Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ISL12008IB8Z-T

RENESAS · Real-Time Clocks(RTC) · SOIC-8

ISL12008IB8Z-T from RENESAS, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Input of the on-chip inverting amplifier, intended to connect to one pin of an external 32.768kHz quartz crystal, and it can also be driven directly from a 32.768kHz source.
2 X2 output Output of the on-chip inverting amplifier, intended to connect to the other pin of an external 32.768kHz quartz crystal.
3 VBAT power_in Backup supply input that powers the device in the event that the VDD supply fails; it should be tied to ground if not used.
4 GND power_in Ground reference for the device.
5 SDA bidirectional Open-drain serial data pin used to transfer data into and out of the device, which may be wire-OR'ed with other open-drain or open-collector outputs.
6 SCL input Serial clock input used to clock all serial data into and out of the device.
7 FT/OUT output Open-drain 512Hz frequency output or digital output pin, with the function set via the configuration register, and it requires an external pull-up resistor.
8 VDD power_in Main power supply pin, which operates from 2.7V to 5.5V.

Key specifications

Parameter Value
Manufacturer RENESAS
Package SOIC-8
Category Clock And Timing
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD Main Power Supply VDD 2.7 5.5 V 3
VBAT Battery Supply Voltage VBAT 1.8 5.5 V 3
Voltage on VDD, VBAT, SCL, SDA, FT/OUT pins -0.5 6.5 V Respect to GND 3
Voltage on X1 and X2 pins, VDD mode -0.5 V Respect to GND; max printed as VDD + 0.5 (not converted) 3
Voltage on X1 and X2 pins, VBAT mode -0.5 V Respect to GND; max printed as VBAT + 0.5 (not converted) 3
Storage Temperature -65 150 °C 3
Operating temperature range (RTC) -40 85 °C Ordering information temp. range; ISL12008IB8Z-T 1
Supply Current IDD1 2.8 6 µA VDD = 5V 3
Supply Current IDD1 1.6 4 µA VDD = 3V 3
Supply Current With I2C Active IDD2 40 120 µA VDD = 5V 3
Supply Current (Low Power Mode) IDD3 2.3 5 µA VDD = 5V, LPMODE = 1 3
Battery Supply Current IBAT 800 950 nA VBAT = 3V, +25°C 3
Input Leakage Current on SCL ILI -1 0.1 1 µA 3
I/O Leakage Current on SDA ILO -1 0.1 1 µA 3
VBAT Mode Threshold VTRIP 2.3 2.6 2.9 V 3
FT/OUT Output Low Voltage VOL 0.02 0.4 V VDD = 5V, IOL = 3mA 3
SDA and SCL Input Buffer LOW Voltage VIL -0.3 V Max printed as 0.3 x VDD (not converted) 3
SDA Output Buffer LOW Voltage, Sinking VOL 0 0.02 0.4 V Sinking 3mA 3
Pulse width Suppression Time at SDA and SCL Inputs tIN 50 ns Any pulse narrower than the max spec is suppressed 4
Input Data Hold Time tHD:DAT 20 900 ns From SCL falling edge crossing 30% of VDD to SDA entering 30% to 70% of VDD window 4
SDA and SCL Rise Time tR 300 ns From 30% to 70% of VDD; min printed as 20 + 0.1 x Cb (not converted) 4
SDA and SCL Fall Time tF 300 ns From 70% to 30% of VDD; min printed as 20 + 0.1 x Cb (not converted) 4
Capacitive Loading of SDA or SCL Cb 10 400 pF Total on-chip and off-chip 4
SDA and SCL Bus Pull-Up Resistor Rpu 1 k Off-chip; maximum set by tR and tF (about 2k to 2.5k at Cb = 400pF) 4
VTRIP Hysteresis VTRIPHYS 36 mV Note 6 (limits typical, not production tested) 3
VBAT Hysteresis VBATHYS 53 mV Note 6 (limits typical, not production tested) 3
VDD Negative Slewrate VDD SR- 5 V/ms Note 4: required to ensure proper timekeeping 3
SDA and SCL Pin Capacitance Cpin 10 pF TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V, VOUT = 0V 3
SCL Frequency fSCL 400 kHz 4
Time the Bus Must be Free Before the Start of a New Transmission tBUF 1300 ns SDA crossing 70% of VDD during STOP to following START 4
Clock LOW Time tLOW 1300 ns Measured at 30% of VDD crossing 4
Clock HIGH Time tHIGH 600 ns Measured at 70% of VDD crossing 4
START Condition Setup Time tSU:STA 600 ns SCL rising edge to SDA falling edge, both crossing 70% of VDD 4
START Condition Hold Time tHD:STA 600 ns From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD 4
Input Data Setup Time tSU:DAT 100 ns From SDA exiting 30% to 70% of VDD window to SCL rising edge crossing 30% of VDD 4
STOP Condition Setup Time tSU:STO 600 ns From SCL rising edge crossing 70% of VDD to SDA rising edge crossing 30% of VDD 4
STOP Condition Hold Time tHD:STO 600 ns From SDA rising edge to SCL falling edge, both crossing 70% of VDD 4
Output Data Hold Time tDH 0 ns From SCL falling edge crossing 30% of VDD until SDA enters 30% to 70% of VDD window 4
Thermal Resistance, 8 Lead SOIC JA 115 °C/W Typical; measured on high effective thermal conductivity test board in free air 3

CAD (KiCad official)

  • Symbol: ISL12008IB8Z-T
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: isl12008ib8z-t-etched.step / isl12008ib8z-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); isl12008ib8z-t.step / isl12008ib8z-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (19 pp, sha256 fec87c1147703894, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF