3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownIS32LT3957A-ZLA3-TR
ISSI(Integrated Silicon Solution) · LED Drivers · TSSOP-16-EP
IS32LT3957A-ZLA3-TR from ISSI(Integrated Silicon Solution), in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | The power supply pin for the controller. |
| 2 | PWM/EN | input | PWM dimming and enable pin, internally pulled up to 5V via a 500kΩ resistor; pulling it below VIL for longer than tDELAY forces the IC into standby mode. |
| 3 | FAULTB | output | Open-drain fault reporting pin that is active low, and requires a 100kΩ resistor to the required logic level voltage. |
| 4 | FRQSS | passive | Spread spectrum frequency setting pin where a capacitor to ground sets the dither frequency, and a direct connection to ground disables the function. |
| 5 | SGND | power_in | Signal ground. |
| 6 | COMP | output | Error amplifier output for loop regulation, with a capacitor to ground setting the soft start speed. |
| 7 | RT/SYNC | bidirectional | An external resistor to ground sets the operating frequency, and the pin can also accept an external clock to synchronize two or more ICs. |
| 8 | ICTRL | input | Analog dimming voltage input with a 0.1V to 1.1V dimming range that must not be left floating, and a 10nF X7R decoupling capacitor is recommended close to the pin. |
| 9 | OVP | input | Over voltage protection input that pulls GATE low when the pin voltage exceeds VOVP_TH (1.34V typ.), so a resistor divider must keep it below VOVP_TH. |
| 10 | ISN | input | The LED current sense amplifier negative input. |
| 11 | ISP | input | The LED current sense amplifier positive input. |
| 12 | PGND | power_in | Power ground. |
| 13 | CS | input | External NMOS switch peak current sense for control loop and over current protection, connected through a resistor to ground. |
| 14 | DIMOUT | output | Buffered PWM signal that drives the LED string disconnect NMOS at the internal LDO VDD level, and pulls to ground when (VISP-VISN) exceeds VSENSE_OC; leave unconnected if unused. |
| 15 | GATE | output | Gate drive to the external power NMOS, switching between VDD and GND. |
| 16 | VDD | power_out | Internal LDO output that needs an external low ESR 1µF capacitor placed close to the pin, and is not meant to power any external circuit. |
| 17 | Thermal Pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ISSI(Integrated Silicon Solution) |
| Package | TSSOP-16-EP |
| Category | LED Drivers |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range (VCC) | VCC | 5 | 75 | V | 7 | ||
| Absolute max: VCC, PWM/EN, ISP, ISN, FAULTB pins | -0.3 | 80 | V | 7 | |||
| Absolute max: GATE, VDD, DIMOUT pins | -0.3 | 15 | V | 7 | |||
| Absolute max: COMP, RT/SYNC, ICTRL, OVP, CS pins | -0.3 | 7 | V | 7 | |||
| Operating temperature | TA=TJ | -40 | 150 | °C | 7 | ||
| Maximum operating junction temperature | TJMAX | 150 | °C | 7 | |||
| Device storage temperature | TSTG | -65 | 150 | °C | 7 | ||
| Maximum power dissipation | PDMAX | 2.5 | W | 7 | |||
| ESD (HBM) | ESD HBM | -2 | 2 | kV | 7 | ||
| ESD (CDM) | ESD CDM | -750 | 750 | V | 7 | ||
| Internal regulator output voltage | VDD | 6.05 | 6.6 | 7.05 | V | 7 | |
| Under voltage lock out falling threshold | VUVLO_F | 3.8 | 4.25 | 4.8 | V | 7 | |
| Power NMOS current limit threshold | VCS_TH | 160 | 200 | 230 | mV | 7 | |
| Output current sense threshold (VISP-VISN) | VSENSE | 245 | 250 | 255 | mV | VICTRL=1.5V, TJ=25°C | 7 |
| Output current sense threshold (VISP-VISN) | VSENSE | 241 | 250 | 259 | mV | VICTRL=1.5V, TJ=-40°C~125°C | 7 |
| Output current sense threshold with analog dimming down to 10% level | VSENSE_DIM | 22.5 | 25 | 27.5 | mV | VICTRL/VDD=0.0303, TJ=25°C | 7 |
| Output current sense threshold with analog dimming down to 10% level | VSENSE_DIM | 19 | 25 | 31 | mV | VICTRL/VDD=0.0303, TJ=-40°C~125°C | 7 |
| Output over current threshold (VISP-VISN) | VSENSE_OC | 400 | 475 | 550 | mV | For boost architecture | 8 |
| Over voltage protection threshold | VOVP_TH | 1.24 | 1.34 | 1.44 | V | OVP voltage rising | 8 |
| Operating frequency range | fSWR | 100 | 1000 | kHz | 8 | ||
| Operating frequency | fSW | 80 | 100 | 110 | kHz | RRT=430kΩ | 8 |
| Operating frequency | fSW | 220 | 250 | 280 | kHz | RRT=150kΩ | 8 |
| Operating frequency | fSW | 850 | 1000 | 1150 | kHz | RRT=33kΩ | 8 |
| Synchronized PWM frequency | fSY | 250 | 500 | kHz | 8 | ||
| Synchronization input logic high | VSY_H | 2.5 | V | Note 6 (guaranteed by design) | 8 | ||
| Synchronization input logic low | VSY_L | 0.8 | V | Note 6 (guaranteed by design) | 8 | ||
| FRQSS spread spectrum frequency range | RSS | -10 | 10 | % | Note 6 (guaranteed by design) | 9 | |
| PWM/EN input logic high | VIH | 2 | V | 9 | |||
| PWM/EN input logic low | VIL | 0.8 | V | 9 | |||
| ICTRL analog dimming range | VICTRL | 0.1 | 1.1 | V | Note 6 (guaranteed by design) | 9 | |
| Supply current | ICC | 2 | 3 | mA | VICTRL=0V | 7 | |
| Supply current in standby mode | ISTBY | 1.2 | 1.5 | mA | VPWM/EN=0V | 7 | |
| FAULTB pull low voltage | VFAULTB_LOW | 200 | 400 | mV | Fault condition, sink current IOL=1mA | 8 | |
| GATE pin rise time | tR_GATE | 25 | 60 | ns | 10%×VMAX to 5V, CGATE=3.3nF | 8 | |
| GATE pin fall time | tF_GATE | 25 | 60 | ns | 90%×VMAX to 10%×VMAX, CGATE=3.3nF | 8 | |
| GATE minimum on time | tMIN_ON | 150 | 230 | ns | 8 | ||
| DIMOUT pin rise time | tR_DIMOUT | 200 | 250 | ns | 10%×VMAX to 5V, CDIMOUT=1nF | 8 | |
| DIMOUT pin fall time | tF_DIMOUT | 120 | 180 | ns | 90%×VMAX to 10%×VMAX, CDIMOUT=1nF | 8 | |
| Junction to ambient thermal resistance (4 layer standard test PCB, JESD 51-2A) | θJA | 46.4 | °C/W | 7 | |||
| Junction to thermal pad thermal resistance (4 layer standard test PCB, JESD 51-8) | θJP | 1.617 | °C/W | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | close to this pin. This pin is not meant to power any external circuit. Thermal Pad MUST be soldered to a large size GND copper plane. | 5 |
CAD (KiCad official)
- Symbol:
IS32LT3957A-ZLA3-TR - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
is32lt3957a-zla3-tr-etched.step/is32lt3957a-zla3-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);is32lt3957a-zla3-tr.step/is32lt3957a-zla3-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ISSI(Integrated Silicon Solution) datasheet (26 pp, sha256
4aba763d0d9b1242, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).