main
Ray
Publish 0.1.0
8c8b073
INA310A2IDGKR
Texas Instruments · Current Sense Amplifiers · VSSOP-8
INA310A2IDGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VS | power_in | Power supply pin, operating from 2.7 V to 20 V, with a bypass capacitor placed close to this pin (0.1 µF recommended). |
| 2 | OUT | output | Amplifier output voltage, which can range from as low as 20 mV to as high as 200 mV below the supply voltage VS. |
| 3 | CMPIN | input | Comparator input, which accepts 0 V up to 5.5 V or up to VS if VS is lower than 5.5 V, and trips at the 0.6 V internal threshold. |
| 4 | GND | power_in | Ground reference pin for the device. |
| 5 | RESET | input | Active-low comparator reset: low or open selects transparent mode, high selects latch mode, with the pin accepting 0 V to the supply voltage. |
| 6 | CMPOUT | output | Open-drain comparator output that latches high when RESET is high, and can be pulled up through an external resistor to 0 V to 20 V independent of VS. |
| 7 | IN- | input | Shunt resistor negative sense input, connected to the load side of the sense resistor for high-side applications or to the ground side for low-side applications. |
| 8 | IN+ | input | Shunt resistor positive sense input, connected to the bus-voltage side of the sense resistor for high-side applications or to the load side for low-side applications. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VS | -0.3 | 22 | V | 4 | ||
| Analog input differential voltage | VIN+, VIN- | -12 | 12 | V | Differential (VIN+), (VIN-) | 4 | |
| Analog input voltage with respect to GND | VIN+, VIN- | -20 | 120 | V | With respect to GND | 4 | |
| Comparator output voltage | -0.3 | 22 | V | GND, 0.3 to 22 V as printed | 4 | ||
| Input current into any pin | 5 | mA | 4 | ||||
| Operating temperature | TA | -55 | 150 | °C | 4 | ||
| Junction temperature | TJ | -65 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Common-mode input range | VCM | -4 | 48 | 110 | V | 4 | |
| Operating supply voltage | VS | 2.7 | 5 | 20 | V | 4 | |
| Differential sense input range | VSENSE | 0 | V | Maximum printed as VS / G (gain-dependent expression, not numeric) | 4 | ||
| Operating free-air temperature | TA | -40 | 125 | °C | 4 | ||
| Common-mode input range | VCM | -4 | 110 | V | TA = -40°C to +125°C | 5 | |
| Common-mode rejection ratio | CMRR | 140 | 160 | dB | INA310Ax, VIN+ = -4 V to 110 V, TA = -40°C to +125°C | 5 | |
| Offset voltage, RTI | VOS | -80 | 15 | 80 | µV | INA310A2, RTI; typ printed as ±15 | 5 |
| Offset drift, RTI | dVOS/dT | -0.5 | 0.05 | 0.5 | µV/°C | TA = -40°C to +125°C, INA310A1, INA310A2, INA310A3 | 5 |
| Power-supply rejection ratio, RTI | PSRR | -3 | 0.3 | 3 | µV/V | INA310A2, INA310A3, 2.7 V ≤ VS ≤ 20 V, TA = -40°C to +125°C | 5 |
| Input bias current | IB | 10 | 20 | 30 | µA | IB+, IB-, VSENSE = 0 mV | 5 |
| Gain error | GERR | -0.15 | 0.02 | 0.15 | % | INA310Ax, GND + 50 mV ≤ VOUT ≤ VS, 200 mV | 5 |
| Gain error drift | 1 | 10 | ppm/°C | INA310Ax, TA = -40°C to +125°C | 5 | ||
| Nonlinearity error | NLERR | -0.01 | 0.01 | % | GND + 50 mV ≤ VOUT ≤ VS, 200 mV; printed as ±0.01 % | 5 | |
| Swing to GND | VSN | 5 | 20 | mV | Above GND; RLOAD = 10 kΩ to GND, TA = -40°C to +125°C, VSENSE = 0 mV | 5 | |
| Comparator alert threshold | VTHRESHOLD | 585 | 600 | 615 | mV | TA = 25°C | 6 |
| Comparator alert threshold | VTHRESHOLD | 580 | 620 | mV | TA = -40°C to +125°C | 6 | |
| Input bias current, CMPIN pin | IBCMPIN | -20 | 1 | 20 | nA | TA = 25°C, VCMPIN = 0.4 V to 1.2 V | 6 |
| Supply voltage range | VS | 2.7 | 20 | V | TA = -40°C to +125°C | 6 | |
| Quiescent current | IQ | 1.6 | 2 | mA | 6 | ||
| Quiescent current | IQ | 2.25 | mA | TA = -40°C to +125°C | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 172.2 | °C/W | DGK (VSSOP) 8 pins | 4 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 63.5 | °C/W | DGK (VSSOP) 8 pins | 4 | ||
| Junction-to-board thermal resistance | RθJB | 93.8 | °C/W | DGK (VSSOP) 8 pins | 4 | ||
| Junction-to-top characterization parameter | ΨJT | 9.8 | °C/W | DGK (VSSOP) 8 pins | 4 | ||
| Junction-to-board characterization parameter | ΨJB | 92.2 | °C/W | DGK (VSSOP) 8 pins | 4 |
CAD (KiCad official)
- Symbol:
INA310A2IDGKR - Footprint:
Package_SO:VSSOP-8_3x3mm_P0.65mm - 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ina310a2idgkr-etched.step/ina310a2idgkr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ina310a2idgkr.step/ina310a2idgkr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (34 pp, sha256
3e33543dd9085674, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# INA310A2IDGKR
**Texas Instruments** · Current Sense Amplifiers · VSSOP-8
INA310A2IDGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VS | power_in | Power supply pin, operating from 2.7 V to 20 V, with a bypass capacitor placed close to this pin (0.1 µF recommended). |
| 2 | OUT | output | Amplifier output voltage, which can range from as low as 20 mV to as high as 200 mV below the supply voltage VS. |
| 3 | CMPIN | input | Comparator input, which accepts 0 V up to 5.5 V or up to VS if VS is lower than 5.5 V, and trips at the 0.6 V internal threshold. |
| 4 | GND | power_in | Ground reference pin for the device. |
| 5 | RESET | input | Active-low comparator reset: low or open selects transparent mode, high selects latch mode, with the pin accepting 0 V to the supply voltage. |
| 6 | CMPOUT | output | Open-drain comparator output that latches high when RESET is high, and can be pulled up through an external resistor to 0 V to 20 V independent of VS. |
| 7 | IN- | input | Shunt resistor negative sense input, connected to the load side of the sense resistor for high-side applications or to the ground side for low-side applications. |
| 8 | IN+ | input | Shunt resistor positive sense input, connected to the bus-voltage side of the sense resistor for high-side applications or to the load side for low-side applications. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VSSOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VS | -0.3 | | 22 | V | | 4 |
| Analog input differential voltage | VIN+, VIN- | -12 | | 12 | V | Differential (VIN+), (VIN-) | 4 |
| Analog input voltage with respect to GND | VIN+, VIN- | -20 | | 120 | V | With respect to GND | 4 |
| Comparator output voltage | | -0.3 | | 22 | V | GND, 0.3 to 22 V as printed | 4 |
| Input current into any pin | | | | 5 | mA | | 4 |
| Operating temperature | TA | -55 | | 150 | °C | | 4 |
| Junction temperature | TJ | -65 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| Common-mode input range | VCM | -4 | 48 | 110 | V | | 4 |
| Operating supply voltage | VS | 2.7 | 5 | 20 | V | | 4 |
| Differential sense input range | VSENSE | 0 | | | V | Maximum printed as VS / G (gain-dependent expression, not numeric) | 4 |
| Operating free-air temperature | TA | -40 | | 125 | °C | | 4 |
| Common-mode input range | VCM | -4 | | 110 | V | TA = -40°C to +125°C | 5 |
| Common-mode rejection ratio | CMRR | 140 | 160 | | dB | INA310Ax, VIN+ = -4 V to 110 V, TA = -40°C to +125°C | 5 |
| Offset voltage, RTI | VOS | -80 | 15 | 80 | µV | INA310A2, RTI; typ printed as ±15 | 5 |
| Offset drift, RTI | dVOS/dT | -0.5 | 0.05 | 0.5 | µV/°C | TA = -40°C to +125°C, INA310A1, INA310A2, INA310A3 | 5 |
| Power-supply rejection ratio, RTI | PSRR | -3 | 0.3 | 3 | µV/V | INA310A2, INA310A3, 2.7 V ≤ VS ≤ 20 V, TA = -40°C to +125°C | 5 |
| Input bias current | IB | 10 | 20 | 30 | µA | IB+, IB-, VSENSE = 0 mV | 5 |
| Gain error | GERR | -0.15 | 0.02 | 0.15 | % | INA310Ax, GND + 50 mV ≤ VOUT ≤ VS, 200 mV | 5 |
| Gain error drift | | | 1 | 10 | ppm/°C | INA310Ax, TA = -40°C to +125°C | 5 |
| Nonlinearity error | NLERR | -0.01 | | 0.01 | % | GND + 50 mV ≤ VOUT ≤ VS, 200 mV; printed as ±0.01 % | 5 |
| Swing to GND | VSN | | 5 | 20 | mV | Above GND; RLOAD = 10 kΩ to GND, TA = -40°C to +125°C, VSENSE = 0 mV | 5 |
| Comparator alert threshold | VTHRESHOLD | 585 | 600 | 615 | mV | TA = 25°C | 6 |
| Comparator alert threshold | VTHRESHOLD | 580 | | 620 | mV | TA = -40°C to +125°C | 6 |
| Input bias current, CMPIN pin | IBCMPIN | -20 | 1 | 20 | nA | TA = 25°C, VCMPIN = 0.4 V to 1.2 V | 6 |
| Supply voltage range | VS | 2.7 | | 20 | V | TA = -40°C to +125°C | 6 |
| Quiescent current | IQ | | 1.6 | 2 | mA | | 6 |
| Quiescent current | IQ | | | 2.25 | mA | TA = -40°C to +125°C | 6 |
| Junction-to-ambient thermal resistance | RθJA | | 172.2 | | °C/W | DGK (VSSOP) 8 pins | 4 |
| Junction-to-case (top) thermal resistance | RθJC(top) | | 63.5 | | °C/W | DGK (VSSOP) 8 pins | 4 |
| Junction-to-board thermal resistance | RθJB | | 93.8 | | °C/W | DGK (VSSOP) 8 pins | 4 |
| Junction-to-top characterization parameter | ΨJT | | 9.8 | | °C/W | DGK (VSSOP) 8 pins | 4 |
| Junction-to-board characterization parameter | ΨJB | | 92.2 | | °C/W | DGK (VSSOP) 8 pins | 4 |
## CAD (KiCad official)
- Symbol: `INA310A2IDGKR`
- Footprint: `Package_SO:VSSOP-8_3x3mm_P0.65mm`
- 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `ina310a2idgkr-etched.step` / `ina310a2idgkr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ina310a2idgkr.step` / `ina310a2idgkr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ina310a.pdf) (34 pp, sha256 `3e33543dd9085674`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ina310a2idgkr-datasheet.pdf)