main
History Download
Ray Publish 1.0.2 6747371

INA301A2IDGKR

Texas Instruments · Current Sense Amplifiers · VSSOP-8

INA301A2IDGKR from Texas Instruments, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 VS power_in Analog power supply pin, operating from 2.7 V to 5.5 V.
2 OUT output Analog output pin that provides the output voltage of the current-sense amplifier.
3 LIMIT input Analog alert threshold limit input that sets the overcurrent threshold through a single external resistor, as described in the Setting The Current-Limit Threshold section.
4 GND power_in Analog ground reference pin for the device.
5 RESET input Digital input that selects transparent or latch mode for the alert output.
6 ALERT output Overlimit alert output that is active-low and open-drain.
7 IN- input Analog input connected to the load side of the shunt resistor.
8 IN+ input Analog input connected to the supply side of the shunt resistor.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VSSOP-8
Category Amplifiers/Comparators
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VS 6 V 4
Analog input differential voltage (VIN+, VIN-) VIN -40 40 V 4
Analog input common-mode voltage 40 V GND, 0.3 V minimum (expression) to 40 V 4
ALERT pin voltage 6 V GND, 0.3 V minimum (expression) 4
Junction temperature TJ 150 °C 4
Storage temperature Tstg -65 150 °C 4
Common-mode input voltage VCM 12 V 4
Operating supply voltage VS 5 V 4
Operating free-air temperature TA -40 125 °C 4
Junction-to-ambient thermal resistance RθJA 161.5 °C/W DGK (MSOP) 8 pins 4
Junction-to-case (top) thermal resistance RθJC(top) 62.3 °C/W DGK (MSOP) 8 pins 4
Junction-to-board thermal resistance RθJB 81.4 °C/W DGK (MSOP) 8 pins 4
Junction-to-top characterization parameter ψJT 6.8 °C/W DGK (MSOP) 8 pins 4
Junction-to-board characterization parameter ψJB 80 °C/W DGK (MSOP) 8 pins 4
Common-mode input voltage range VCM 0 36 V 5
Differential input voltage range (INA301A2) VIN 0 100 mV VIN = VIN+, VIN-, INA301A2 5
Common-mode rejection (INA301A2) CMR 106 118 dB INA301A2, VIN+ = 0 V to 36 V, TA = -40ºC to +125ºC 5
Offset voltage, RTI (INA301A2) VOS -50 15 50 µV INA301A2 5
Offset voltage drift, RTI dVOS/dT 0.1 0.5 µV/°C TA= -40ºC to +125ºC 5
Power-supply rejection ratio PSRR -10 0.1 10 µV/V VS = 2.7 V to 5.5 V, VIN+ = 12 V, TA = -40ºC to +125ºC 5
Input bias current IB+, IB- 120 µA 5
Input offset current IOS -0.1 0.1 µA VSENSE = 0 mV 5
Gain error (INA301A2) -0.15 0.05 0.15 % INA301A2, VOUT = 0.5 V to VS, 0.5 V 5
Gain error drift 3 10 ppm/°C TA= -40ºC to 125ºC 5
Nonlinearity error -0.01 0.01 % VOUT = 0.5 V to VS, 0.5 V 5
Maximum capacitive load 500 pF No sustained oscillation 5
Swing to GND VGND 20 30 mV RL = 10 kΩ to GND, TA = -40ºC to +125ºC 5
Total alert propagation delay tp 0.75 1 µs Input overdrive = 1 mV 6
Slew-rate-limited propagation delay tp 1 1.5 µs VOUT step = 0.5 V to 4.5 V, VLIMIT = 4 V 6
Limit threshold output current ILIMIT 79.7 80 80.3 µA TA = 25ºC 6
Limit threshold output current ILIMIT 79.2 80.8 µA TA = -40ºC to +125ºC 6
Comparator offset voltage (INA301A2) VOS 1 4 mV INA301A2 6
Hysteresis (INA301A2) HYS 50 mV INA301A2 6
High-level input voltage VIH 1.4 6 V 6
Low-level input voltage VIL 0 0.4 V 6
Alert low-level output voltage VOL 70 300 mV IOL = 3 mA 6
ALERT pin leakage input current 0.1 1 µA VOH = 3.3 V 6
Digital leakage input current 1 µA 0 ≤ VIN ≤ VS 6
Operating supply range VS 2.7 5.5 V TA = -40ºC to +125ºC 6
Quiescent current IQ 500 650 µA VSENSE = 0 mV, TA = 25ºC 6
Quiescent current IQ 700 µA TA = -40ºC to +125ºC 6
Specified temperature range -40 125 °C 6
Gain (INA301A2) G 50 V/V INA301A2 5
Bandwidth (INA301A2) BW 500 kHz INA301A2 5
Slew rate SR 4 V/µs 5
Voltage noise density 30 nV/√Hz 5

CAD (Adom-generated)

  • Symbol: INA301A2IDGKR
  • Footprint: Adom_Gen:Texas_Instruments_INA301_e0f2ad
  • 3D model: generated to fit the land (STEP)
  • 3D model files: ina301a2idgkr-etched.step / ina301a2idgkr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina301a2idgkr.step / ina301a2idgkr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (30 pp, sha256 cef5f46eb09faa8c, retrieved 2026-11-16, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF