Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
ISL22317WFRTZ-TK
RENESAS · Digital Potentiometers · TDFN-10-EP(3x3)
ISL22317WFRTZ-TK from RENESAS, in a TDFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | Open drain I2C interface clock input, requires external pull-up; input high VIH 0.7VCC, low VIL 0.3VCC, max 400kHz. |
| 2 | SDA | bidirectional | Open drain serial data I/O for the I2C interface, requires an external pull-up resistor; output low voltage max 0.4V sinking 4mA. |
| 3 | A1 | input | Device address input setting the A1 bit of the 7-bit I2C slave address (addresses 50h and 54h). |
| 4 | REF_A | passive | Terminal A for an external reference resistor (10k 0.5% for W option, 50k 0.5% for U and T options); must never be connected to GND. |
| 5 | REF_B | passive | Terminal B for an external reference resistor; should be connected to GND if RL is connected to GND. |
| 6 | GND | power_in | Device ground pin. |
| 7 | RL | passive | Low terminal of the DCP; voltage range 0 to VCC-1V, must be lower than RH. |
| 8 | RW | passive | Wiper terminal of the DCP; position set by the wiper register, voltage range 0V to VCC. |
| 9 | RH | passive | High terminal of the DCP; voltage VRL+1V to VCC-0.3V, left unconnected in rheostat mode. |
| 10 | VCC | power_in | Power supply pin, 2.7V to 5.5V operating range (absolute maximum 6.0V). |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | TDFN-10-EP(3x3) |
| Category | Data Converters |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| RH to RL Resistance (W option) | RTOTAL | 10 | kΩ | W option | 3 | ||
| RH to RL Resistance Tolerance | -4 | 1 | 4 | % | W option | 3 | |
| End-to-End Temperature Coefficient | 10 | ppm/°C | All options, match external reference TCr (TCref ±10) | 3 | |||
| DCP Low Terminal Voltage | VRL | 0 | V | VRL to GND; max printed as VCC - 1V | 3 | ||
| External Reference Resistor | RREF | 10 | kΩ | for W option, 0.5% | 3 | ||
| Leakage on DCP Pins | ILkgDCP | 0.1 | 0.5 | µA | Voltage at pin from GND to VCC | 3 | |
| Integral Non-linearity (voltage divider) | INL | -0.5 | 0.1 | 0.5 | LSB | W, U or T option, VRL + 0.3V < VRW < VCC - 0.3V | 3 |
| Differential Non-linearity (voltage divider) | DNL | -0.5 | 0.1 | 0.5 | LSB | W, U or T option, VRL + 0.3V < VRW < VCC - 0.3V | 3 |
| Zero-scale Error | ZSerror | 0.5 | 2 | LSB | W, U or T option, VRL < VRW < VRL + 0.3V | 4 | |
| Full-scale Error | FSerror | -2 | -0.5 | LSB | W, U or T option, VCC - 0.3V < VRW < VCC | 4 | |
| Ratiometric Temperature Coefficient | TCV | 10 | ppm/°C | Match to external Rref, DCP register set between 15 hex and 7F hex (TCref ±10) | 4 | ||
| -3dB Cut Off Frequency | fcutoff | 1 | kHz | Wiper at midpoint (40hex) W option (10k) | 4 | ||
| Rheostat Integral Non-linearity | RINL | -3 | 1 | 3 | MI | W, U or T option, current forced to the wiper IW = (VCC - VRL)/RTOTAL | 4 |
| Rheostat Differential Non-linearity | RDNL | -3 | 1 | 3 | MI | W, U or T option, current forced to the wiper IW = (VCC - VRL)/RTOTAL | 4 |
| Rheostat Offset | Roffset | 0 | 1 | 2 | MI | W, U or T option, wiper is out of recommended operation conditions | 4 |
| Resistance Temperature Coefficient | TCR | 10 | ppm/°C | Match to external Rref, DCP register set between 15 hex and 7F hex, all options (TCref ±10) | 4 | ||
| VCC Supply Current (volatile write/read) | ICC1 | 0.6 | 1.2 | mA | VCC = +5.5V, fSCL = 400kHz; SDA = Open | 4 | |
| VCC Supply Current (volatile write/read) | ICC1 | 0.35 | 0.9 | mA | VCC = +2.7V, fSCL = 400kHz; SDA = Open, 10k | 4 | |
| VCC Supply Current (non-volatile write/read) | ICC2 | 1.75 | 2.5 | mA | VCC = +5.5V, fSCL = 400kHz; SDA = Open | 4 | |
| VCC Supply Current (non-volatile write/read) | ICC2 | 1 | 1.8 | mA | VCC = +2.7V, fSCL = 400kHz; SDA = Open | 4 | |
| VCC Current (Standby) | ISB | 0.5 | 1 | mA | VCC = +5.5V @ +125°C, I2C interface in standby state | 4 | |
| VCC Current (Standby) | ISB | 0.3 | 0.75 | mA | VCC = +2.7V @ +125°C, I2C interface in standby state, 10k | 4 | |
| VCC Current (Shutdown) | ISD | 0.5 | 1.5 | µA | VCC = +5.5V @ +125°C, I2C interface in standby state | 4 | |
| Leakage Current at REF_A, REF_B, A1, SDA, SCL | ILkgDig | -0.25 | 0.25 | µA | Voltage at pin from GND to VCC | 4 | |
| DCP Wiper Response Time | tDCP | 150 | µs | SCL falling edge of last bit of DCP data byte to wiper new position | 4 | ||
| DCP Recall Time from Shutdown Mode | tShdnRec | 150 | µs | SCL falling edge of last bit of ACR data byte to wiper stored position and RH connection | 4 | ||
| Power-on Recall Voltage | Vpor | 2.6 | V | Minimum VCC at which memory recall occurs | 4 | ||
| VCC Ramp Rate | VCC Ramp | 0.2 | 50 | V/ms | 4 | ||
| Power-up Delay | tD | 1 | ms | VCC above Vpor, to DCP Initial Value Register recall completed, and I2C Interface in standby state | 5 | ||
| Non-volatile Write Cycle Time | tWC | 12 | 20 | ms | 5 | ||
| SDA Output Buffer LOW Voltage | VOL | 0 | 0.4 | V | Sinking 4mA | 5 | |
| Pin Capacitance A1, A0, SDA, SCL | Cpin | 10 | pF | 5 | |||
| SCL Frequency | fSCL | 400 | kHz | 5 | |||
| Pulse Width Suppression Time at SDA and SCL | tsp | 50 | ns | Any pulse narrower than the max spec is suppressed | 5 | ||
| SCL Falling Edge to SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VCC, until SDA exits the 30% to 70% of VCC window | 5 | ||
| Bus Free Time Before New Transmission | tBUF | 1300 | ns | SDA crossing 70% of VCC during a STOP condition, to SDA crossing 70% of VCC during the following START condition | 5 | ||
| Clock LOW Time | tLOW | 1300 | ns | Measured at the 30% of VCC crossing | 5 | ||
| Clock HIGH Time | tHIGH | 600 | ns | Measured at the 70% of VCC crossing | 5 | ||
| START Condition Setup Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge; both crossing 70% of VCC | 5 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VCC to SCL falling edge crossing 70% of VCC | 5 | ||
| Input Data Setup Time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VCC window, to SCL rising edge crossing 30% of VCC | 5 | ||
| Input Data Hold Time | tHD:DAT | 0 | ns | From SCL falling edge crossing 70% of VCC to SDA entering the 30% to 70% of VCC window | 5 | ||
| STOP Condition Setup Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VCC, to SDA rising edge crossing 30% of VCC | 5 | ||
| STOP Condition Hold Time for Read, or Volatile Only Write | tHD:STO | 1300 | ns | From SDA rising edge to SCL falling edge; both crossing 70% of VCC | 5 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VCC, until SDA enters the 30% to 70% of VCC window | 5 | ||
| SDA and SCL Rise Time | tR | 250 | ns | From 30% to 70% of VCC | 6 | ||
| SDA and SCL Fall Time | tF | 250 | ns | From 70% to 30% of VCC | 6 | ||
| Capacitive Loading of SDA or SCL | Cb | 10 | 400 | pF | Total on-chip and off-chip | 6 | |
| SDA and SCL Bus Pull-up Resistor Off-chip | Rpu | 1 | kΩ | Maximum is determined by tR and tF | 6 | ||
| A1 Setup Time Before START condition | tSU:A | 600 | ns | 6 | |||
| A1 Hold Time After STOP condition | tHD:A | 600 | ns | 6 | |||
| Supply Voltage | VCC | -0.3 | 6 | V | 3 | ||
| Wiper Current (10s) | IW | -6 | 6 | mA | 10s | 3 | |
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Maximum Junction Temperature | 150 | °C | Plastic Package | 3 | |||
| ESD Human Body Model | 5 | kV | 3 | ||||
| Supply Voltage | VCC | 2.7 | 5.5 | V | 3 | ||
| Temperature Range (Extended Industrial) | -40 | 125 | °C | 3 | |||
| Power Rating | 15 | mW | 3 | ||||
| Wiper Current | -3 | 3 | mA | 3 | |||
| Thermal Resistance Junction to Ambient | θJA | 44 | °C/W | 10 Lead TDFN | 3 | ||
| Thermal Resistance Junction to Case | θJC | 3 | °C/W | 10 Lead TDFN | 3 |
CAD (KiCad official)
- Symbol:
ISL22317WFRTZ-TK - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: TDFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
isl22317wfrtz-tk-etched.step/isl22317wfrtz-tk-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl22317wfrtz-tk.step/isl22317wfrtz-tk.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (15 pp, sha256
e8aabbd614056070, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).