main
Ray Publish 0.1.0 a6a36f9

IS31FL3739-GRLS4-TR

ISSI(Integrated Silicon Solution) · LED Drivers · SOP-24-300mil

IS31FL3739-GRLS4-TR from ISSI(Integrated Silicon Solution), in a SOP-24-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW2 output Switch power source for matrix row 2 (scanned high-side switch, active high when LED on).
2 SW1 output Switch power source for matrix row 1 (scanned high-side switch, active high when LED on).
3 VCC power_in Power supply, 2.7V to 5.5V (absolute max 6.0V), decoupled with capacitors close to the pin.
4 GND power_in Ground.
5 ISET passive Current setting pin; an external RISET resistor to ground (10kΩ typical) sets the CSx output current.
6 SDA bidirectional I2C serial data line, bidirectional open-drain requiring a pull-up resistor (also selectable as AD address connection).
7 SCL input I2C serial clock input, up to 1MHz.
8 SDB input Shutdown input; the chip shuts down when pulled low and a rising edge resets the I2C interface.
9 AD input I2C address setting; connect to GND, SCL, SDA or VCC to set address bits A2:A1.
10 CS1 output Current sink output 1, up to about 35mA with RISET=10kΩ.
11 CS2 output Current sink output 2, up to about 35mA with RISET=10kΩ.
12 CS3 output Current sink output 3, up to about 35mA with RISET=10kΩ.
13 CS4 output Current sink output 4, up to about 35mA with RISET=10kΩ.
14 CS5 output Current sink output 5, up to about 35mA with RISET=10kΩ.
15 GND power_in Ground.
16 CS6 output Current sink output 6, up to about 35mA with RISET=10kΩ.
17 CS7 output Current sink output 7, up to about 35mA with RISET=10kΩ.
18 SW9/CS8 output Switch power source SW9 (7×9 mode) or current sink output CS8 (8×n mode).
19 SW8 output Switch power source for matrix row 8.
20 SW7 output Switch power source for matrix row 7.
21 SW6 output Switch power source for matrix row 6.
22 SW5 output Switch power source for matrix row 5.
23 SW4 output Switch power source for matrix row 4.
24 SW3 output Switch power source for matrix row 3.

Key specifications

Parameter Value
Manufacturer ISSI(Integrated Silicon Solution)
Package SOP-24-300mil
Category Nixie Tube Driver/LED Driver
Pins 24

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 2.7 5.5 V 5
Quiescent power supply current ICC 2 3 mA VSDB= VCC, all LEDs off 5
Shutdown current ISD 3 5 µA VSDB= 0V 5
Shutdown current (software) ISD 3 5 µA SDB= VCC, Configuration Register written "0000 0000" 5
Maximum constant current of CSx IOUT 31.5 35 38.5 mA RISET= 10kΩ, GCC= "100 0000", SL= 0xFF 5
Average current on each LED ILED 4.22 mA RISET= 10kΩ, GCC= "100 0000", SL= 0xFF, n= 8, Duty= 1/8.29 5
Current switch headroom voltage SWx VHR 500 550 mV ISWITCH= 600mA RISET= 10kΩ, GCC= "100 0000", SL= 0xFF 5
Current sink headroom voltage CSx VHR 400 500 mV ISINK= 34mA, RISET= 10kΩ, GCC= "100 0000", SL= 0xFF 5
Period of scanning tSCAN 22 30 46 µs B2h= "0x01" (PWM frequency= 32kHz) 5
Non-overlap blanking time during scan tNOL1 0.3 0.8 1.2 µs B2h= "0x01" (PWM frequency= 32kHz) 5
Delay total time for CS1 to CS8 tNOL2 0.1 0.27 0.4 µs B2h= "0x01" (PWM frequency= 32kHz) 5
Logic 0 input voltage VIL 0.4 V VCC= 2.7V~5.5V, LGC= "0" 5
Logic 1 input voltage VIH 1.4 V VCC= 2.7V~5.5V, LGC= "0" 5
Logic 0 input voltage VIL 0.6 V VCC= 2.7V~5.5V, LGC= "1" 5
Logic 1 input voltage VIH 2.4 V VCC= 2.7V~5.5V, LGC= "1" 5
Input schmitt trigger hysteresis VHYS 0.2 V VCC= 3.6V, LGC= "0", LGC= "1" 5
Logic 0 input current IIL 5 nA SDB= L, VINPUT= L (Note 5) 5
Logic 1 input current IIH 5 nA SDB= L, VINPUT= H (Note 5) 5
Supply voltage VCC -0.3 6 V 5
Voltage at any input pin -0.3 6 V -0.3V ~ VCC+0.3V 5
Maximum junction temperature TJMAX 150 °C 5
Storage temperature range TSTG -65 150 °C 5
Operating temperature range TA=TJ -40 125 °C 5
Package thermal resistance, junction to ambient θJA 41 °C/W 4 layer standard test PCB based on JESD 51-2A 5
ESD (HBM) -8 8 kV 5
ESD (CDM) -750 750 V 5
Serial-clock frequency (Fast Mode) fSCL 400 kHz Fast Mode 6
Serial-clock frequency (Fast Mode Plus) fSCL 1000 kHz Fast Mode Plus 6

CAD (KiCad official)

  • Symbol: IS31FL3739-GRLS4-TR
  • Footprint: Package_SO:SOP-24_7.5x15.4mm_P1.27mm
  • 3D model: SOP-24-300mil, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 2.65 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: is31fl3739-grls4-tr-etched.step / is31fl3739-grls4-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); is31fl3739-grls4-tr.step / is31fl3739-grls4-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ISSI(Integrated Silicon Solution) datasheet (22 pp, sha256 c32010e928a5cb65, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF