Generated by kicad-footprint-generator · KiCad file format 20260206
ISL12022IBZ
RENESAS · Real-time Clocks (RTC) · SOIC-8
ISL12022IBZ from RENESAS, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Crystal input, the input of an inverting amplifier for a 32.768kHz quartz crystal, which can also be driven directly from a 32.768kHz source. |
| 2 | X2 | output | Crystal output, the output of the inverting amplifier for the crystal, which should be left open when X1 is driven from an external source. |
| 3 | VBAT | power_in | Backup supply input that powers the device when VDD fails, specified at 1.8V to 5.5V in the DC characteristics; tie to ground if not used. |
| 4 | GND | power_in | Ground reference for the device. |
| 5 | SDA | bidirectional | Open-drain serial data pin for the I2C interface, which may be wire-ORed with other open-drain or open-collector outputs and requires a pull-up resistor. |
| 6 | SCL | input | Serial clock input used to clock all serial data into and out of the device, with its input buffer disabled when the VBAT backup supply is active. |
| 7 | IRQ/FOUT | output | Open-drain multifunction pin that acts as an active-low interrupt output or as a frequency output, selected via the configuration register. |
| 8 | VDD | power_in | Main power supply, specified from 2.7V to 5.5V, with a 0.1µF capacitor recommended from VDD to ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | SOIC-8 |
| Category | Clock and Timing |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD Main Power Supply | VDD | 2.7 | 5.5 | V | 5 | ||
| VBAT Battery Supply Voltage | VBAT | 1.8 | 5.5 | V | 5 | ||
| VBAT Mode Threshold | VTRIP | 2 | 2.2 | 2.4 | V | 5 | |
| Supply Current (I2C not active, temp conversion not active, FOUT not active) | IDD1 | 4.1 | 15 | µA | VDD = 5V | 5 | |
| Supply Current (I2C not active, temp conversion not active, FOUT not active) | IDD1 | 3.5 | 14 | µA | VDD = 3V | 5 | |
| Supply Current (I2C active, temp conversion not active, FOUT not active) | IDD2 | 200 | 500 | µA | VDD = 5V | 5 | |
| Supply Current (I2C not active, temp conversion active, FOUT not active) | IDD3 | 120 | 400 | µA | VDD = 5V | 5 | |
| Battery Supply Current | IBAT | 1 | 1.6 | µA | VDD = 0V, VBAT = 3V, TA = +25°C | 5 | |
| Battery Supply Current | IBAT | 1 | 5 | µA | VDD = 0V, VBAT = 3V | 5 | |
| Battery Input Leakage | IBATLKG | 100 | nA | VDD = 5.5V, VBAT = 1.8V | 5 | ||
| Input Leakage Current on SCL | ILI | -1 | 0.1 | 1 | µA | VIL = 0V, VIH = 5.5V | 5 |
| I/O Leakage Current on SDA | ILO | -1 | 0.1 | 1 | µA | VIL = 0V, VIH = 5.5V | 5 |
| Battery Level Monitor Threshold | VBATM | -100 | 100 | mV | 5 | ||
| Brownout Level Monitor Threshold | VPBM | -100 | 100 | mV | 5 | ||
| VTRIP Hysteresis | VTRIPHYS | 30 | mV | 5 | |||
| VBAT Hysteresis | VBATHYS | 50 | mV | 5 | |||
| Oscillator Stability vs Temperature | FoutT | -5 | 5 | ppm | VDD = 3.3V | 5 | |
| Oscillator Stability vs Voltage | FoutV | -3 | 3 | ppm | 2.7V ≤ VDD ≤ 5.5V | 5 | |
| AT Sensitivity per LSB | ATLSB | 0.5 | 1 | 2 | ppm | BETA (4:0) = 10000 | 5 |
| Temperature Sensor Accuracy | Temp | -2 | 2 | °C | VDD = VBAT = 3.3V | 5 | |
| IRQ/FOUT Output Low Voltage | VOL | 0.4 | V | VDD = 5.5V, IOL = 3mA | 5 | ||
| SDA Output Buffer LOW Voltage, Sinking 3mA | VOL | 0 | 0.02 | 0.4 | V | VDD = 5V, IOL = 3mA | 6 |
| VDD Negative Slew Rate | VDDSR- | 10 | V/ms | 6 | |||
| VDD Positive Slew Rate, Minimum | VDDSR+ | 0.05 | V/ms | 6 | |||
| SDA and SCL Input Buffer LOW Voltage | VIL | -0.3 | V | 6 | |||
| SCL Frequency | fSCL | 400 | kHz | 6 | |||
| Pulse Width Suppression Time at SDA and SCL Inputs | tIN | 50 | ns | Any pulse narrower than the max spec is suppressed | 6 | ||
| SCL Falling Edge To SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window | 6 | ||
| Time the Bus Must be Free Before the Start of a New Transmission | tBUF | 1300 | ns | 6 | |||
| Clock LOW Time | tLOW | 1300 | ns | Measured at the 30% of VDD crossing | 6 | ||
| Clock HIGH Time | tHIGH | 600 | ns | Measured at the 70% of VDD crossing | 6 | ||
| START Condition Setup Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge, both crossing 70% of VDD | 6 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD | 6 | ||
| Input Data Setup Time | tSU:DAT | 100 | ns | 6 | |||
| Input Data Hold Time | tHD:DAT | 0 | 900 | ns | From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window | 6 | |
| STOP Condition Setup Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD | 6 | ||
| STOP Condition Hold Time | tHD:STO | 600 | ns | From SDA rising edge to SCL falling edge, both crossing 70% of VDD | 6 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window | 6 | ||
| Voltage on VDD, VBAT and IRQ/FOUT pins (respect to ground) | -0.3 | 6 | V | Respect to ground | 5 | ||
| Voltage on SCL and SDA pins (respect to ground) | -0.3 | V | Respect to ground; upper limit printed as VDD + 0.3V | 5 | |||
| Voltage on X1 and X2 pins (respect to ground) | -0.3 | 2.5 | V | Respect to ground | 5 | ||
| ESD Rating Human Body Model (Per MIL-STD-883 Method 3014) | 3 | kV | Human Body Model, printed as >3kV | 5 | |||
| ESD Rating Machine Model | 300 | V | Machine Model, printed as >300V | 5 | |||
| Storage Temperature | -65 | 150 | °C | 5 | |||
| Thermal Resistance Junction-to-Ambient, 8 Ld SOIC (Typical) | θJA | 102 | °C/W | Notes 4, 5: component on high effective thermal conductivity test board in free air | 5 | ||
| Thermal Resistance Junction-to-Case, 8 Ld SOIC (Typical) | θJC | 46 | °C/W | Case temp taken at package top center | 5 | ||
| Operating Temperature Range | TA | -40 | 85 | °C | Ordering part ISL12022IBZ | 3 |
CAD (KiCad official)
- Symbol:
ISL12022IBZ - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
isl12022ibz-etched.step/isl12022ibz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl12022ibz.step/isl12022ibz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (32 pp, sha256
f279e00089af47c2, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).