Generated by kicad-footprint-generator · KiCad file format 20260206
ISL22346UFV20Z
RENESAS · Digital Potentiometers · TSSOP-20
ISL22346UFV20Z from RENESAS, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RH3 | passive | "High" terminal of DCP3; RH3 is referenced to the wiper position, with WR3 = 127 placing the wiper closest to RH3. |
| 2 | RL3 | passive | "Low" terminal of DCP3; with WR3 = 0 the wiper is closest to RL3. |
| 3 | RW3 | passive | "Wiper" terminal of DCP3, whose position is set by the volatile Wiper Register WR3. |
| 4 | A2 | input | Device address input for the I2C interface, setting the least significant bit of the 7-bit slave address (A2 is also an input with VIH of 0.7*VCC min and VCC+0.3 max). |
| 5 | SCL | input | Open-drain I2C serial clock input that requires an external pull-up resistor. |
| 6 | SDA | bidirectional | Open-drain serial data I/O for the I2C interface that requires an external pull-up resistor (Rpu typically 1k, Cb up to 400 pF). |
| 7 | GND | power_in | Device ground pin. |
| 8 | RW2 | passive | "Wiper" terminal of DCP2, whose position is set by the volatile Wiper Register WR2. |
| 9 | RL2 | passive | "Low" terminal of DCP2; with WR2 = 0 the wiper is closest to RL2. |
| 10 | RH2 | passive | "High" terminal of DCP2; with WR2 = 127 the wiper is closest to RH2. |
| 11 | RW1 | passive | "Wiper" terminal of DCP1, whose position is set by the volatile Wiper Register WR1. |
| 12 | RL1 | passive | "Low" terminal of DCP1; with WR1 = 0 the wiper is closest to RL1. |
| 13 | RH1 | passive | "High" terminal of DCP1; with WR1 = 127 the wiper is closest to RH1. |
| 14 | A0 | input | Device address input for the I2C interface, setting the least significant bit of the 7-bit slave address. |
| 15 | A1 | input | Device address input for the I2C interface, setting the middle bit of the 7-bit slave address. |
| 16 | VCC | power_in | Power supply pin; recommended operating range is 2.7V to 5.5V. |
| 17 | SHDN | input | Active-low shutdown input that opens RHi and shorts RWi to RLi when pulled low; it must remain HIGH for normal operation. |
| 18 | RH0 | passive | "High" terminal of DCP0; with WR0 = 127 the wiper is closest to RH0. |
| 19 | RL0 | passive | "Low" terminal of DCP0; with WR0 = 0 the wiper is closest to RL0. |
| 20 | RW0 | passive | "Wiper" terminal of DCP0, whose position is set by the volatile Wiper Register WR0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TSSOP-20 |
| Category | Data Converters |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| RH to RL Resistance tolerance (W and U option) | -20 | 20 | % | W and U option | 4 | ||
| End-to-End Temperature Coefficient (U option) | -80 | 80 | ppm/°C | U option (Note 18) | 4 | ||
| Ratiometric Temperature Coefficient | TCV | -4 | 4 | ppm/°C | DCP register set to 40 hex | 5 | |
| Power Rating | 15 | mW | 4 | ||||
| Wiper Current | -3 | 3 | mA | 4 | |||
| VCC | VCC | 2.7 | 5.5 | V | 4 | ||
| Temperature Range (Extended Industrial) | -40 | 125 | °C | 4 | |||
| Storage Temperature | -65 | 150 | °C | 4 | |||
| VCC | VCC | -0.3 | 6 | V | 4 | ||
| IW (10s) | IW | -6 | 6 | mA | 10s | 4 | |
| Maximum Junction Temperature (Plastic Package) | 150 | °C | 4 | ||||
| ESD Human Body Model | 2.5 | kV | 4 | ||||
| Wiper Resistance | RW | 70 | 200 | Ω | VCC = 3.3V, wiper current = VCC/RTOTAL | 4 | |
| Integral Non-linearity | INL | -1 | 1 | LSB | Voltage divider mode; monotonic over all tap positions | 4 | |
| Differential Non-linearity | DNL | -0.5 | 0.5 | LSB | Voltage divider mode; monotonic over all tap positions | 4 | |
| Zero-scale Error (U option) | ZSerror | 0 | 0.5 | 2 | LSB | U option (Note 6) | 4 |
| Full-scale Error (U option) | FSerror | -2 | -1 | 0 | LSB | U option (Note 6) | 4 |
| DCP to DCP Matching | VMATCH | -2 | 2 | LSB | Any two DCPs at same tap position, same voltage at all RH and all RL terminals | 4 | |
| Integral Non-linearity (resistor mode) | RINL | -1 | 1 | MI | DCP register set between 10h and 7Fh; monotonic over all tap positions | 5 | |
| Differential Non-linearity (resistor mode, U option) | RDNL | -0.5 | 0.5 | MI | U option; DCP register set between 10h and 7Fh; monotonic over all tap positions | 5 | |
| Offset (U option) | Roffset | 0 | 0.5 | 2 | MI | U option (Note 14) | 5 |
| DCP to DCP Matching (resistor mode) | RMATCH | -2 | 2 | MI | Any two DCPs at the same tap position with the same terminal voltages | 5 | |
| VCC Supply Current (Volatile Write/Read) | ICC1 | 0.5 | mA | fSCL = 400kHz; SDA = Open; (for I2C, active, read and write states) | 5 | ||
| VCC Supply Current (Non-volatile Write/Read) | ICC2 | 3 | mA | fSCL = 400kHz; SDA = Open; (for I2C, active, read and write states) | 5 | ||
| VCC Current (Standby) | ISB | 5 | µA | VCC = +5.5V @ +85°C, I2C interface in standby state | 5 | ||
| VCC Current (Standby) | ISB | 7 | µA | VCC = +5.5V @ +125°C, I2C interface in standby state | 5 | ||
| VCC Current (Standby) | ISB | 3 | µA | VCC = +3.6V @ +85°C, I2C interface in standby state | 5 | ||
| VCC Current (Shutdown) | ISD | 3 | µA | VCC = +5.5V @ +85°C, I2C interface in standby state | 5 | ||
| VCC Current (Shutdown) | ISD | 5 | µA | VCC = +5.5V @ +125°C, I2C interface in standby state | 5 | ||
| VCC Current (Shutdown) | ISD | 2 | µA | VCC = +3.6V @ +85°C, I2C interface in standby state | 5 | ||
| VCC Current (Shutdown) | ISD | 4 | µA | VCC = +3.6V @ +125°C, I2C interface in standby state | 5 | ||
| Leakage Current at Pins A0, A1, A2, SHDN, SDA and SCL | ILkgDig | -1 | 1 | µA | Voltage at pin from GND to VCC | 5 | |
| DCP Wiper Response Time | tWRT | 1.5 | µs | SCL falling edge of last bit of DCP data byte to wiper new position | 5 | ||
| DCP Recall Time from Shutdown Mode | tShdnRec | 1.5 | µs | From rising edge of SHDN signal to wiper stored position and RH connection | 5 | ||
| DCP Recall Time from ACR write | tShdnRec | 1.5 | µs | SCL falling edge of last bit of ACR data byte to wiper stored position and RH connection | 5 | ||
| Power-on Recall Voltage | Vpor | 2 | 2.6 | V | Minimum VCC at which memory recall occurs | 5 | |
| VCC Ramp Rate | VCCRamp | 0.2 | V/ms | 6 | |||
| Power-up Delay | tD | 3 | ms | VCC above Vpor, to DCP Initial Value Register recall completed, and I2C Interface in standby state | 6 | ||
| EEPROM Endurance | 1e+06 | Cycles | 6 | ||||
| EEPROM Retention | 50 | Years | Temperature T < +55°C | 6 | |||
| Non-volatile Write Cycle Time | tWC | 12 | 20 | ms | 6 | ||
| SDA Output Buffer LOW Voltage, Sinking 4mA | VOL | 0.4 | V | Sinking 4mA | 6 | ||
| SCL Frequency | fSCL | 400 | kHz | 6 | |||
| Pulse Width Suppression Time at SDA and SCL Inputs | tsp | 50 | ns | Any pulse narrower than the max spec is suppressed | 6 | ||
| SCL Falling Edge to SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window | 6 | ||
| Time the Bus Must be Free Before the Start of a New Transmission | tBUF | 1300 | ns | SDA crossing 70% of VCC during a STOP condition, to SDA crossing 70% of VCC during the following START condition | 6 | ||
| Clock LOW Time | tLOW | 1300 | ns | Measured at the 30% of VCC crossing | 6 | ||
| Clock HIGH Time | tHIGH | 600 | ns | Measured at the 70% of VCC crossing | 6 | ||
| START Condition Setup Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge; both crossing 70% of VCC | 6 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC | 6 | ||
| Input Data Setup Time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC | 6 | ||
| Input Data Hold Time | tHD:DAT | 0 | ns | From SCL rising edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window | 6 | ||
| STOP Condition Setup Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC | 6 | ||
| STOP Condition Hold Time for Read, or Volatile Only Write | tHD:STO | 1300 | ns | From SDA rising edge to SCL falling edge; both crossing 70% of VCC | 6 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window | 6 | ||
| Capacitive Loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 7 | |
| RH to RL Resistance (U option) | RTOTAL | 50 | kΩ | U option (50 k part); printed unit 'k' | 4 | ||
| Potentiometer / pin capacitance (CH/CL/CW pin capacitance and A2, A1, A0, SHDN, SDA, SCL pin capacitance) | Cpin | 10 | pF | A2, A1, A0, SHDN, SDA, and SCL Pin Capacitance (Note 20: typical, not production tested) | 6 | ||
| Thermal Resistance Junction-to-Ambient, 20 Lead TSSOP | JA | 95 | °C/W | 20 Lead TSSOP (Note 1) | 4 |
CAD (KiCad official)
- Symbol:
ISL22346UFV20Z - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
isl22346ufv20z-etched.step/isl22346ufv20z-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl22346ufv20z.step/isl22346ufv20z.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (16 pp, sha256
3fbe2313661fdf71, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).