main
Ray
Publish 0.1.0
63b6b46
INA321EA
Texas Instruments · Instrumentation Amplifiers · VSSOP-8
INA321EA from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RG | passive | Gain-set terminal: the external resistor network between pins 1, 5 and 6 sets the gain as G = 5 + 5(R2/R1), with gain error from external resistors adding directly to the device error. |
| 2 | VIN− | power_in | Inverting differential input; with VS = 5 V the common-mode range is 0.55 V to 3.8 V, and input signals more than 0.5 V beyond the supply rails should be limited to 10 mA. |
| 3 | VIN+ | power_in | Non-inverting differential input; with VS = 5 V the common-mode range is 0.55 V to 3.8 V, and input current should be limited to 10 mA if signals exceed the supply rails by more than 0.5 V. |
| 4 | V− | power_in | Negative power supply terminal; the device is specified for a total supply V+ to V− of +2.7 V to +5.5 V, and operation may be single-supply with V− at ground. |
| 5 | REF | input | Reference terminal that defines the zero output level; it must be at least 1.2 V below the positive supply rail and needs a low-impedance connection, since 160 Ω in series degrades CMRR to 80 dB. |
| 6 | VOUT | output | Amplifier output, referred to the REF pin; it is optimized for load impedances of 10 kΩ or greater and swings rail-to-rail for gains of 10 or more. |
| 7 | V+ | power_in | Positive power supply terminal; the device is specified from +2.7 V to +5.5 V and should be decoupled with 0.1 µF capacitors as close to the device as possible. |
| 8 | Shutdown | input | Shutdown control normally tied to V+; pulling it below 0.8 V on a 5 V supply puts the amplifier into sleep mode (under 1 µA quiescent current) with high output impedance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Offset Voltage, RTI | VOS | -0.5 | 0.2 | 0.5 | mV | VS = +5V | 3 |
| Input Offset Voltage, over temperature | VOS | 2.5 | mV | Over temperature | 3 | ||
| Power Supply Rejection Ratio | PSRR | -200 | 50 | 200 | µV/V | VS = +2.7V to +5.5V | 3 |
| Input Common-Mode Range | 0.35 | 1.5 | V | VS = 2.7V | 3 | ||
| Input Common-Mode Range | 0.55 | 3.8 | V | VS = 5V | 3 | ||
| Common-Mode Rejection Ratio | CMRR | 80 | dB | VS = 5V, VCM = 0.55V to 3.8V | 3 | ||
| Common-Mode Rejection Ratio, over temperature | CMRR | 75 | dB | Over temperature, VS = 5V, VCM = 0.55V to 3.8V | 3 | ||
| Bias Current | IB | -10 | 0.5 | 10 | pA | 3 | |
| Offset Current | IOS | -10 | 0.5 | 10 | pA | 3 | |
| Range of Gain | 5 | 1000 | V/V | 3 | |||
| Gain Error | -0.1 | 0.02 | 0.1 | % | 3 | ||
| Gain Error vs Temperature | -10 | 2 | 10 | ppm/°C | G = 5 | 3 | |
| Nonlinearity | -0.01 | 0.001 | 0.01 | % of FS | G = 25, VS = 5V, VO = 0.05 to 4.95 | 3 | |
| Nonlinearity, over temperature | -0.015 | 0.002 | 0.015 | % of FS | Over temperature, G = 25, VS = 5V, VO = 0.05 to 4.95 | 3 | |
| Output Voltage Swing from Rail | 25 | mV | G ≥ 10 | 3 | |||
| Output Voltage Swing from Rail, over temperature | 50 | mV | Over temperature | 3 | |||
| Specified Voltage Range | 2.7 | 5.5 | V | 4 | |||
| Operating Voltage Range | 2.5 | 5.5 | V | 4 | |||
| Quiescent Current per Channel | IQ | 40 | 60 | µA | VSD > 2.5 | 4 | |
| Quiescent Current per Channel, over temperature | IQ | 70 | µA | Over temperature | 4 | ||
| Shutdown Quiescent Current per Channel | ISD | 0.01 | 1 | µA | VSD > 0.8 | 4 | |
| Specified Temperature Range | -55 | 125 | °C | 4 | |||
| Operating/Storage Temperature Range | -65 | 150 | °C | 4 | |||
| Thermal Resistance, Junction-to-Ambient | θJA | 150 | °C/W | MSOP-8, TSSOP-14 surface-mount | 4 | ||
| Supply Voltage, V+ to V− | 7.5 | V | 2 | ||||
| Signal Input Terminals Current | 10 | mA | Input signals beyond supply rails by more than 0.5V | 2 | |||
| Operating Temperature | -65 | 150 | °C | 2 | |||
| Storage Temperature | -65 | 150 | °C | 2 | |||
| Junction Temperature | 150 | °C | 2 |
CAD (KiCad official)
- Symbol:
INA321EA - Footprint:
Package_SO:VSSOP-8_3x3mm_P0.65mm - 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ina321ea-2k5-etched.step/ina321ea-2k5-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ina321ea-2k5.step/ina321ea-2k5.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (25 pp, sha256
2363d452254a2876, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# INA321EA
**Texas Instruments** · Instrumentation Amplifiers · VSSOP-8
INA321EA from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RG | passive | Gain-set terminal: the external resistor network between pins 1, 5 and 6 sets the gain as G = 5 + 5(R2/R1), with gain error from external resistors adding directly to the device error. |
| 2 | VIN− | power_in | Inverting differential input; with VS = 5 V the common-mode range is 0.55 V to 3.8 V, and input signals more than 0.5 V beyond the supply rails should be limited to 10 mA. |
| 3 | VIN+ | power_in | Non-inverting differential input; with VS = 5 V the common-mode range is 0.55 V to 3.8 V, and input current should be limited to 10 mA if signals exceed the supply rails by more than 0.5 V. |
| 4 | V− | power_in | Negative power supply terminal; the device is specified for a total supply V+ to V− of +2.7 V to +5.5 V, and operation may be single-supply with V− at ground. |
| 5 | REF | input | Reference terminal that defines the zero output level; it must be at least 1.2 V below the positive supply rail and needs a low-impedance connection, since 160 Ω in series degrades CMRR to 80 dB. |
| 6 | VOUT | output | Amplifier output, referred to the REF pin; it is optimized for load impedances of 10 kΩ or greater and swings rail-to-rail for gains of 10 or more. |
| 7 | V+ | power_in | Positive power supply terminal; the device is specified from +2.7 V to +5.5 V and should be decoupled with 0.1 µF capacitors as close to the device as possible. |
| 8 | Shutdown | input | Shutdown control normally tied to V+; pulling it below 0.8 V on a 5 V supply puts the amplifier into sleep mode (under 1 µA quiescent current) with high output impedance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Offset Voltage, RTI | VOS | -0.5 | 0.2 | 0.5 | mV | VS = +5V | 3 |
| Input Offset Voltage, over temperature | VOS | | | 2.5 | mV | Over temperature | 3 |
| Power Supply Rejection Ratio | PSRR | -200 | 50 | 200 | µV/V | VS = +2.7V to +5.5V | 3 |
| Input Common-Mode Range | | 0.35 | | 1.5 | V | VS = 2.7V | 3 |
| Input Common-Mode Range | | 0.55 | | 3.8 | V | VS = 5V | 3 |
| Common-Mode Rejection Ratio | CMRR | 80 | | | dB | VS = 5V, VCM = 0.55V to 3.8V | 3 |
| Common-Mode Rejection Ratio, over temperature | CMRR | 75 | | | dB | Over temperature, VS = 5V, VCM = 0.55V to 3.8V | 3 |
| Bias Current | IB | -10 | 0.5 | 10 | pA | | 3 |
| Offset Current | IOS | -10 | 0.5 | 10 | pA | | 3 |
| Range of Gain | | 5 | | 1000 | V/V | | 3 |
| Gain Error | | -0.1 | 0.02 | 0.1 | % | | 3 |
| Gain Error vs Temperature | | -10 | 2 | 10 | ppm/°C | G = 5 | 3 |
| Nonlinearity | | -0.01 | 0.001 | 0.01 | % of FS | G = 25, VS = 5V, VO = 0.05 to 4.95 | 3 |
| Nonlinearity, over temperature | | -0.015 | 0.002 | 0.015 | % of FS | Over temperature, G = 25, VS = 5V, VO = 0.05 to 4.95 | 3 |
| Output Voltage Swing from Rail | | | | 25 | mV | G ≥ 10 | 3 |
| Output Voltage Swing from Rail, over temperature | | | | 50 | mV | Over temperature | 3 |
| Specified Voltage Range | | 2.7 | | 5.5 | V | | 4 |
| Operating Voltage Range | | 2.5 | | 5.5 | V | | 4 |
| Quiescent Current per Channel | IQ | | 40 | 60 | µA | VSD > 2.5 | 4 |
| Quiescent Current per Channel, over temperature | IQ | | | 70 | µA | Over temperature | 4 |
| Shutdown Quiescent Current per Channel | ISD | | 0.01 | 1 | µA | VSD > 0.8 | 4 |
| Specified Temperature Range | | -55 | | 125 | °C | | 4 |
| Operating/Storage Temperature Range | | -65 | | 150 | °C | | 4 |
| Thermal Resistance, Junction-to-Ambient | θJA | | 150 | | °C/W | MSOP-8, TSSOP-14 surface-mount | 4 |
| Supply Voltage, V+ to V− | | | | 7.5 | V | | 2 |
| Signal Input Terminals Current | | | | 10 | mA | Input signals beyond supply rails by more than 0.5V | 2 |
| Operating Temperature | | -65 | | 150 | °C | | 2 |
| Storage Temperature | | -65 | | 150 | °C | | 2 |
| Junction Temperature | | | | 150 | °C | | 2 |
## CAD (KiCad official)
- Symbol: `INA321EA`
- Footprint: `Package_SO:VSSOP-8_3x3mm_P0.65mm`
- 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `ina321ea-2k5-etched.step` / `ina321ea-2k5-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ina321ea-2k5.step` / `ina321ea-2k5.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ina321.pdf) (25 pp, sha256 `2363d452254a2876`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ina321ea-2k5-datasheet.pdf)