main
Ray Publish 0.1.0 284fa33

IS25LP040E-JNLE-TR

ISSI(Integrated Silicon Solution) · NOR FLASH · SOIC-8

IS25LP040E-JNLE-TR from ISSI(Integrated Silicon Solution), in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: when CE# is high the device is deselected, outputs are high impedance and it enters low-power standby, and after power-up CE# must transition from high to low before a new instruction is accepted.
2 SO (IO1) bidirectional Serial Data Output in standard SPI, read on the falling edge of SCK; it becomes the bidirectional IO1 in Dual and Quad SPI and QPI modes.
3 WP# (IO2) bidirectional Write Protect: with SRWD set to 1 and WP# pulled low, the Status Register bits (SRWD, QE, BP3-BP0) are write-protected; when QE is set to 1 this pin is used as IO2 and the WP# function is not available.
4 GND power_in Ground: connect to ground when referenced to Vcc.
5 SI (IO0) bidirectional Serial Data Input in standard SPI, latching instructions, addresses and data on the rising edge of SCK; it becomes the bidirectional IO0 in Dual and Quad SPI and QPI modes.
6 SCK input Serial Data Clock: synchronized clock for input and output timing operations.
7 HOLD# (IO3) bidirectional Hold: active low, pauses serial communication without resetting the serial sequence while CE# is low, and becomes IO3 when the QE bit is set to 1.
8 Vcc power_in Power: device core power supply.

Key specifications

Parameter Value
Manufacturer ISSI(Integrated Silicon Solution)
Package SOIC-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature -65 150 °C 77
Surface Mount Lead Soldering Temperature, lead-free package 260 °C Lead-free package, 3 seconds 77
Input Voltage with Respect to Ground on All Pins -0.5 V 77
All Output Voltage with Respect to Ground -0.5 V 77
VCC Supply Voltage VCC -0.5 6 V IS25LP 77
Ambient Operating Temperature, Extended Grade E -40 105 °C Extended grade E 77
VCC Power Supply VCC 2.3 3 3.6 V IS25LP 77
VCC Active Read current ICC1 6 8 mA NORD at 50MHz 78
VCC Active Read current ICC1 7 9 mA FRD Single at 104MHz 78
VCC Active Read current ICC1 8 10 mA FRD Dual at 104MHz 78
VCC Active Read current ICC1 10 12 mA FRD Quad at 104MHz 78
VCC Program Current ICC2 15 20 mA CE# = VCC, 85°C 78
VCC Program Current ICC2 20 mA CE# = VCC, 105°C 78
VCC WRSR Current ICC3 15 20 mA CE# = VCC, 85°C 78
VCC WRSR Current ICC3 20 mA CE# = VCC, 105°C 78
VCC Erase Current (SER/BER4K/BER64K) ICC4 15 20 mA CE# = VCC, 85°C 78
VCC Erase Current (SER/BER4K/BER64K) ICC4 20 mA CE# = VCC, 105°C 78
VCC Erase Current (CE) ICC5 15 20 mA CE# = VCC, 85°C 78
VCC Erase Current (CE) ICC5 20 mA CE# = VCC, 105°C 78
VCC Standby Current CMOS ISB1 17 35 µA CE# = VCC, VIN = GND or VCC, 85°C 78
VCC Standby Current CMOS ISB1 40 µA CE# = VCC, VIN = GND or VCC, 105°C 78
Deep power down current, IS25LP ISB2 6 15 µA CE# = VCC, VIN = GND or VCC, 85°C 78
Deep power down current, IS25LP ISB2 18 µA CE# = VCC, VIN = GND or VCC, 105°C 78
Input Leakage Current ILI 1 µA VIN = 0V to VCC 78
Output Leakage Current ILO 1 µA VIN = 0V to VCC 78
Input Low Voltage VIL -0.5 V 78
Output Low Voltage VOL 0.2 V VMIN < VCC < VMAX, IOL = 100 µA 78
Input Capacitance (CE#, SCK) CIN 6 pF VIN = 0V; TA = 25°C, VCC = 3V, 1MHz 79
Input/Output Capacitance (other pins) CIN/OUT 8 pF VIN/OUT = 0V; TA = 25°C, VCC = 3V, 1MHz 79
Input Rise and Fall Times TR,TF 5 ns AC measurement conditions 79
Clock Frequency for fast read mode fCT 0 104 MHz 80
Clock Frequency for read mode fC 0 50 MHz 80
SCK High Time tCKH 4 ns 80
SCK Low Time tCKL 4 ns 80
CE# High Time tCEH 7 ns 80
CE# Setup Time tCS 5 ns 80
CE# Hold Time tCH 5 ns 80
CE# Not Active Hold Time tCHSL 5 ns 80
CE# Not Active Setup Time tSHCH 5 ns 80
Data In Setup Time tDS 2 ns 80
Data in Hold Time tDH 2 ns 80
Output Valid tV 8 ns 80
Output Hold Time tOH 2 ns 80
Output Disable Time tDIS 8 ns 80
HOLD to Output Low Z tLZ 12 ns 80
HOLD to Output High Z tHZ 12 ns 80
Sector Erase Time (4Kbyte) tEC 70 300 ms 80
Block Erase Time (32Kbyte) 130 500 ms 80
Block Erase Time (64Kbyte) 200 1000 ms Note 4: not applicable to 256Kb and 512Kb 80
Chip Erase Time, 4Mb 1.5 3 s 4Mb 80
Page Program Time tPP 0.45 1.2 ms 80
Write Status Register time tW 2 10 ms 80
Suspend to read ready tSUS 100 µs 80
Resume to next suspend tRS 80 µs 80
Deep power down tDP 3 µs 80
Vcc(min) to CE# Low tVCE 300 µs 84
Endurance 100000 Cycles JEDEC Standard A117 85
Data Retention 20 Years JEDEC Standard A117 85

CAD (KiCad official)

  • Symbol: IS25LP040E-JNLE-TR
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: is25lp040e-jnle-tr-etched.step / is25lp040e-jnle-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); is25lp040e-jnle-tr.step / is25lp040e-jnle-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: ISSI(Integrated Silicon Solution) datasheet (93 pp, sha256 682d1cb75600d9cd, retrieved 2026-10-29, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF