main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers isl1209iu10z-tk: viewers · Ray
isl1209iu10z-tk-etched.glb Publish 0.1.0 · Ray
isl1209iu10z-tk-etched.step isl1209iu10z-tk: factory component page (tier=mfr) · Ray
isl1209iu10z-tk-hero.glb isl1209iu10z-tk: hero GLB from the etched model (keeps the MPN mark) · Ray
isl1209iu10z-tk-hero.overlay.json Publish 0.1.0 · Ray
isl1209iu10z-tk.glb Publish 0.1.0 · Ray
isl1209iu10z-tk.kicad_mod Publish 0.1.0 · Ray
isl1209iu10z-tk.kicad_sym Publish 0.1.0 · Ray
isl1209iu10z-tk.lbr Publish 0.1.0 · Ray
isl1209iu10z-tk.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 10 pins · Ray

ISL1209IU10Z-TK

RENESAS · Real-time Clocks (RTC) · MSOP-10

ISL1209IU10Z-TK from RENESAS, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Input of the inverting crystal oscillator amplifier for an external 32.768kHz quartz crystal; it can also be driven directly from a 32.768kHz source.
2 X2 output Output of the inverting crystal oscillator amplifier for the 32.768kHz crystal, which must be left open when X1 is driven from an external source.
3 VBAT power_in Backup supply input that powers the device when VDD fails, specified at 1.8V to 5.5V, and to be tied to ground if not used.
4 GND power_in Ground reference for the device.
5 EVIN input Event input used to detect an externally monitored event, where a high signal present at the pin is detected as an event.
6 EVDET output Open drain event detect output that goes active when EVIN is triggered.
7 SDA bidirectional Serial data line for the I2C interface, with an open drain output that requires a pull-up resistor and may be wire-ORed with other open drain or open collector outputs.
8 SCL input Serial clock input used to clock all serial data into and out of the device.
9 IRQ/FOUT output Multifunction open drain output that acts as an active-low interrupt (IRQ) or as a frequency output (FOUT), selected via the configuration register.
10 VDD power_in Main power supply, operating from 2.7V to 5.5V.

Key specifications

Parameter Value
Manufacturer RENESAS
Package MSOP-10
Category Clock and Timing
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD Main Power Supply VDD 2.7 5.5 V 3
VBAT Battery Supply Voltage VBAT 1.8 5.5 V 3
Supply Current IDD1 2 6 µA VDD = 5V 3
Supply Current IDD1 1.2 4 µA VDD = 3V 3
Supply Current With I2C Active IDD2 40 120 µA VDD = 5V 3
Supply Current (Low Power Mode) IDD3 1.4 5 µA VDD = 5V, LPMODE = 1 3
Battery Supply Current IBAT 400 950 nA VBAT = 3V 3
Input Leakage Current on SCL ILI 100 nA 3
I/O Leakage Current on SDA ILO 100 nA 3
VBAT Mode Threshold VTRIP 1.6 2.2 2.6 V 3
VTRIP Hysteresis VTRIPHYS 10 30 60 mV 3
VBAT Hysteresis VBATHYS 15 50 100 mV 3
EVIN Input Low Voltage VIL -0.3 V 3
IRQ/FOUT and EVDET Output Low Voltage VOL 0.4 V VDD = 5V, IOL = 3mA 3
VDD Negative Slew Rate VDD SR- 10 V/ms 3
SDA and SCL Input Buffer Low Voltage VIL -0.3 V 4
SDA output buffer LOW voltage, sinking 3mA VOL 0.4 V VDD = 5V, IOL = 3mA 4
SDA and SCL pin capacitance Cpin 10 pF TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V, VOUT = 0V 4
SCL frequency fSCL 400 kHz 4
Pulse width suppression time at SDA and SCL inputs tIN 50 ns Any pulse narrower than the max spec is suppressed. 4
SCL falling edge to SDA output data valid tAA 900 ns SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window. 4
Bus free time before new transmission tBUF 1300 ns SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition. 4
Clock LOW time tLOW 1300 ns Measured at the 30% of VDD crossing. 4
Clock HIGH time tHIGH 600 ns Measured at the 70% of VDD crossing. 4
START condition setup time tSU:STA 600 ns SCL rising edge to SDA falling edge. Both crossing 70% of VDD. 4
START condition hold time tHD:STA 600 ns From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD. 4
Input data setup time tSU:DAT 100 ns From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD. 4
Input data hold time tHD:DAT 20 900 ns From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window. 4
STOP condition setup time tSU:STO 600 ns From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD. 4
STOP condition hold time tHD:STO 600 ns From SDA rising edge to SCL falling edge. Both crossing 70% of VDD. 4
Output data hold time tDH 0 ns From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window. 4
SDA and SCL rise time tR 300 ns From 30% to 70% of VDD. 4
SDA and SCL fall time tF 300 ns From 70% to 30% of VDD. 4
Capacitive loading of SDA or SCL Cb 10 400 pF Total on-chip and off-chip 4
Voltage on VDD, VBAT, SCL, SDA, and IRQ pins -0.5 7 V respect to ground 3
Voltage on X1 and X2 pins (VDD Mode) -0.5 V VDD Mode, respect to ground 3
Voltage on X1 and X2 pins (VBAT Mode) -0.5 V VBAT Mode, respect to ground 3
Storage Temperature -65 150 °C 3
Lead Temperature (Soldering, 10s) 300 °C Soldering, 10s 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing Abs ESD Rating (Human Body Model). . . . . . . . . . . . . . . . . . . . . .>±2kV CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a str 3

CAD (KiCad official)

  • Symbol: ISL1209IU10Z-TK
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: isl1209iu10z-tk-etched.step / isl1209iu10z-tk-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl1209iu10z-tk.step / isl1209iu10z-tk.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (25 pp, sha256 83ff3be0086bf18f, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF