main
Ray
Publish 0.1.0
ab4ca71
INA321EA
The maker sells this part only as INA321EA/250, INA321EA/2K5 (TI package option addendum / ordering table: the slash suffix is the reel quantity (tape and reel); the bare code is not orderable (p.2, p.15)). The DigiKey and Mouser numbers on this page are for INA321EA/250.
Texas Instruments · Instrumentation Amplifiers · VSSOP-8
INA321EA from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RG | passive | Gain-setting node where external resistors R1 (to REF) and R2 (to VOUT) set G = 5 + 5(R2/R1), or short to VOUT for G = 5. |
| 2 | VIN− | power_in | Inverting differential input; needs a bias current return path and should be current limited to 10mA if it swings more than 0.5V beyond the supply rails. |
| 3 | VIN+ | power_in | Non-inverting differential input; needs a bias current return path and should be current limited to 10mA if it swings more than 0.5V beyond the supply rails. |
| 4 | V− | power_in | Negative supply, or ground in single-supply operation, with 0.1µF decoupling; V+ to V− is rated 7.5V max and specified 2.7V to 5.5V. |
| 5 | REF | input | Reference terminal that defines the zero-output level; requires a low-impedance connection and must be at least 1.2V below the positive supply rail. |
| 6 | VOUT | output | Rail-to-rail output optimized for loads of 10kΩ or greater, going high impedance in shutdown. |
| 7 | V+ | power_in | Positive supply, specified 2.7V to 5.5V (7.5V absolute max across V+ to V−), with 0.1µF decoupling. |
| 8 | Shutdown | input | Shutdown control, nominally tied to V+; pulling it below 0.8V on a 5V supply puts the device in sleep mode drawing under 1µA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Offset Voltage, RTI | VOS | -0.5 | 0.2 | 0.5 | mV | VS = +5V | 3 |
| Input Offset Voltage over temperature | VOS | 2.2 | 2.5 | mV | 3 | ||
| Power Supply Rejection Ratio | PSRR | -200 | 50 | 200 | µV/V | VS = +2.7V to +5.5V | 3 |
| Power Supply Rejection Ratio over temperature | PSRR | 220 | µV/V | Over temperature | 3 | ||
| Input Common-Mode Range | VCM | 0.35 | 1.5 | V | VS = 2.7V | 3 | |
| Input Common-Mode Range | VCM | 0.55 | 3.8 | V | VS = 5V | 3 | |
| Common-Mode Rejection Ratio | CMRR | 80 | dB | VS = 5V, VCM = 0.55V to 3.8V | 3 | ||
| Common-Mode Rejection Ratio over temperature | CMRR | 75 | dB | VS = 5V, VCM = 0.55V to 3.8V | 3 | ||
| Gain Range | G | 5 | 1000 | V/V | Range of gain | 3 | |
| Gain Error | GE | -0.1 | 0.02 | 0.1 | % | 3 | |
| Gain Error vs Temperature | -10 | 2 | 10 | ppm/°C | G = 5 | 3 | |
| Nonlinearity | -0.01 | 0.001 | 0.01 | % of FS | G = 25, VS = 5V, VO = 0.05 to 4.95 | 3 | |
| Nonlinearity over temperature | -0.015 | 0.002 | 0.015 | % of FS | 3 | ||
| Output Voltage Swing from Rail | 25 | 50 | mV | G ≥ 10 | 3 | ||
| Output Voltage Swing from Rail over temperature | 50 | mV | 3 | ||||
| Input Bias Current | IB | -10 | 0.5 | 10 | pA | 3 | |
| Input Offset Current | IOS | -10 | 0.5 | 10 | pA | 3 | |
| Bandwidth, -3dB | BW | 500 | kHz | G = 5 | 4 | ||
| Slew Rate | SR | 0.4 | V/µs | VS = 5V, G = 25 | 4 | ||
| Settling Time, 0.1% | tS | 8 | µs | G = 5, CL = 50pF, VO = 2V step | 4 | ||
| Settling Time, 0.01% | tS | 12 | µs | 4 | |||
| Overload Recovery | 2 | µs | 50% Input Overload, G = 25 | 4 | |||
| Specified Voltage Range | VS | 2.7 | 5.5 | V | 4 | ||
| Operating Voltage Range | VS | 2.5 | 5.5 | V | 4 | ||
| Quiescent Current per channel | IQ | 40 | 60 | µA | VSD > 2.5 | 4 | |
| Quiescent Current per channel over temperature | IQ | 70 | µA | 4 | |||
| Shutdown Quiescent Current per channel | ISD | 0.01 | 1 | µA | VSD > 0.8 | 4 | |
| Specified Temperature Range | TA | -55 | 125 | °C | 4 | ||
| Operating/Storage Temperature Range | TA | -65 | 150 | °C | 4 | ||
| Thermal Resistance junction-to-ambient | θJA | 150 | °C/W | MSOP-8, TSSOP-14, surface-mount | 4 | ||
| Supply Voltage V+ to V− | VS | 7.5 | V | 2 | |||
| Signal Input Terminal Current | II | 10 | mA | Input signals more than 0.5V beyond supply rails should be current limited | 2 | ||
| Operating Temperature | TA | -65 | 150 | °C | 2 | ||
| Storage Temperature | TSTG | -65 | 150 | °C | 2 | ||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Short-Circuit Current +ISC | +ISC | 8 | mA | 3 | |||
| Short-Circuit Current −ISC | −ISC | 16 | mA | 3 | |||
| Crosstalk, Dual | 110 | dB | 3 | ||||
| CMRR at VS = 2.7V | CMRR | 94 | dB | VS = 2.7V, VCM = 0.35V to 1.5V | 3 | ||
| Input Offset Voltage drift vs temperature | dVOS/dT | 7 | µV/°C | 3 | |||
| Long-Term Stability | 0.4 | µV/month | 3 | ||||
| Voltage Noise f = 10Hz | en | 500 | nV/√Hz | f = 10Hz | 3 | ||
| Voltage Noise f = 100Hz | en | 190 | nV/√Hz | f = 100Hz | 3 | ||
| Voltage Noise f = 1kHz | en | 100 | nV/√Hz | f = 1kHz | 3 | ||
| Voltage Noise f = 0.1Hz to 10Hz | en | 20 | µVPP | f = 0.1Hz to 10Hz | 3 | ||
| Current Noise f = 1kHz | in | 3 | fA/√Hz | f = 1kHz | 3 |
CAD (KiCad official)
- Symbol:
INA321EA - Footprint:
Package_SO:VSSOP-8_3x3mm_P0.65mm - 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ina321ea-etched.step/ina321ea-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ina321ea.step/ina321ea.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (25 pp, sha256
2363d452254a2876, retrieved 2026-11-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# INA321EA
> The maker sells this part only as INA321EA/250, INA321EA/2K5 (TI package option addendum / ordering table: the slash suffix is the reel quantity (tape and reel); the bare code is not orderable (p.2, p.15)). The DigiKey and Mouser numbers on this page are for INA321EA/250.
**Texas Instruments** · Instrumentation Amplifiers · VSSOP-8
INA321EA from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RG | passive | Gain-setting node where external resistors R1 (to REF) and R2 (to VOUT) set G = 5 + 5(R2/R1), or short to VOUT for G = 5. |
| 2 | VIN− | power_in | Inverting differential input; needs a bias current return path and should be current limited to 10mA if it swings more than 0.5V beyond the supply rails. |
| 3 | VIN+ | power_in | Non-inverting differential input; needs a bias current return path and should be current limited to 10mA if it swings more than 0.5V beyond the supply rails. |
| 4 | V− | power_in | Negative supply, or ground in single-supply operation, with 0.1µF decoupling; V+ to V− is rated 7.5V max and specified 2.7V to 5.5V. |
| 5 | REF | input | Reference terminal that defines the zero-output level; requires a low-impedance connection and must be at least 1.2V below the positive supply rail. |
| 6 | VOUT | output | Rail-to-rail output optimized for loads of 10kΩ or greater, going high impedance in shutdown. |
| 7 | V+ | power_in | Positive supply, specified 2.7V to 5.5V (7.5V absolute max across V+ to V−), with 0.1µF decoupling. |
| 8 | Shutdown | input | Shutdown control, nominally tied to V+; pulling it below 0.8V on a 5V supply puts the device in sleep mode drawing under 1µA. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Offset Voltage, RTI | VOS | -0.5 | 0.2 | 0.5 | mV | VS = +5V | 3 |
| Input Offset Voltage over temperature | VOS | | 2.2 | 2.5 | mV | | 3 |
| Power Supply Rejection Ratio | PSRR | -200 | 50 | 200 | µV/V | VS = +2.7V to +5.5V | 3 |
| Power Supply Rejection Ratio over temperature | PSRR | | | 220 | µV/V | Over temperature | 3 |
| Input Common-Mode Range | VCM | 0.35 | | 1.5 | V | VS = 2.7V | 3 |
| Input Common-Mode Range | VCM | 0.55 | | 3.8 | V | VS = 5V | 3 |
| Common-Mode Rejection Ratio | CMRR | 80 | | | dB | VS = 5V, VCM = 0.55V to 3.8V | 3 |
| Common-Mode Rejection Ratio over temperature | CMRR | 75 | | | dB | VS = 5V, VCM = 0.55V to 3.8V | 3 |
| Gain Range | G | 5 | | 1000 | V/V | Range of gain | 3 |
| Gain Error | GE | -0.1 | 0.02 | 0.1 | % | | 3 |
| Gain Error vs Temperature | | -10 | 2 | 10 | ppm/°C | G = 5 | 3 |
| Nonlinearity | | -0.01 | 0.001 | 0.01 | % of FS | G = 25, VS = 5V, VO = 0.05 to 4.95 | 3 |
| Nonlinearity over temperature | | -0.015 | 0.002 | 0.015 | % of FS | | 3 |
| Output Voltage Swing from Rail | | | 25 | 50 | mV | G ≥ 10 | 3 |
| Output Voltage Swing from Rail over temperature | | | | 50 | mV | | 3 |
| Input Bias Current | IB | -10 | 0.5 | 10 | pA | | 3 |
| Input Offset Current | IOS | -10 | 0.5 | 10 | pA | | 3 |
| Bandwidth, -3dB | BW | | 500 | | kHz | G = 5 | 4 |
| Slew Rate | SR | | 0.4 | | V/µs | VS = 5V, G = 25 | 4 |
| Settling Time, 0.1% | tS | | 8 | | µs | G = 5, CL = 50pF, VO = 2V step | 4 |
| Settling Time, 0.01% | tS | | 12 | | µs | | 4 |
| Overload Recovery | | | 2 | | µs | 50% Input Overload, G = 25 | 4 |
| Specified Voltage Range | VS | 2.7 | | 5.5 | V | | 4 |
| Operating Voltage Range | VS | 2.5 | | 5.5 | V | | 4 |
| Quiescent Current per channel | IQ | | 40 | 60 | µA | VSD > 2.5 | 4 |
| Quiescent Current per channel over temperature | IQ | | | 70 | µA | | 4 |
| Shutdown Quiescent Current per channel | ISD | | 0.01 | 1 | µA | VSD > 0.8 | 4 |
| Specified Temperature Range | TA | -55 | | 125 | °C | | 4 |
| Operating/Storage Temperature Range | TA | -65 | | 150 | °C | | 4 |
| Thermal Resistance junction-to-ambient | θJA | | 150 | | °C/W | MSOP-8, TSSOP-14, surface-mount | 4 |
| Supply Voltage V+ to V− | VS | | | 7.5 | V | | 2 |
| Signal Input Terminal Current | II | | | 10 | mA | Input signals more than 0.5V beyond supply rails should be current limited | 2 |
| Operating Temperature | TA | -65 | | 150 | °C | | 2 |
| Storage Temperature | TSTG | -65 | | 150 | °C | | 2 |
| Junction Temperature | TJ | | | 150 | °C | | 2 |
| Short-Circuit Current +ISC | +ISC | | 8 | | mA | | 3 |
| Short-Circuit Current −ISC | −ISC | | 16 | | mA | | 3 |
| Crosstalk, Dual | | | 110 | | dB | | 3 |
| CMRR at VS = 2.7V | CMRR | | 94 | | dB | VS = 2.7V, VCM = 0.35V to 1.5V | 3 |
| Input Offset Voltage drift vs temperature | dVOS/dT | | 7 | | µV/°C | | 3 |
| Long-Term Stability | | | 0.4 | | µV/month | | 3 |
| Voltage Noise f = 10Hz | en | | 500 | | nV/√Hz | f = 10Hz | 3 |
| Voltage Noise f = 100Hz | en | | 190 | | nV/√Hz | f = 100Hz | 3 |
| Voltage Noise f = 1kHz | en | | 100 | | nV/√Hz | f = 1kHz | 3 |
| Voltage Noise f = 0.1Hz to 10Hz | en | | 20 | | µVPP | f = 0.1Hz to 10Hz | 3 |
| Current Noise f = 1kHz | in | | 3 | | fA/√Hz | f = 1kHz | 3 |
## CAD (KiCad official)
- Symbol: `INA321EA`
- Footprint: `Package_SO:VSSOP-8_3x3mm_P0.65mm`
- 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `ina321ea-etched.step` / `ina321ea-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ina321ea.step` / `ina321ea.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/ina321) (25 pp, sha256 `2363d452254a2876`, retrieved 2026-11-12, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ina321ea-datasheet.pdf)