | 6 | V | 4 | ||
| Supply voltage VLOGIC | VLOGIC | -0.3 | 6 | V | 4 | ||
| Voltage on any DCP terminal pin | -0.3 | 6 | V | 4 | |||
| Voltage on any digital pin | -0.3 | 6 | V | 4 | |||
| Wiper current | IW | -6 | 6 | mA | 10 s | 4 | |
| Operating temperature range | -40 | 125 | °C | 4 | |||
| VCC supply voltage | VCC | 1.7 | 5.5 | V | 4 | ||
| VLOGIC supply voltage | VLOGIC | 1.2 | 5.5 | V | 4 | ||
| DCP terminal voltage | VRH, VRL | 0 | V | upper limit printed as VCC | 4 | ||
| Max wiper current | IW | -3 | 3 | mA | 4 | ||
| Thermal resistance junction-to-ambient, 14 Ld TSSOP | JA | 112 | °C/W | typical, 14 Ld TSSOP package | 4 | ||
| Thermal resistance junction-to-case, 14 Ld TSSOP | JC | 40 | °C/W | typical, 14 Ld TSSOP package | 4 | ||
| RH to RL resistance tolerance | -20 | 2 | 20 | % | 4 | ||
| Wiper resistance RW | RW | 70 | 200 | Ω | RH floating, VRL = 0V, VCC = 2.7V to 5.5V | 4 | |
| Wiper resistance RW at VCC 1.7V | RW | 580 | Ω | VCC = 1.7V | 4 | ||
| Leakage on DCP pins | ILkgDCP | -0.4 | 0.4 | µA | Voltage at pin from GND to VCC | 4 | |
| Integral non-linearity INL | INL | -0.5 | 0.15 | 0.5 | LSB | Guaranteed monotonic; U, T option | 5 |
| Differential non-linearity DNL | DNL | -0.4 | 0.1 | 0.4 | LSB | Guaranteed monotonic; U, T option | 5 |
| Full-scale error | FSerror | -2 | -0.5 | 0 | LSB | U, T option | 5 |
| Zero-scale error | ZSerror | 0 | 0.4 | 2 | LSB | U, T option | 5 |
| DCP to DCP matching (voltage divider) | Vmatch | -2 | 0.5 | 2 | LSB | DCPs at same tap position, same voltage at all RH and RL terminals | 5 |
| Integral non-linearity RINL, VCC 2.7V to 5.5V | RINL | -1 | 0.3 | 1 | MI | U, T option; VCC = 2.7V to 5.5V | 5 |
| Integral non-linearity RINL, VCC 1.7V | RINL | 2.1 | MI | U, T option; VCC = 1.7V | 5 | ||
| Differential non-linearity RDNL, VCC 2.7V to 5.5V | RDNL | -0.5 | 0.15 | 0.5 | MI | U, T option; VCC = 2.7V to 5.5V | 5 |
| Differential non-linearity RDNL, VCC 1.7V | RDNL | -0.35 | 0.35 | MI | U, T option; VCC = 1.7V | 5 | |
| Offset RW at wiper 0, VCC 2.7V to 5.5V | Roffset | 0 | 0.5 | 2 | MI | U, T option; VCC = 2.7V to 5.5V | 6 |
| Offset RW at wiper 0, VCC 1.7V | Roffset | 1.1 | MI | U, T option; VCC = 1.7V | 6 | ||
| DCP to DCP resistance matching | Rmatch | -2 | 2 | LSB | Any two DCPs at same tap position with same terminal voltages | 6 | |
| VLOGIC supply current (write/read) | ILOGIC | 200 | µA | VLOGIC = 5.5V, VCC = 5.5V, fSCL = 400kHz | 6 | ||
| VLOGIC supply current (write/read) | ILOGIC | 5 | µA | VLOGIC = 1.2V, VCC = 1.7V, fSCL = 400kHz | 6 | ||
| VCC supply current (write/read) | ICC | 18 | µA | VLOGIC = 5.5V, VCC = 5.5V | 6 | ||
| VCC supply current (write/read) | ICC | 10 | µA | VLOGIC = 1.2V, VCC = 1.7V | 6 | ||
| VLOGIC standby current | ILOGIC SB | 1 | µA | VLOGIC = VCC = 5.5V, I2C interface in standby | 6 | ||
| VLOGIC standby current | ILOGIC SB | 0.5 | µA | VLOGIC = 1.2V, VCC = 1.7V, I2C interface in standby | 6 | ||
| VCC standby current | ICC SB | 2 | µA | VLOGIC = VCC = 5.5V, I2C interface in standby | 6 | ||
| VCC standby current | ICC SB | 1.2 | µA | VLOGIC = 1.2V, VCC = 1.7V, I2C interface in standby | 6 | ||
| Leakage current on digital pins | ILkgDig | -0.4 | 0.4 | µA | Voltage at pin from GND to VLOGIC | 6 | |
| SDA output buffer LOW voltage | VOL | 0 | 0.4 | V | IOL = 3mA, VLOGIC > 2V | 7 | |
| SCL frequency | fSCL | 400 | kHz | 7 | |||
| SCL falling edge to SDA output data valid | tAA | 900 | ns | SCL falling edge crossing 30% of VLOGIC until SDA exits 30% to 70% window | 7 | ||
| Pulse width suppression time at SDA and SCL inputs | tsp | 50 | ns | Any pulse narrower than the max spec is suppressed | 7 | ||
| Bus free time before START | tBUF | 1300 | ns | SDA crossing 70% of VLOGIC during STOP to SDA crossing 70% during following START | 7 | ||
| Clock LOW time | tLOW | 1300 | ns | Measured at 30% of VLOGIC crossing | 7 | ||
| Clock HIGH time | tHIGH | 600 | ns | Measured at 70% of VLOGIC crossing | 7 | ||
| START condition set-up time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge; both crossing 70% of VLOGIC | 7 | ||
| START condition hold time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VLOGIC to SCL falling edge crossing 70% | 7 | ||
| Input data set-up time | tSU:DAT | 100 | ns | From SDA exiting 30% to 70% window to SCL rising edge crossing 30% | 7 | ||
| STOP condition set-up time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VLOGIC to SDA rising edge crossing 30% | 8 | ||
| STOP condition hold time for read or write | tHD:STO | 1300 | ns | From SDA rising edge to SCL falling edge; both crossing 70% of VLOGIC | 8 | ||
| SDA and SCL rise time | tR | 250 | ns | From 30% to 70% of VLOGIC | 8 | ||
| SDA and SCL fall time | tF | 250 | ns | From 70% to 30% of VLOGIC | 8 | ||
| Capacitive loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 8 | |
| VCC, VLOGIC ramp rate | VCC, VLOGIC Ramp | 0.01 | 50 | V/ms | Ramp monotonic at any level | 7 | |
| Wiper response time | tDCP | 3.5 | µs | T option; SCL rising edge of ACK bit after data byte to wiper new position (10% to 90% FS) | 7 | ||
| DCP recall time from shutdown | tShdnRec | 1.5 | µs | SCL rising edge of ACK bit after ACR data byte to wiper recalled position and RH connection | 7 | ||
| RH to RL resistance (nominal) | RTOTAL | 100 | kΩ | T option | 4 | ||
| End-to-end temperature coefficient | 45 | ppm/°C | T option | 4 | |||
| Resistance temperature coefficient TCR | TCR | 50 | ppm/°C | T option; wiper register set between 32 hex and FF hex | 6 | ||
| Terminal capacitance CH/CL/CW | CH/CL/CW | 32 | pF | See DCP macro model | 4 | ||
| Ratiometric temperature coefficient TCV | TCV | 2.3 | ppm/°C | T option; wiper register set to 80 hex | 5 |
CAD (KiCad official)
- Symbol:
ISL23325TFVZ - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
isl23325tfvz-etched.step/isl23325tfvz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl23325tfvz.step/isl23325tfvz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (20 pp, sha256
563c82f48e96d08e, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).