Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

INA310A1QDGKRQ1

Texas Instruments · IC · VSSOP-8

INA310A1QDGKRQ1 from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VS power_in Power supply input, operating supply range 2.7 V to 20 V.
2 OUT output Output voltage of the current-sense amplifier.
3 CMPIN input Comparator analog input.
4 GND power_in Ground reference pin.
5 RESET input Comparator reset pin, active low: Low selects transparent mode and High selects latch mode.
6 CMPOUT output Open-drain comparator output that latches high when RESET is High.
7 IN- input Shunt resistor negative sense input; connect to load side of the sense resistor for high-side applications and to ground side for low-side applications.
8 IN+ input Shunt resistor positive sense input; connect to bus-voltage side of the sense resistor for high-side applications and to load side for low-side applications.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Common-mode input range VCM -4 110 V TA = -40°C to +125°C 5
Common-mode rejection ratio CMRR 140 160 dB INA310Ax-Q1, VIN+ = -4 V to 110 V, TA = -40°C to +125°C 5
Common-mode rejection ratio at 50 kHz CMRR 85 dB INA310Ax-Q1, f = 50 kHz 5
Offset voltage, RTI (INA310A1-Q1) VOS -150 30 150 µV 5
Offset drift, RTI (INA310A1-Q1) dVOS/dT -0.5 0.05 0.5 µV/°C TA = -40°C to +125°C, INA310A1-Q1, INA310A2-Q1, INA310A3-Q1 5
Power-supply rejection ratio, RTI (INA310A1-Q1) PSRR -8 1 8 µV/V INA310A1-Q1, 2.7 V ≤ VS ≤ 20 V, TA = -40°C to +125°C 5
Input bias current IB 10 20 30 µA IB+, IB-, VSENSE = 0 mV 5
Gain error (INA310Ax-Q1) GERR -0.15 0.02 0.15 % INA310Ax-Q1, GND + 50 mV ≤ VOUT ≤ VS, 200 mV 5
Gain error drift (INA310Ax-Q1) GERR 1 10 ppm/°C INA310Ax-Q1, TA = -40°C to +125°C 5
Nonlinearity error NLERR -0.01 0.01 % GND + 50 mV ≤ VOUT ≤ VS, 200 mV 5
Maximum capacitive load 500 pF No sustained oscillation, no isolation resistor 5
Swing to VS (power-supply rail) VSP -70 -150 mV Printed as (VS), x mV; RLOAD = 10 kΩ to GND, TA = -40°C to +125°C 5
Swing to GND VSN 5 20 mV Printed as (GND) + x mV; RLOAD = 10 kΩ to GND, TA = -40°C to +125°C, VSENSE = 0 mV 5
Gain (INA310A1-Q1) G 20 V/V 5
Bandwidth (INA310A1-Q1) BW 1300 kHz CLOAD = 5 pF, VSENSE = 200 mV 6
Slew rate SR 2.5 V/µs Rising edge 6
Settling time to 0.5% tS 10 µs VOUT = 4 V ± 0.1 V step, output settles to 0.5% 6
Settling time to 1% tS 5 µs VOUT = 4 V ± 0.1 V step, output settles to 1% 6
Settling time to 5% tS 1 µs VOUT = 4 V ± 0.1 V step, output settles to 5% 6
Voltage noise density Ven 50 nV/√Hz 6
Alert threshold VTHRESHOLD 585 600 615 mV TA = 25°C 6
Alert threshold VTHRESHOLD 580 620 mV TA = -40°C to +125°C 6
Comparator hysteresis 8 mV TA = 25°C 6
Small-signal propagation delay tP 1 µs Comparator input overdrive = 20 mV 6
Slew-rate-limited propagation delay tP 1.6 µs VOUT step = 0.5 V to 4.5 V, VLIMIT = 4 V 6
Input bias current, CMPIN pin IBCMPIN -20 1 20 nA TA = 25°C, VCMPIN = 0.4 V to 1.2 V 6
Input bias current, CMPIN pin IBCMPIN 250 nA TA = -40°C to +125°C, VCMPIN = 0.4 V to 1.2 V 6
High-level leakage current ILKG 1 µA VCMPout = VS 6
Low-level output voltage VOL 300 mV IOL = 2.35 mA 6
Low-level output voltage VOL 350 mV TA = -40°C to +125°C, IOL = 2.35 mA 6
RESET high-level input voltage threshold VIH 1.2 V TA = -40°C to +125°C 6
RESET low-level input voltage threshold VIL 0.4 V TA = -40°C to +125°C 6
Minimum RESET pulse width 100 200 ns TA = -40°C to +125°C 6
RESET propagation delay 250 ns 6
Supply voltage range (INA310A1-Q1) VS 2.7 20 V TA = -40°C to +125°C 6
Quiescent current IQ 1.6 2 mA 6
Quiescent current IQ 2.25 mA TA = -40°C to +125°C 6
Common-mode input range VCM -4 48 110 V 4
Operating supply voltage VS 2.7 5 20 V 4
Differential sense input range VSENSE 0 V Upper limit printed as VS / G 4
Operating free-air temperature TA -40 125 °C 4
Supply voltage VS -0.3 22 V 4
Analog inputs differential (VIN+), (VIN-) VIN+, VIN- -12 12 V 4
Analog inputs with respect to GND VIN+, VIN- -20 120 V 4
Analog output VOUT -0.3 V Lower limit GND, 0.3; upper limit (VS) + 0.3 V 4
Comparator reset pin -0.3 V Lower limit GND, 0.3; upper limit (VS) + 0.3 V 4
Comparator analog input -0.3 V Lower limit GND, 0.3; upper limit MIN of 5.5 or VS 4
Comparator output -0.3 22 V Lower limit GND, 0.3 4
Input current into any pin 5 mA 4
Operating temperature TA -55 150 °C 4
Junction temperature TJ -65 150 °C 4
Storage temperature Tstg -65 150 °C 4
Junction-to-ambient thermal resistance (DGK VSSOP-8) RθJA 172.2 °C/W 4
Junction-to-case (top) thermal resistance (DGK VSSOP-8) RθJC(top) 63.5 °C/W 4
Junction-to-board thermal resistance (DGK VSSOP-8) RθJB 93.8 °C/W 4
Junction-to-top characterization parameter (DGK VSSOP-8) ΨJT 9.8 °C/W 4
Junction-to-board characterization parameter (DGK VSSOP-8) ΨJB 92.2 °C/W 4

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: INA310A1QDGKRQ1
  • Footprint: Package_SO:VSSOP-8_3x3mm_P0.65mm
  • 3D model: VSSOP-8, generated on the KiCad land (body 3 x 3 mm, terminals on the pads, 1.1 mm tall, datasheet A, max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ina310a1qdgkrq1-etched.step / ina310a1qdgkrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina310a1qdgkrq1.step / ina310a1qdgkrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (35 pp, sha256 cf90218870149e72, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF